Concept Guide
Table Of Contents
- About this Guide
- About Instant
- Setting up a W-IAP
- Automatic Retrieval of Configuration
- Instant User Interface
- Initial Configuration Tasks
- Customizing W-IAP Settings
- Modifying the W-IAP Host Name
- Configuring Zone Settings on a W-IAP
- Specifying a Method for Obtaining IP Address
- Configuring External Antenna
- Configuring Radio Profiles for a W-IAP
- Configuring Uplink VLAN for a W-IAP
- Changing the W-IAP Installation Mode
- Changing USB Port Status
- Master Election and Virtual Controller
- Adding a W-IAP to the Network
- Removing a W-IAP from the Network
- VLAN Configuration
- IPv6 Support
- Wireless Network Profiles
- Configuring Wireless Network Profiles
- Configuring Fast Roaming for Wireless Clients
- Configuring Modulation Rates on a WLAN SSID
- Multi-User-MIMO
- Management Frame Protection
- Disabling Short Preamble for Wireless Client
- Editing Status of a WLAN SSID Profile
- Editing a WLAN SSID Profile
- Deleting a WLAN SSID Profile
- Wired Profiles
- Captive Portal for Guest Access
- Understanding Captive Portal
- Configuring a WLAN SSID for Guest Access
- Configuring Wired Profile for Guest Access
- Configuring Internal Captive Portal for Guest Network
- Configuring External Captive Portal for a Guest Network
- Configuring Facebook Login
- Configuring Guest Logon Role and Access Rules for Guest Users
- Configuring Captive Portal Roles for an SSID
- Configuring Walled Garden Access
- Authentication and User Management
- Managing W-IAP Users
- Supported Authentication Methods
- Supported EAP Authentication Frameworks
- Configuring Authentication Servers
- Understanding Encryption Types
- Configuring Authentication Survivability
- Configuring 802.1X Authentication for a Network Profile
- Enabling 802.1X Supplicant Support
- Configuring MAC Authentication for a Network Profile
- Configuring MAC Authentication with 802.1X Authentication
- Configuring MAC Authentication with Captive Portal Authentication
- Configuring WISPr Authentication
- Blacklisting Clients
- Uploading Certificates
- Roles and Policies
- DHCP Configuration
- Configuring Time-Based Services
- Dynamic DNS Registration
- VPN Configuration
- IAP-VPN Deployment
- Adaptive Radio Management
- Deep Packet Inspection and Application Visibility
- Voice and Video
- Services
- Configuring AirGroup
- Configuring a W-IAP for RTLS Support
- Configuring a W-IAP for Analytics and Location Engine Support
- Managing BLE Beacons
- Clarity Live
- Configuring OpenDNS Credentials
- Integrating a W-IAP with Palo Alto Networks Firewall
- Integrating a W-IAP with an XML API Interface
- CALEA Integration and Lawful Intercept Compliance
- Cluster Security
- W-IAP Management and Monitoring
- Uplink Configuration
- Intrusion Detection
- Mesh W-IAP Configuration
- Mobility and Client Management
- Spectrum Monitor
- W-IAP Maintenance
- Monitoring Devices and Logs
- Hotspot Profiles
- ClearPass Guest Setup
- IAP-VPN Deployment Scenarios
- Acronyms and Abbreviations
405 | IAP-VPN Deployment Scenarios Dell Networking W-Series Instant 6.5.1.0-4.3.1.0 | User Guide
Configuration Steps CLI Commands UI Procedure
(Instant AP)(DHCP profile "l3-dhcp")# domain-name
corpdomain.com
(Instant AP)(DHCP profile "l3-dhcp")# client-count
200
Local profile with VLAN 20
(Instant AP)(config)# ip dhcp local
(Instant AP)(DHCP profile "local")# server-type
Local
(Instant AP)(DHCP profile "local")# server-vlan 20
(Instant AP)(DHCP profile "local")# subnet
172.16.20.1
(Instant AP)(DHCP profile "local")# subnet-mask
255.255.255.0
(Instant AP)(DHCP profile "local")# lease-time 86400
(Instant AP)(DHCP profile "local")# dns-server
10.1.1.30,10.1.1.50
(Instant AP)(DHCP profile "local")# domain-name
arubanetworks.com
NOTE: The IP range configuration on each branch will be the
same. Each W-IAP will derive a smaller subnet based on the client
count scope using the Branch ID (BID) allocated by the controller.
5. Create authentication
servers for user
authentication. The
example in the next
column assumes 802.1X
SSID.
(Instant AP)(config)# wlan auth-server server1
(Instant AP)(Auth Server "server1")# ip 10.2.2.1
(Instant AP)(Auth Server "server1")# port 1812
(Instant AP)(Auth Server "server1")# acctport 1813
(Instant AP)(Auth Server "server1")# key
"presharedkey"
(Instant AP)(Auth Server "server1")# exit
(Instant AP)(config)# wlan auth-server server2
(Instant AP)(Auth Server "server1")# ip 10.2.2.2
(Instant AP)(Auth Server "server1")# port 1812
(Instant AP)(Auth Server "server1")# acctport 1813
(Instant AP)(Auth Server "server1")# key
"presharedkey"
See
Configuring an
External Server
for
Authentication
6. Configure wired port and
wireless SSIDs using the
authentication servers
and access rules; enable
authentication
survivability.
Configure wired ports to operate in NAT mode and associate
VLAN 20 to the wired port profile.
(Instant AP)(config) # wired-port-profile wired-port
(Instant AP)(wired-port-profile "wired-port")#
switchport-mode access
(Instant AP)(wired-port-profile "wired-port")#
allowed-vlan all
(Instant AP)(wired-port-profile "wired-port")#
native-vlan 20
(Instant AP)(wired-port-profile "wired-port")# no
shutdown
(Instant AP)(wired-port-profile "wired-port")#
access-rule-name wired-port
(Instant AP)(wired-port-profile "wired-port")# type
employee
(Instant AP)(wired-port-profile "wired-port")# auth-
server server1
See
Configuring a
Wired Profile
and Wireless
Network
Profiles
Table 86: W-IAP Configuration for Scenario 3—IPsec: Multiple Datacenter Deployment