Instruction Manual

8
en
Operation
Using the remote control unit (some models only)
TURNING THE APPLIANCE ON
Before plugging the appliance check the caps on the back
of the unit are correctly inserted and screwed on the
drainage hose 10.
Plug into an outlet. Two lines appear on the display indicating
that the appliance is in stand-by. Press the ON/STAND-BY
button (A). When turned on, the air conditioner starts operating
in the same mode as when it was turned o. Press the MODE
button (B) until the light corresponding to the desired mode
lights up:
Light (O): air-conditioning mode
Light (P): dehumidifying mode
Light (N): fan mode
AIR CONDITIONING MODE
Ideal for hot muggy weather when you need to cool and
dehumidify the room.
The display shows the inner temperature: the light (S) turns
on.
To modify the set temperature, push the (E) or (F) button to
reach the desired temperature. The (T) light turns on and the
(S) light turns o. (To change from °F to °C or viceversa, press
for few seconds both button E and F).
After 15 seconds, the inner temperature is shown on the
display.
The (S) light turns on.
Youcanadjustthetemperatureonlyinairconditioningmode.
Then select the fan speed by pressing the FAN button (C) until
the light corresponding to the required fan speed lights up:
MAX: the air conditioner operates at maximum to achieve
the target temperature as rapidly as possible
MED: reduces noise levels while maintaining a
comfortable temperature
MIN: for silent operation
The most suitable temperature for the room during the summer
varies from 75°F to 81°F (24 to 27°C). You are recommended,
however, not to set a temperature much below the outdoor
temperature.
FAN MODE
AdjustfanspeedbypressingtheFAN button (C) as described
fortheair-conditioningmode.
Remember that the higher the speed, the more air is ltered.
If you select “MIN” speed, less air is ltered but the appliance
is also less noisy.
DEHUMIDIFYING MODE
Ideal for reducing the humidity in a room without lowering or
raising the temperature (spring or autumn, damp rooms, rainy
spells, etc). When the dehumidifying mode is selected, the
light (P) comes on. At the same time, the “MIN” fan speed light
(M) comes on. In this mode, other speeds cannot be selected.
PROGRAMMING THE TIMER
The timer can be used to delay appliance start up or shut down.
This avoids wasting electricity by optimising operating periods.
How to programme delayed start up
• PlugtheapplianceintoamainssocketandpresstheON/
OFF button (A), then select the required operating mode
and other settings (temperature, fan speed, etc).
• PresstheON/OFFbutton(A) again to place the appliance
in standby mode.
• Pressthetimerbutton(D). The timer light “H” ashes.
• Usethe+(E)or-(F) buttons to set the number of hours
delay before the appliance comes on. The time increases or
decreases in steps of one hour.
The indicator light (H) ashes until the appliance starts up.
Youcansettheappliancetocomeonwithadelayofupto12
hours. To cancel the timer programme, press the timer button
(D) again. Light (H) stops ashing.
How to programme delayed shut down
• Delayedshutdowncanbeprogrammedinanyoperating
mode (air conditioning / fan/ dehumidifying).
• Pressthetimerbutton(D). The timer light “H” ashes.
• Usethe+(E)or-(F) buttons to set the number of hours
delay before the appliance goes o.
The time increases or decreases in steps of one hour.
The light (H) ashes until the appliance turns o as
programmed. At the set time, the air conditioner shuts down
and remains in standby. To cancel the timer programme, press
the timer button (D) again.
Light (H) stops ashing.
MODELS WITH REMOTE CONTROL
• Point the remote control at the receiver on the air
conditioner. The
remote control
must be no
more than 16,4
ft (5 metres)
away from the
appliance (without obstacles between the remote control