INSTALLATION and SERVICE INSTRUCTIONS USE and CARE INSTRUCTIONS DOMINO INDUCTION HOB model DE302IB distributed by DèLonghi Pty Ltd
Dear Customer, Thank you for having purchased and given your preference to our product. The safety precautions and recommendations reported below are for your own safety and that of others. They will also provide a means by which to make full use of the features offered by your appliance. Please keep this booklet in a safe place. It may be useful in future, either to yourself or to others in the event that doubts should arise relating to its operation.
BEFORE USING FOR THE FIRST TIME • Read the instructions carefully before installing and using the appliance. • After unpacking the appliance, make sure it is not damaged. In case of doubt, do not use the appliance and contact your supplier or a qualified engineer. • Remove all packaging and do not leave the packing material (plastic bags, polystyrene, bands etc) in easy reach of children as they may cause serious injury. The packaging materials are recyclable.
IMPORTANT SAFEGUARDS & RECOMMENDATIONS • Do not carry out any cleaning or maintenance without first disconnecting the appliance from the electrical supply. • During and after use of the hob, certain parts will become hot. Do not touch hot parts. • After use always ensure that the controls are in the OFF position. • Household appliances are not intended to be played with by children. • Keep children away from the hob during use.
1 FEATURES AND TECHNICAL DATA 2 1 Fig. 1.1 4 3 7 8 5 6 Electrical insulation Class I COOKING ZONES 1. Induction cooking zone Ø 140 mm - 1400 W 2. Induction cooking zone Ø 210 mm - 2200 W (3000 W with Booster function) TOUCH-CONTROL DESCRIPTION 3. ON/OFF key 4. Front zone (1) keys (increasing and decreasing power) 5. Rear zone (2) keys (increasing and decreasing power) 6. Booster function (rear zone only) (2) 7. Automatic cooking timer keys 8.
2 USE OF INDUCTION HOB Notes: – Each selection (by pressing one of the keys) is indicated by an acoustic signal (beep). – User interface initial calibration: this feature is for the keyboard calibration, to adapt the sensibility of the keys to the final mechanical, environmental and user conditions.
THERMAL PROTECTION The induction cooktop is fitted with safety devices to protect the electronic system and each cooking zone from overheating. OVERHEATING OF COOKING ZONE – Cooking zone OFF: the cooking zone display shows “ H ” and “ C” alternating or just “ C ” blinking. – Cooking zone ON: the cooking zone display alternates between set power level and “ C ”. No power is delivered to the cooking zone. Let the cooking zone cool down before using.
The ceramic cooktop is fitted with induction cooking zones. These zones, shown by painted disks on the ceramic surface, are controlled by a touch control system. INDUCTION COOKING SYSTEM When your induction hob is switched on and a cooking zone has been selected, the electronic circuits produce induced currents that instantaneously heat the bottom of the pan which then transfers this heat to the food. Cooking takes place with hardly any energy loss between the induction hob and the food.
HOW TO TURN THE TOUCH CONTROL ON AND OFF Switching ON Press the key and keep it pressed until the touch control is lighted. The displays of the cooking zones read “ 0 ”. Notes: – If the safety key-lock protection is active, the touch control can be turned ON only after having deactivated this protection. – Auto switch-off: If a cooking zone is not turned ON within 10 seconds, the touch control will automatically switch off.
POWER IGNITION AND ADJUSTMENT OF A COOKING ZONE To turn ON a cooking zone the touch control must be switched ON (see section “How To Turn the Touch Control ON and OFF”). Press the key and keep it pressed until the desired power level, ranging between 1 and 9 is set. As an alternative, press the key . The choice starts from level 9 (maximum level) down to 1 (minimum level).
BOOSTER FUNCTION REAR COOKING ZONE ONLY This function allows the cooking zone to operate at the Booster maximum power (above the nominal power) for maximum 10 minutes; it could be used, for example, to rapidly heat up large amount of water. This function is available for the rear cooking zone only. To activate the Booster function, the touch control must be switched ON (see section “How to Turn the Touch Control ON and OFF”). With the zone at any power level ( 0...
