5713215011/01.
BEAN TO CUP ESPRESSO AND CAPPUCCINO MACHINE DE GB ESAM 04.
Electrical requirements Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt about your supply contact your local electricity company. The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity. Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.
A6 A3 A4 A5 A7 A2 A1 A8 A22 A21 A9 A20 A10 A11 A12 A19 A13 A18 A14 A15 A17 A24 A23 A25 A16 B2 B4 B6 B1 B7 B3 B8 B11 B5 B9 B12 B13 B14 B15 B16 B17 3 B10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 4 15
16 20 17 19 18 21 22 24 5 23
Contents Measuring water hardness....................................................... 15 Set water hardness.................................................................. 15 INTRODUCTION........................................................7 TECHNICAL SPECIFICATION......................................15 Symbols used in these instructions ........................................... 7 Letters in brackets......................................................................
INTRODUCTION SAFETY Thank you for choosing the „ESAM04.120“ bean to cup coffee maker. To get the best result of your new coffee machine please read these instructions carefully before use. This should ensure optimum results and maximum safety. Fundamental safety warnings Symbols used in these instructions Important warnings are identified by these symbols. These warnings must absolutely be respected.
• • • environments; farm houses by clients in hotels, motels and other residential type environments bed and breakfast type environments. B2. B3. B4. B5. B6. B7. B8. B9.
pliance. Connect the appliance to an efficiently earthed and correctly installed socket with a minimum current rating of 10A only. If the power socket does not match the plug on the appliance, have the socket replaced with a suitable type by a qualified professional. The appliance is ready for use only after completion of this cycle. Danger of burns! During rinsing, a little hot water comes out of the coffee spouts and is collected in the drip tray underneath. Avoid contact with splashes of water.
15min 30min 1h 2h 3h . 3. Press the ECO button to confirm the selection: auto-off is programmed. Please note: To disconnect the appliance completely, place the main switch at the back of the appliance in the 0 position (fig. 6). • Setting the temperature • To modify the temperature of the water used to make the coffee, proceed as follows: 1. With the appliance off and the main switch in the I position (fig. 3), press the button and hold it down until the lights on the control panel come on. 2.
If the coffee is delivered too slowly or not at all, turn one click clockwise. For fuller bodied creamier coffee, turn one click anticlockwise (do not turn more than one click at a time otherwise the coffee could be delivered a drop at a time). Please note: For hotter coffee, see the section “Tips for a hotter coffee”. • • These adjustments will only be evident after at least 2 cups of coffee have been delivered. If this adjustment does not obtain the desired result, turn the dial another click.
Cleaning the cappuccino maker after use. Clean the cappuccino maker each time you use it to avoid the build-up of milk residues or blockages. For a richer denser froth, use skimmed or partially skimmed milk at refrigerator temperature (about 5°C). To avoid milk with poor froth or large bubbles, always clean the cappuccino maker as described in the section “Cleaning the cappuccino maker”. 3. Press the button. The corresponding light flashes, indicating that the appliance is heating up; 4.
CLEANING cleaned. To remove the drip tray: 1. Remove the drip tray and the grounds container (fig. 18); 2. Empty the drip tray and grounds container and wash them; 3. Replace the drip tray and grounds container.
Do not use washing up liquid to clean the infuser as it could cause damage. 5. Soak the infuser in water for about 5 minutes, then rinse under the tap. 6. After cleaning, replace the infuser by sliding it onto the internal support and pin at the bottom, then push the PUSH symbol fully in until it clicks into place. litres under the hot water spout. 4. Wait for the and lights to come on steadily. Important! Danger of burns Hot water containing acid flows from the cappuccino maker.
2. Immerse the paper completely in a glass of water for one second. 3. Remove the paper from the water and shake lightly. After about a minute, 1, 2, 3, or 4 red squares form, depending on the hardness of the water. Each square corresponds to one level. • • • disposal Level 1 l❍❍❍ Important information for correct disposal of the product in accordance with EC Directive 2002/96/ EC. At the end of its working life, the product must not be disposed of as urban waste.
MEANING OF LIGHTS DURING NORMAL OPERATION LIGHTS 1 1 1 112 12 1 2 232 23 2 3 343 34 3 4 445 45 4 5 556 56 5 6 667 67 6 7 778 78 7 8 889 89 8 9 99 10 9 10 9 10 10 11 10 10 11 10 11 11 11 11 11 DESCRIPTION MEANING The lights flash The water is not yet at the ideal temperature.
MEANING OF THE ALARM LIGHTS LIGHTS 1 DESCRIPTION MEANING WHAT TO DO The light is on steadily Insufficient water in the tank or the tank is not correctly inserted Fill the tank with water and insert it correctly, pushing it as far as it will go until it clicks into place. The tank is dirty or clogged with limescale Rinse or descale the tank The grinding is too fine and the coffee is delivered too slowly or not at all. Repeat coffee delivery and turn the grinding adjustment knob (fig.
67 6 78 7 LIGHTS 89 8 DESCRIPTION MEANING WHAT TO DO The light is on steadily The infuser has not been replaced after cleaning.
PROBLEM POSSIBLE CAUSE SOLUTION Steam delivery stops • A safety device stops steam delivery after 3 minutes. • Wait, then activate the steam function again. The appliance does not come on. • It is not plugged into the mains socket. • Plug into the mains socket. • The main switch (A8) is not turned on. • Place the main switch in the I position (fig. 3).
