Dell Studio™ 1435 Service Manual Before You Begin Base Cover Hard Drive Memory Wireless Mini-Cards Fan Processor Heat Sink Processor Center Control Cover Keyboard Palm Rest Optical Drive Speakers Audio Board Display Camera (Optional) Microphone Coin-Cell Battery System Board WiFi Sniffer Board Flashing the BIOS Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer.
Back to Contents Page Audio Board Dell Studio™ 1435 Service Manual Removing the Audio Board Replacing the Audio Board CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. Removing the Audio Board 1. Follow the instructions in Before You Begin.
Back to Contents Page Base Cover Dell Studio™ 1435 Service Manual Removing the Base Cover Replacing the Base Cover CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer. CAUTION: Before performing this procedures, turn off the computer, disconnect the AC adapter from the electrical outlet and the computer, disconnect the modem from the wall connector and the computer, and remove any other external cables from the computer.
Back to Contents Page Before You Begin Dell Studio™ 1435 Service Manual Recommended Tools Turning Off Your Computer Before Working Inside Your Computer This section provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist: l You have performed the steps in Turning Off Your Computer and Before Working Inside Your Computer. l You have read the safety information that shipped with your computer.
4. During installation or removal of any hardware, always ensure all data is backed up properly. 5. Disconnect any external peripherals and cable. 6. Disconnect all telephone or network cables from the computer. 7. Press and eject any installed cards from the ExpressCard slot and the 8-in--1 memory card reader. 8. Disconnect your computer and all attached devices from their electrical outlets.
Back to Contents Page Flashing the BIOS Dell Studio™ 1435 Service Manual Flashing the BIOS From a CD Flashing the BIOS From the Hard Drive If a BIOS-update program CD is provided with the new system board, flash the BIOS from the CD. If you do not have a BIOS-update program CD, flash the BIOS from the hard drive. Flashing the BIOS From a CD 1. Ensure that the AC adapter is plugged in and that the main battery is installed properly.
Back to Contents Page Camera (Optional) Dell Studio™ 1435 Service Manual Removing the Camera Replacing the Camera CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). Removing the Camera 1. Follow the instructions in Before You Begin. 2.
Back to Contents Page Center Control Cover Dell Studio™ 1435 Service Manual Removing the Center Control Cover Replacing the Center Control Cover CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
Replacing the Center Control Cover 1. Slide the media control buttons cable into the connector on the center control cover until it is in position and pull down on the connector latch that secures the cable to the connector. 2. Align the hooks beneath the center control cover and snap the cover in place. 3. Turn the computer over and replace the four screws that secure the center control cover to the computer base. 4. Slide the battery into the bay until it clicks into place.
Back to Contents Page Coin-Cell Battery Dell Studio™ 1435 Service Manual Removing the Coin-Cell Battery Replacing the Coin-Cell Battery CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
Back to Contents Page Processor Dell Studio™ 1435 Service Manual Removing the Processor Installing the Processor CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
When the processor is correctly seated, all four corners are aligned at the same height. If one or more corners of the processor are higher than the others, the processor is not seated correctly. NOTICE: To prevent intermittent contact between the ZIF-socket cam screw and the processor when removing or replacing the processor, press to apply slight pressure to the center of the processor while turning the cam screw. 2.
Back to Contents Page Processor Heat Sink Dell Studio™ 1435 Service Manual Removing the Processor Heat Sink Replacing the Processor Heat Sink CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). Removing the Processor Heat Sink 1.
Back to Contents Page
Back to Contents Page Display Dell Studio™ 1435 Service Manual Display Assembly Display Bezel Display Panel Display Panel Cable Inverter Board CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
1 display cable screw 2 camera cable pull-tab (optional) 3 power button cable connector 4 display cable pull-tab 11. Remove the two screws (one on each hinge). 12. Remove the display assembly. 1 display assembly 2 screw (2) Replacing the Display Assembly 1. Place the display assembly in position and replace the two screws. 2. Route the camera cable (optional), power button cable, and display cable through the routing guides and connect the cables to the respective system board connectors.
11. Slide the battery into the bay until it clicks into place. Display Bezel Removing the Display Bezel NOTICE: The display bezel is extremely fragile. Be careful when removing it to prevent damaging the bezel. 1. Follow the instructions in Removing the Display Assembly. 2. Using your fingertips, carefully pry up the inside edge of the display bezel. 3. Remove the display bezel. 1 display bezel Replacing the Display Bezel 1.
1 display panel screw (4) 2 inverter board screw (2) 3 inverter board 4 display panel 5. Remove the inverter board (see Removing the Inverter Board). 6. Remove the display panel assembly. 7. Remove the eight screws (four on either side)securing the display bracket. 1 screw (8 total; 4 on each side) 2 display panel bracket (1 left, 1 right) Replacing the Display Panel 1. Attach the display brackets to the display panel by replacing the eight screws (four on either side). 2.
2. Remove the display bezel (see Removing the Display Bezel). 3. Remove the display panel (see Removing the Display Panel). 4. Turn the display panel over and place it on a clean surface. 1 display cable 3 back of display panel 5. 2 securing clip (2) Press the securing clips on either side and disconnect the display cable from the connector on top. Replacing the Display Panel Cable 1. Connect the display cable to the connector on top. 2.
Replacing the Inverter Board 1. Connect the cables to the connectors on either side of the inverter board. 2. Replace the display panel along with the inverter board (see Replacing the Display Panel). 3. Replace the display bezel (see Replacing the Display Bezel). 4. Follow the instructions in Replacing the Display Assembly.
Back to Contents Page Fan Dell Studio™ 1435 Service Manual Removing the Fan Replacing the Fan CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). Removing the Fan 1. Follow the instructions in Before You Begin. 2.
