Technical data

15
come out of the holes in the chocolate carafe lid.
• Heatingthemilkcausessplashesinsidethecarafe.Thisis
normal.
• Thehotchocolatequantityinthecupwillvaryvaryingthe
density: if you choose thick density, there will be fewer
chocolate than that contained in the cup if choosing the
other densities.
MAKING MILK DRINKS
Please note!
A few seconds may elapse between Energy Saving and delivery
of the rst drink.
Filling and attaching the milk container
1. Press the release buttons and lift the milk container lid
(g. 25).
2. Fillthemilkcontainerwithasucientquantityofmilk,
not exceeding the MAX level (g. 26).
Please note!
For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C).
To avoid milk with poor froth or large bubbles, always clean
the milk lid and hot water nozzle as described in the section
“Cleaning the milk container” on pages 36 and 40.
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (g. 27).
4. Attach the lid back on the milk container.
5. Attach the container to the nozzle, pushing as far as it will
go (g. 28).
6. Placeasucientlylargecupunderthecoeespoutsand
frothed milk spout (g. 29). To use particularly tall cups/
glasses, lift the coee and milk spouts (g. 30).
7. Follow the instructions below for each function.
Adjusting the amount of froth
Turn the froth adjustment dial on the milk container lid to
adjust the amount of froth on the milk delivered while making
milk drinks (g. 31). Follow the tips given in the following
table:
Dial
position
Description Recommended for…
No froth FLAT WHITE /
MILK (hot milk)
Min. froth LATTE
Max. froth CAPPUCCINO /
MILK (frothed milk)
Making at white/cappuccino/latte/milk
1. Press the icon corresponding to the required drink.
2. After a few seconds, frothed milk is delivered from the
milk spout into the cup below. Delivery of milk stops
automatically and (if needed for the drink), coee
delivery starts. An image of the drink being prepared is
displayed (g. 32) together with a progress bar which lls
gradually.
Please note!
Milk or coee delivery can be interrupted by pressing the STOP
icon. To stop preparation altogether, press the ESC icon.
Programming the quantities of coee and milk in the
cup
The appliance is set by default to automatically deliver standard
quantities. To change these quantities, proceed as follows:
1. Place a cup under the coee spouts and milk spout.
2. Press the icon corresponding to the function to be
programmed (at white, cappuccino, latte, milk). The
machine starts delivering milk.
3. Press the PROG icon.
4. When the required quantity of milk has owed into the
cup, press the STOP MILK icon.
5. If needed for the drink, after a few seconds, the machine
starts delivering coee. When the required quantity of
coee has owed into the cup, press the STOP COFFEE
icon. Coee delivery stops.
The machine is now reprogrammed with the new quantities.
Please note!
• To cancel programming of the drinks, press the EXIT
PROG icon.
Milk drinks can be customised in all proles (see
“Memorising your personal prole” on page 17).
Cleaning the milk container after use
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout.
Avoid contact with splashes of water.
After preparing a milk drink, the machine must
be cleaned to remove the milk residues. Proceed
as follows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.