Users Guide
Table Of Contents
- Dell Wyse 3040 Thin Client User Guide
- Welcome to Dell Wyse 3040 thin client
- Wyse 3040 thin client hardware installation
- Wyse 3040 thin client on ThinOS
- Logging on to the Wyse 3040 thin client running Wyse ThinOS
- Configuring the dual head display settings in Dell Wyse ThinOS
- Configuring the network settings on Dell Wyse ThinOS
- Configuring peripherals settings on Wyse ThinOS
- Power state
- Configuring the broker setup on Dell Wyse ThinOS
- Configuring the WDA settings on Dell Wyse ThinOS
- Wyse 3040 thin client on ThinLinux
- Accessing thin client BIOS settings on Wyse ThinLinux
- Logging on to the Wyse 3040 thin client running ThinLinux
- Configuring display on Dell Wyse ThinLinux
- Configuring the network settings on Dell WyseThinLinux
- Configuring peripherals settings on Wyse ThinLinux
- Power state
- Configuring connections locally on Dell Wyse ThinLinux
- Configuring WDA settings on Dell Wyse ThinLinux
- Major components of your system
- System specifications
- Thermal management on Wyse 3040 thin client
- BIOS overview
- Accessing thin client BIOS settings
- System Setup overview
- Boot Sequence
- Navigation keys
- General screen options
- System Configuration screen options
- Security screen options
- Secure Boot screen options
- Performance screen options
- Power Management screen options
- POST Behavior screen options
- Virtualization support screen options
- Maintenance screen options
- System Log screen options
- Updating the BIOS
- Troubleshooting your system
● IPv6 Address
● Hardware Address
● Default Route
● DNS
4. Click the Security tab to configure the 802.1x security settings.
a. Click the ON button to enable the 802.1x Security for your network connection.
b. From the Authentication drop-down list, select the type of authentication you want to set for your network connection.
The available options are:
● TLS
● Protected EAP (PEAP)
You must configure TLS and PEAP using the INI parameters only. Options that you configure using the INI parameters
are populated on the UI screen. For more information about the usage of INI parameters, see Dell Wyse ThinLinux INI
Reference Guide.
NOTE: You cannot configure the 802.1x authentication settings using the GUI options.
5. Click the Identity tab and configure the following settings:
NOTE: Only Administrators are allowed to authenticate these settings by entering the admin password in the root
privilege authentication dialog box after a particular setting is changed or configured.
a. Name—Specifies the default name of the wired connection. If you want to set your preferred name for the connection,
enter the name and then click Apply.
b. MAC Address—Specifies the MAC address of the network connection.
c. Cloned Address—Specifies the IP address that is cloned by the router.
d. Maximum transmission unit (MTU)—Specifies the size (in bytes) of the largest protocol data unit that the protocol
layer can pass onwards.
e. Firewall Zone—Specifies the security level of the connection.
f. Connect automatically— Select this check box to automatically connect to the network after you plug-in the network
wire.
g. Make available to other users— Select this check box if you want to allow other users to configure these settings.
6. Click the IPv4 tab and do the following:
a. Enable the IPv4 button to configure the IPv4 settings.
b. From the Addresses drop-down menu, select the type of IPv4 configuration. The available options are:
● Automatic (DHCP)
● Manual
● Link-Local Only
c. If Automatic (DHCP) option is selected, you must configure the following options.
Table 4. Automatic (DHCP)
Parameter Description
DNS Enable the Automatic button, if you want the thin client
to automatically fetch the DNS Server.
Server Specifies the IP address of the DNS Server.
Click the + icon to add a new DNS server to the list.
Routes Enable the Automatic button to turn on the automatic
IPv4 routing.
Address Specifies the Router IP address.
Netmask Specifies the Netmask. Netmask is used to divide an IP
address into subnets and specify the network's available
hosts.
Gateway Specifies the IP address of the default Gateway.
34 Wyse 3040 thin client on ThinLinux