Dell EMC SmartFabric OS10 System Log Message Reference Guide Release 10.5.2 June 2021 Rev.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2016 - 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents Chapter 1: Revision history............................................................................................................6 Chapter 2: About this guide...........................................................................................................7 Audience.................................................................................................................................................................................7 Conventions................................
Chapter 18: EVPN system log message reference........................................................................ 37 Chapter 19: FC_SVCS system log message reference.................................................................. 38 Chapter 20: FCOE system log message reference........................................................................40 Chapter 21: FEFD system log message reference.........................................................................
Chapter 41: RAGUARD_EVENT system log message reference.................................................... 66 Chapter 42: RAGUARD system log message reference................................................................. 67 Chapter 43: Routemap with match ACL system log message reference....................................... 68 Chapter 44: Scale VLAN profile system log message reference....................................................
1 Revision history This table provides an overview of the changes in this guide. Table 1. Revision history Release Revision Description 10.5.2.
2 About this guide This guide is intended for system administrators who are responsible for configuring and maintaining networks. It covers the following details: ● Information on system events and alarms. ● Lists the System log messages corresponding to various protocols and services that are generated by SmartFabric Dell EMC OS10. ● Provides Description for each System log message and the Recommended action that you can take to mitigate the System log message.
Related Documents Dell EMC SmartFabric OS10 is part of various networking solution deployments including PowerEdge MX, VxRail, and so on. The following tables list all the available documentation for Dell EMC SmartFabric OS10. Table 2. SmartFabric OS10 Documentation Related Documentation Description Link Dell EMC SmartFabric OS10 Documentation.
3 System log messages overview This chapter provides an overview of the system log messages supported in Dell EMC SmartFabric OS10. Topics: • • • System events and alarms System logging over TLS View system logs System events and alarms An event notifies you of a change or situation in the system that you might be interested in. An alarm indicates that the system has entered an abnormal state and may require immediate action.
Configure custom severity profile To modify the severity of events or disable event notification: Your user account must have any one of the following privileges: System admin (sysadmin), security admin (secadmin), or network admin (netadmin). 1. Use the dir command to view the list of available severity profiles in the severity-profile:// partition.
5. Apply the custom severity profile on the switch. OS10# event severity-profile mySevProf_1.xml NOTE: You must restart the switch for the changes to take effect. 6. Restart the switch. OS10# reload 7. Use the show event severity-profile command to view the custom profile that is active. OS10# show event severity-profile Severity Profile Details -------------------------------------------Currently Active : default Active after restart : mySevProf_1.
The certificate-key pair is installed as Dell_host1.pem and Dell_host1.key. In configuration commands, refer to the pair as Dell_host1. When you configure a security profile, you would enter Dell_host1 in the certificate certificate-name command. ● For security reasons, because the key file contains private key information, it copied to a secure location in the OS10 file system and deleted from its original location specified in the key-file key-path parameter.
OS10# copy home://clientreq.pem scp://CAadmin:secret@172.11.222.1/clientreq.pem OS10# copy scp://CAadmin:secret@172.11.222.1/clientcert.pem home://clientcert.pem OS10# copy scp://CAadmin:secret@172.11.222.1/clientkey.pem home://clientkey.pem OS10# crypto cert install cert-file home://clientcert.pem key-file home://clientkey.pem Processing certificate ... Certificate and keys were successfully installed as "clientcert.crt" that may be used in a security profile. CN = 10.0.0.
notice:USB_DEVICE_INSERTED: Vendor: Linux_3.16.39_ehci_hcd Product: EHCI_Host_Controller Serial: 0000:00:16.0 Jan 4 19:13:17 OS10 usb_monitor: Node.1-Unit.1:PRI:notice %Dell EMC (OS10) %lognotice:USB_DEVICE_INSERTED: Vendor: 8087 Product: 07db Serial: unknown Jan 4 19:13:18 OS10 dn_dot1x[900]: Node.1-Unit.1:PRI:notice [os10:trap], %Dell EMC (OS10) %log-notice:DOT1X_PDU_RX_FAIL: PDU Reception Failed Kernel Index 1 Jan 4 19:13:20 OS10 dn_etl[917]: Node.1-Unit.
4 ACL system log message reference This section lists the messages that are generated by the ACL process. Table 3. OS10 ACL system log messages System log message Severity Description Recommended action %ROUTE_MAP_MATCH_PARA M: Route-map Informational Match address based on ACL is not applicable for Routing modules in VRF ." No action required. %ACL_TABLE_FULL: ACL table full Informational The ACL TCAM space is of fixed size based on each platform.
Table 3. OS10 ACL system log messages (continued) System log message 16 Severity ACL system log message reference Description Recommended action that logging cannot be done in the egress ACL. matching rules will not be displayed.
5 AFS system log message reference This section lists the messages that are generated by the AFS process. Table 4. OS10 AFS system log messages System log message Severity Description Recommended action % INFRA_AFS:MAC_MOVE_VIOLA TION original-ifname ethernet1/1/1,offending-ifname ethernet1/1/2,MAC 00:00:00:00:00:10,vlan 10 Informational When port security is configured, MAC move violation occurs from secure port eth 1/1/1 to secure port eth 1/1/2, Port security violation.