Back to Contents Page
Back to Contents Page Hard Drive Dell Studio™ 1435 Service Manual Removing the Hard Drive Replacing the Hard Drive CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To prevent data loss, turn off your computer (see Turning Off Your Computer) before removing the hard drive.
1 hard drive 2 interposer 3 screw (4) 4 hard drive cage 6. Remove the four screws (two on either side) to detach the hard drive cage from the hard drive. 7. Lift the hard drive cage off the hard drive. Replacing the Hard Drive 1. Remove the new drive from its packaging. Save the original packaging for storing or shipping the hard drive. 2. Replace the four screws (two on either side) securing the hard drive cage to the hard drive. 3. Connect the interposer to the hard drive.
Back to Contents Page Keyboard Dell Studio™ 1435 Service Manual Removing the Keyboard Replacing the Keyboard CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
1 screw (2) 2 keyboard 3 keyboard tab (6) 4 connector latch 5 keyboard cable 7. Rotate the keyboard downward to expose the keyboard cable. 8. Release the connector latch that secures the keyboard cable to the connector on the system board and remove the cable. 9. Lift the keyboard off the computer. Replacing the Keyboard 1. Slide the keyboard cable into the connector on the system board and pull down on the connector latch that secures the keyboard cable to the system board.
Back to Contents Page Memory Dell Studio™ 1435 Service Manual Removing the Memory Module(s) Replacing the Memory Module(s) CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. You can increase your computer memory by installing memory modules on the system board. See "Specifications" in your Setup Guide for information on the memory supported by your computer. Install only memory modules that are intended for your computer.
1 tab 2 notch NOTICE: If the cover is difficult to close, remove the module and reinstall it. Forcing the cover to close may damage your computer. 3. Replace the base cover (see Replacing the Base Cover). 4. Slide the battery into the battery bay until it clicks into place or connect the AC adapter to your computer and an electrical outlet. 5. Turn on the computer. As the computer boots, it detects the additional memory and automatically updates the system configuration information.
Back to Contents Page Microphone Dell Studio™ 1435 Service Manual Removing the Microphone Replacing the Microphone CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. Removing the Microphone 1. Follow the instructions in Before You Begin. 2.
Back to Contents Page Wireless Mini-Cards Dell Studio™ 1435 Service Manual Removing the Mini-Card Replacing the Mini-Card CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the computer. NOTICE: Only a certified service technician should perform repairs on your computer.
5. Lift the Mini-Card out of the system board connector. NOTICE: When the Mini-Card is not in the computer, store it in protective antistatic packaging. For more information, see "Protecting Against Electrostatic Discharge" in the safety information that shipped with your computer. Replacing the Mini-Card 1. Remove the new Mini-Card from its packaging. NOTICE: Use firm and even pressure to slide the card into place. If you use excessive force, you may damage the connector. 2.
Back to Contents Page Optical Drive Dell Studio™ 1435 Service Manual Removing the Optical Drive Replacing the Optical Drive CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. Removing the Optical Drive 1.
Back to Contents Page Palm Rest Dell Studio™ 1435 Service Manual Removing the Palm Rest Replacing the Palm Rest CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. Removing the Palm Rest 1. Follow the instructions in Before You Begin. 2.
while pulling on the outside. 1 palm rest Replacing the Palm Rest 1. Align the palm rest with the computer base and gently snap the palm rest in place. 2. Connect the power sensor cable, touch pad cable, and fingerprint cable (optional) to the respective system board connectors. 3. Replace the screws on the top of the palm rest. 4. Turn the computer over and replace the eleven screws in the computer base. 5. Replace the keyboard (see Replacing the Keyboard). 6.
Back to Contents Page Speakers Dell Studio™ 1435 Service Manual Removing the Speakers Replacing the Speakers CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. Removing the Speakers 1. Follow the instructions in Before You Begin. 2.
4. Connect the display cable to the connector on the system board. 5. Replace the screw that secures the display cable. 6. Replace the optical drive (see Replacing the Optical Drive). 7. Replace the palm rest (see Replacing the Palm Rest). 8. Replace the keyboard (see Replacing the Keyboard). 9. Replace the center control cover (see Replacing the Center Control Cover). 10. Replace the base cover (see Replacing the Base Cover). 11. Slide the battery into the bay until it clicks into place.
Back to Contents Page System Board Dell Studio™ 1435 Service Manual Removing the System Board Replacing the System Board CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
4. Connect the speaker cable to the system board connector (see Replacing the Speakers). 5. Replace the palm rest (see Replacing the Palm Rest). 6. Replace the keyboard (see Replacing the Keyboard). 7. Replace the center control cover (see Replacing the Center Control Cover). 8. Replace the processor heat sink and processor (see Replacing the Processor Heat Sink and Installing the Processor). 9. Replace the hard drive (see Replacing the Hard Drive). 10.
Back to Contents Page WiFi Sniffer Board Dell Studio™ 1435 Service Manual Removing the WiFi Sniffer Board Replacing the WiFi Sniffer Board Removing the WiFi Sniffer Board 1. Follow the instructions in Before You Begin. 2. Remove the center control cover (see Removing the Center Control Cover). 3. Remove the keyboard (see Removing the Keyboard). 4. Remove the palm rest (see Removing the Palm Rest). 5. Remove the screw on WiFi sniffer board. 1 WiFi sniffer board 2 screw 6.
2. Connect the WiFi sniffer board cable to the system board connector. 3. Replace the palm rest (see Replacing the Palm Rest). 4. Replace the keyboard (see Replacing the Keyboard). 5. Replace the center control cover (see Replacing the Center Control Cover). 6. Replace the base cover (see Replacing the Base Cover). 7. Slide the battery into the bay until it clicks into place.
