Concept Guide
Table Of Contents
- About this Guide
- About Instant
- Setting up a W-IAP
- Automatic Retrieval of Configuration
- Instant User Interface
- Initial Configuration Tasks
- Customizing W-IAP Settings
- Modifying the W-IAP Host Name
- Configuring Zone Settings on a W-IAP
- Specifying a Method for Obtaining IP Address
- Configuring External Antenna
- Configuring Radio Profiles for a W-IAP
- Configuring Uplink VLAN for a W-IAP
- Changing the W-IAP Installation Mode
- Changing USB Port Status
- Master Election and Virtual Controller
- Adding a W-IAP to the Network
- Removing a W-IAP from the Network
- VLAN Configuration
- IPv6 Support
- Wireless Network Profiles
- Configuring Wireless Network Profiles
- Configuring Fast Roaming for Wireless Clients
- Configuring Modulation Rates on a WLAN SSID
- Multi-User-MIMO
- Management Frame Protection
- Disabling Short Preamble for Wireless Client
- Editing Status of a WLAN SSID Profile
- Editing a WLAN SSID Profile
- Deleting a WLAN SSID Profile
- Wired Profiles
- Captive Portal for Guest Access
- Understanding Captive Portal
- Configuring a WLAN SSID for Guest Access
- Configuring Wired Profile for Guest Access
- Configuring Internal Captive Portal for Guest Network
- Configuring External Captive Portal for a Guest Network
- Configuring Facebook Login
- Configuring Guest Logon Role and Access Rules for Guest Users
- Configuring Captive Portal Roles for an SSID
- Configuring Walled Garden Access
- Authentication and User Management
- Managing W-IAP Users
- Supported Authentication Methods
- Supported EAP Authentication Frameworks
- Configuring Authentication Servers
- Understanding Encryption Types
- Configuring Authentication Survivability
- Configuring 802.1X Authentication for a Network Profile
- Enabling 802.1X Supplicant Support
- Configuring MAC Authentication for a Network Profile
- Configuring MAC Authentication with 802.1X Authentication
- Configuring MAC Authentication with Captive Portal Authentication
- Configuring WISPr Authentication
- Blacklisting Clients
- Uploading Certificates
- Roles and Policies
- DHCP Configuration
- Configuring Time-Based Services
- Dynamic DNS Registration
- VPN Configuration
- IAP-VPN Deployment
- Adaptive Radio Management
- Deep Packet Inspection and Application Visibility
- Voice and Video
- Services
- Configuring AirGroup
- Configuring a W-IAP for RTLS Support
- Configuring a W-IAP for Analytics and Location Engine Support
- Managing BLE Beacons
- Clarity Live
- Configuring OpenDNS Credentials
- Integrating a W-IAP with Palo Alto Networks Firewall
- Integrating a W-IAP with an XML API Interface
- CALEA Integration and Lawful Intercept Compliance
- Cluster Security
- W-IAP Management and Monitoring
- Uplink Configuration
- Intrusion Detection
- Mesh W-IAP Configuration
- Mobility and Client Management
- Spectrum Monitor
- W-IAP Maintenance
- Monitoring Devices and Logs
- Hotspot Profiles
- ClearPass Guest Setup
- IAP-VPN Deployment Scenarios
- Acronyms and Abbreviations
410 | IAP-VPN Deployment Scenarios Dell Networking W-Series Instant 6.5.1.0-4.3.1.0 | User Guide
Configuration Steps CLI Commands UI Procedure
5. Create authentication
servers for user
authentication. The
example in the next
column assumes 802.1X
SSID.
(Instant AP)(config)# wlan auth-server server1
(Instant AP)(Auth Server "server1")# ip 10.2.2.1
(Instant AP)(Auth Server "server1")# port 1812
(Instant AP)(Auth Server "server1")# acctport 1813
(Instant AP)(Auth Server "server1")# key
"presharedkey"
(Instant AP)(Auth Server "server1")# exit
(Instant AP)(config)# wlan auth-server server2
(Instant AP)(Auth Server "server1")# ip 10.2.2.2
(Instant AP)(Auth Server "server1")# port 1812
(Instant AP)(Auth Server "server1")# acctport 1813
(Instant AP)(Auth Server "server1")# key
"presharedkey"
See
Configuring an
External Server
for
Authentication
6. Configure wired and
wireless SSIDs using the
authentication servers
and access rules; enable
authentication
survivability.
Configure wired ports to operate in Centralized, L2 mode and
associate VLAN 20 to the wired port profile.
(Instant AP)(config) # wired-port-profile wired-
port
(Instant AP)(wired-port-profile "wired-port")#
switchport-mode access
(Instant AP)(wired-port-profile "wired-port")#
allowed-vlan all
(Instant AP)(wired-port-profile "wired-port")#
native-vlan 20
(Instant AP)(wired-port-profile "wired-port")# no
shutdown
(Instant AP)(wired-port-profile "wired-port")#
access-rule-name wired-port
(Instant AP)(wired-port-profile "wired-port")# type
employee
(Instant AP)(wired-port-profile "wired-port")#
auth-server server1
(Instant AP)(wired-port-profile "wired-port")#
auth-server server2
(Instant AP)(wired-port-profile "wired-port")#
dot1x
(Instant AP)(wired-port-profile "wired-port")# exit
(Instant AP)(config)# enet1-port-profile wired-port
Configure a wireless SSID to operate in Centralized, L2 mode and
associate VLAN 20 to the WLAN SSID profile.
(Instant AP)(config) # wlan ssid-profile wireless-
ssid
(Instant AP)(SSID Profile "wireless-ssid")# enable
(Instant AP)(SSID Profile "wireless-ssid")# type
employee
(Instant AP)(SSID Profile "wireless-ssid")# essid
wireless-ssid
(Instant AP)(SSID Profile "wireless-ssid")# opmode
wpa2-aes
(Instant AP)(SSID Profile "wireless-ssid")# vlan 20
(Instant AP)(SSID Profile "wireless-ssid")# auth-
server server1
(Instant AP)(SSID Profile "wireless-ssid")# auth-
server server2
See
Configuring a
Wired Profile
and Wireless
Network
Profiles
Table 87: W-IAP Configuration for Scenario—GRE: Single Datacenter Deployment with No Redundancy