SAFETY KEY-LOCK TO PROTECT CHILDREN This function locks the touch-control keys against unwanted activation. To activate the key-lock press the key ; the indicator light above the key symbol will light up. – Cooking zone/s operating (power level already set) - with the key-lock protection active it is only possible to switch off the cooktop. – Cooktop off - with the key-lock protection active it is not possible to use the cooktop. To use the cooktop deactivate this protection.
PROGRAM FOR AUTOMATIC SWITCHING OFF OF ONE COOKING ZONE This function permits to set a timer from 1 to 99 minutes for automatic turning OFF of one cooking zone only. Note: It is not possible to set this program for both the cooking zones. With the touch control switched ON: – Press the timer keys or ; a beep sounds and the timer display shows “ 00 ”. The displays of the cooking zones show " " (timer).
OPERATION TIME LIMIT OF COOKING ZONES Each cooking zone is automatically switched OFF after a maximum preset time if no operation is performed. The maximum preset time limit depends on the set power level, as illustrated in this schedule. Each operation on the cooking hob by using the keys , will reset the maximum operation time at its initial value.
ERROR CODE ON THE DISPLAY/S If an error message appears on the display/s (the display/s show/s “ F ” and another character alternating - e.g. “ F ” and “ A ”, “ F ” and “ 0 ”, .....) : 1. Disconnect the cooktop from the mains. 2. Reconnect the cooktop and turn it on. 3. Wait for about two minutes and if the problem does not appear the cooktop can be used. 4. If the problem does not disappear repeat step from 1 to 3. 5.
3 CLEANING AND MAINTENANCE CLEANING THE CERAMIC HOB Before you begin cleaning make sure that the hob is switched off. • Remove spillages and other types of incrustations. • Dust or food particles can be removed with a damp cloth. • If you use a detergent, please make sure that it is not abrasive or scouring. Abrasive or scouring powders can damage the glass surface of the hob. • All traces of the cleaner must be removed with a damp cloth.
ADVICE FOR THE INSTALLER 17
4 INSTALLATION CAUTION: • This appliance shall only be serviced by authorized personnel. • This appliance is to be installed only by an authorised person according to the current local regulations and in observation of the manufacturer’s instructions. • Incorrect installation, for which the manufacturer accepts no responsibility, may cause personal injury of damage. • Always disconnect the cooktop from mains power supply before carrying out any maintenance operations or repairs.
This cooktop can be built into a working surface 30 to 40 mm thick and 600 mm deep. 450 mm • The cooktop shall not be installed directly above a dishwasher, fridge, freezer, washing machine or clothes dryer, as the humidity may damage the cooktop electronics. • If the cooktop is installed above an oven, the oven shall be provided with cooling fan. The two appliances should be connected to the electrical supply with independent connections.
FASTENING THE COOKTOP Each cooktop is supplied with a set of tabs and screws to fasten it on units with a working surface from 3 to 4 cm deep. The kit includes 4 tabs A and 4 self-threading screws B (fig. 4.4). • • • • • • • • Cut the unit. Turn the hob upside down and rest the glass side on a cloth. Spread the seal C around the edge of the hob (fig. 4.5). Put tabs A into the mountings; only tighten screws B a few turns. Make sure that the tabs are mounted correctly as shown in the figure 4.4.
5 ELECTRICAL CONNECTION IMPORTANT: Installation must be carried out according to the manufacturer’s instructions. Incorrect installation may cause harm and damage to people, animals or property, for which the manufacturer accepts no responsibility. Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains. Connection to a good earth wiring system is absolutely essential.
CONNECTING OF THE POWER SUPPLY CABLE • Unhook the terminal board cover by inserting a screwdriver into the two hooks A (fig. 5.1). • Open the cable gland by unscrewing screw F (fig. 5.3), unscrew the terminal screws and remove the cable. • The new supply cable, of suitable type and section, is connected to the terminal board following the diagram of fig. 5.2. FEEDER CABLE SECTION “Type H05RR-F” 230-240 V ~ 3 x 1.5 mm2 3600 W MAX (15.
Descriptions and illustrations in this booklet are given as simply indicative. The manufacturer reserves the right, considering the characteristics of the models described here, at any time and without notice, to make eventual necessary modifications for their construction or for commercial needs.
cod.
