5713215081/09.
0 BEAN TO CUP ESPRESSO AND CAPPUCCINO MACHINE DE Instruction for use GB ESAM04.
Electrical requirements Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt about your supply contact your local electricity company. The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity. Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.
A A6 A3 A4 A5 B A7 A2 B1 B6 B3 B5 A1 A8 B4 B2 A19 A18 A9 A17 A20 A16 A21 A10 A15 A11 A22 A12 A14 A23 A13 C C1 C2 C8 C3 C9 C4 C10 C5 C11 C6 C7 3 A24
1 2 3 4 5 6 8 9 10 11 12 13 14 15 4 7
M A X 16 20 7 24 28 17 18 19 22 23 25 26 27 29 30 31 21 5
Contents HEATING WATER.................................................... 14 Electrical requirements.................................... 2 Preparation............................................................................. 14 Change the quantity of water delivered automatically. . ........ 14 INTRODUCTION....................................................... 7 CLEANING............................................................. 14 Symbols used in these instructions.............................
INTRODUCTION SAFETY Thank you for choosing the ESAM04.350 automatic coffee and cappuccino maker. We hope you enjoy using your new appliance. Take a few minutes to read these instructions. This will avoid all risks and damage to the machine. Fundamental safety warnings Symbols used in these instructions Important warnings are identified by these symbols. These warnings must absolutely be respected.
• • DESCRIPTION by clients in hotels, motels and other residential type environments; bed and breakfast type environments. Description of the appliance (page 3 - A ) A1. Grinding adjustment knob A2. Main switch A3. Beans container A4. Beans container lid A5. Cover for funnel and measure compartment A6. Measure compartment A7. Cup shelf (cup warmer active, when Energy Saving is disabled) A8. Pre-ground coffee funnel A9. Hot water and steam nozzle A10. Water tank A11. Power cable A12. Cup tray A13.
s n s d C4. C5. C6. C7. C8. C9. C10. C11. MENU button: to access the settings menu. button: to turn the appliance on and off (standby) button to deliver hot water.
4. Press the or button until the required language is displayed; 5. Press the OK button to confirm; 6. Press the ESC button exit the menu. Danger of burns! During rinsing, a little hot water comes out of the coffee spouts and is collected in the drip tray underneath. Avoid contact with splashes of water. • To turn the appliance on, press the button (fig. 5). The message “Heating up Please wait” is displayed.
” r r s ” n Press the MENU button to enter the settings menu. Press the or button until “Auto-start” is displayed; Press the OK button. “Enable?” is displayed; Press the OK button. The hours flash on the display; Press the or button to select the hours; Press the OK button to confirm. The minutes flash on the display; 7. Press the or button to change the minutes; 8. Press the OK button to confirm. The symbol appears under “Auto-start” on the display. 9. Press the ESC button to exit the menu.
Corresponding coffee MY COFFEE espresso (ml) program. from ≃20 to ≃180 SHORT ≃40 STANDARD ≃60 LONG ≃90 EXTRA LONG ≃120 • • • Hot water is delivered from the spout, heating the internal circuits of the appliance and thus raising the coffee temperature. place the cups on the cup warmer until they are warm. warm the cups by rinsing them with hot water (using the hot water function). set the “high” coffee temperature (llll) in the menu.
e s e • it. This could damage the appliance. Never use more than one level measure or it could dirty the inside of the machine or block the funnel. During this time, “Preparation underway...” is displayed. Please note! If you use pre-ground coffee, you can only make one cup of coffee at a time. 1. Press the (C11) button: “Pre-ground” flashes on the display. 2. Put one level measure of pre-ground coffee into the funnel (fig. 14). 3. Place a cup under the coffee spouts (fig. 9). 4.
Cleaning the milk frother with the CLEAN button HEATING WATER Important! Danger di scottature When cleaning the internal tubes of the milk container, a little hot water leaks out of the frothed milk tube (B5). Avoid contact with splashes of water. “Press CLEAN button” flashes on the display each time you use a milk function. To eliminate all milk residues, proceed as follows: 1. Leave the milk container in the machine (you do not need to empty it); 2.
d t r , c e e - water tank (A10), coffee spouts (A16) and hot water nozzle (A9), pre-ground coffee funnel (A7), infuser (A18) milk container (B). Never immerse the coffee maker in water. 1. Check regularly (about every 100 coffees) that the inside of the appliance (accessible after removing the drip tray) is not dirty. If necessary, remove coffee deposits with the brush supplied. 2. Remove the residues with a vacuum cleaner (fig. 28).
Cleaning the hot water/steam nozzle Each time you prepare milk, clean the nozzle with a sponge to remove milk residues from the gaskets (fig. 24). PUSH symbol fully in until it clicks into place. DESCALING Descale the machine when the message “DESCALE” flashes on the display. Important! Descaler contains acids which may irritate the skin and eyes.
o e s . e r e s . s r g TECHNICAL SPECIFICATION 10. Press the OK button to start rinsing. Hot water flows out of the spout and the message “Rinsing Please wait” is displayed. 11. When the water tank is completely empty, the message “Rinsing complete Press OK” is displayed. 12. Press the OK button. The appliance goes off automatically. To turn the appliance on again, press the button. Voltage: 220-240 V~ 50/60 Hz max.
DISPLAYED MESSAGES DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY FILL TANK Insufficient water in the tank. Fill the tank with water and/or insert it correctly, pushing it as far as it will go until it clicks into place (fig. 3). GROUND TOO FINE ADJUST MILL The grinding is too fine and the coffee is delivered too slowly or not at all. Repeat coffee delivery and turn the grinding adjustment knob one click clockwise towards “7” while the coffee mill is in operation.
TROUBLESHOOTING Below is a list of some of the possible malfunctions. If the problem cannot be resolved as described, contact Customer Services. PROBLEM POSSIBLE CAUSE REMEDY The coffee is not hot The cups were not preheated. Warm the cups by rinsing them with hot water (using the hot water function). The infuser has cooled down because 2/3 minutes have elapsed since the last coffee was made. Before making the coffee, heat the infuser using the rinse button. A low coffee temperature is set.
