manual

9
pliance.
Connecttheappliancetoanecientlyearthedandcorrectly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualied
professional.
Using the coee maker for the rst time
Please note:
• Coeehasbeenusedtofactorytesttheapplianceanditis
therefore completely normal for there to be traces of cof-
fee in the mill. The machine is, however, guaranteed to be
new.
• Youshouldcustomisewaterhardnessassoonaspossible
following the instructions in the section “Setting water
hardness” on page 15.
1. Plug the appliance into the mains socket .
2. Remove the water tank, ll to the MAX line with fresh
water then replace in the appliance (g. 1).
3. Turn the cappuccino maker outwards and place a contain-Turn the cappuccino maker outwards and place a contain-
er with a minimum capacity of 100 ml underneath (g.
2).
4. Place the main switch on the back of the appliance in the
I position (g. 3).
5. The lights , , ash.
6. Turn the steam dial anticlockwise as far as it will go (g.
5). This is priming the water system. (It is normal for the
machine to make some noise).
7. Wait for delivery of hot water to stop automatically. The
lights , , alternatively ash to in-
dicate that you must close the steam tap by turning the
steam dial to the 0 position.
8. Turn the steam dial to the 0 position. The appliance goes
o automatically.
To use the appliance, turn it on.
Please note :
• When using the appliance for the rst time, you need to
make 4-5 cups of coee or 4-5 cappuccinos before the ap-
pliance starts to give satisfactory results.
TURNING THE APPLIANCE ON
Please note:
Before turning the appliance on, make sure the main switch on
the back of the appliance is in the I position (g. 3).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this
cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coee spouts
and is collected in the drip tray underneath.
Avoid contact with splashes of water.
• To turn the appliance on, press the button (g. 4).
The and lights ash while the appliance
is heating up and performing an automatic rinse cycle. By
circulating the hot water, the appliance heats both the
boiler and the internal circuits.
When the and lights remain on steadily, the
appliance is at temperature.
TURNING THE APPLIANCE OFF
Each time the appliance is turned o, it performs an automatic
rinse cycle which cannot be interrupted.
Danger of burns!
During rinsing, a little hot water ows from the coee spouts.
Avoid contact with splashes of water.
To turn the appliance o, press the button (g. 4). The
appliance performs a rinse cycle.
Please note:
If the appliance is not used for an extended period, place the
main switch in the 0 position (g. 6).
Important!
To avoid damaging the appliance, never place the main switch
(g. 6) in the 0 position while the appliance is on.
IMPOSTARE L’AUTOSPEGNIMENTO STAND
BY
The appliance is set by default to go o if not used for two
hours.
The time can be changed so that the appliance switches o
after 15 or 30 minutes, or after 1, 2 or 3 hours.
1. With the appliance in stand-by (the main switch has to be
turned to I position) (g. 3), Press and hold the ECO button
until the lights at the back of the control panel come on
(see g. after step 2).
2. Select the required period of time (15 or 30 minutes or 1,
2 or 3 hours) by pressing the button (see the light/
time table).