6 ALM_ACCNT_MAC system log message reference This section lists the system log messages generated by the ALM_ACCNT_MAC process. Table 5. ALM_ACCNT_MAC system log messages System log message Severity Description Recommended action %ALM_ACCNT_EVENT: Accounting event was raised Informational Information about session details during user login. When AAA accounting is configured, these logs will be seen for each user during login. No action required.
7 ALM_CLOCK system log message reference This section lists the system log messages generated by the ALM_CLOCK process. Table 6. ALM_CLOCK system log messages System log message Severity Description Recommended action %ALM_CLOCK_UPDATE: Clock changed Informational The System clock is changed. ALM_CLOCK_UPDATE: Clock changed No action required.
8 BFD system log message reference This section lists the system log messages generated by the BFD process. Table 7. BFD system log messages System log message Severity Description Recommended action %BFD_STATE_CHANGE: Session state to Informational Session state has changed for a BFD session. No action required.
9 BGP system log message reference This section lists the system log messages that are generated by the BGP process. Table 8. BGP system log messages System log message Severity Description Recommended action %BGP_NBR_NOTIFY_EST_STAT Informational E: BGP FSM established state change Notification BGP session successfully established with configured peer. BGP peering successful. No action required. %BGP_NBR_BKWD_STATE_CH G: Backward state change occurred Critical Configured BGP session went down.
Table 8. BGP system log messages (continued) System log message Severity Description Recommended action connectivity lost/fall-over for Nbr over:%s VRF:%s" NOTE: VRF %s denotes VRF Nbr:%s denotes Nbr IP or unnumbered peer interface name %BGP_NBR_BKWD_STATE_CH G: Backward state change occurred OPEN ERR: %s Critical Connection with BGP neighbor is Check the connectivity and closed due to error in one of the contact Technical Support, if attributes/options received in OPEN required. message.
Table 8. BGP system log messages (continued) System log message Severity Description Recommended action "BAD UPD msg rcvd from Nbr over:%s VRF:%s" 13. "Update err rcvd from Nbr over:%s VRF:%s" NOTE: VRF %s denotes VRF Nbr:%s denotes Nbr IP or unnumbered peer interface name %BGP_NBR_BKWD_STATE_CH G: Backward state change occurred HEADER ERROR:%s Critical Connection with BGP neighbor is Contact Support team with closed due to error in HEADER of the error log. the message received.
Table 8. BGP system log messages (continued) System log message Severity Description Recommended action 8. "Router-id changed Nbr over:%s VRF:%s recycled" 9. "Invalid martian next hop for Nbr over:%s VRF:%s" 10. "Attribute len error for Nbr over:%s VRF:%s" 11."BFD Nbr over:%s VRF:%s DOWN" 12. "ADDPATH Denied Nbr over:%s VRF:%s" NOTE: VRF %s denotes VRF Nbr:%s denotes Nbr %BGP_MAX_PRFX_REACHED: Maximum prefix limit per peer exceeded.
Table 8. BGP system log messages (continued) System log message Severity Description Recommended action peer list has unnumbered neighbor." 7. "PGR and PEER Area Mismatch Config " 8. "Unnum PGR with ebgp-multihop configured when peer list has unnumbered neighbor." 9. "Unnum PGR with fallover configured when peer list has unnumbered neighbor." 10. "Unnum PGR with routereflector-client configured when peer list has unnumbered neighbor." 11.
10 CMS system log message reference This section lists the system log messages that the CMS process generates. Table 9. CMS system log messages System log message Severity Description Recommended action %CMS_INIT_STATE: init state Informational The log indicates the new state, the CMS module is transitioning to. On system boot, the CMS should eventually transition to state 6. Transitioning to state 6 indicates successful initialization of the CMS module.
11 Configuring LLFC system log message reference This section lists the system log message for configuring LLFC on discovery ports from OS10 release 10.5.2.3. Table 10. Configuring LLFC System log message Severity LLFC_ON_ICL_DISCOVERY_POR Informational T : LLFC enabled on ICL discovery port Description Recommended action This system log message is generated when the user configures LLFC on discovery ports and vice-versa. No action required.
12 DCBX system log messages This section lists the system log messages that the DCBX process generates. Table 11. DCBX system log messages System log message Severity Description Recommended action %DCBX_PFC_PORT_OPER_UP: Informational PFC Parameters MATCH on interface PFC configuration of remote port matches local PFC configuration. No action required.
13 DENIED_ARP system log message reference This section lists the system log messages that are generated by the DENIED_ARP process. Table 12. DENIED_ARP system log messages System log message Severity Description Recommended action %DENIED_ARP_PACKET: DAI:Denied ARP packet Informational The ARP packets denied by Dynamic ARP inspection as this ARP packet does not match the DAI rules and dropped.
14 DOT1X system log message reference This section lists the system log messages that are generated by the DOT1X process. Table 13. DOT1X system log messages System log message Severity Description Recommended action %DOT1X_PDU_TX_FAIL: PDU Transmission Failed Informational PDU Transmission Failed. If the message is displayed document the message exactly as it appears and contact your technical support representative for assistance.
15 DYNAMIC_MGMT system log message reference This section lists the system log messages that are generated by the DYNAMIC_MGMT process. Table 14. DYNAMIC_MGMT system log messages System log message Severity %DYNAMIC_MGMT_ROUTE_OV Informational ERWRITE: Overriding route obtained via DHCP/Autoconf with static route. Description Recommended action Route configured is overridden by route via No action required. DHCP/AutoConf.
16 EQM system log message reference This section lists the system log messages that are generated by the EQM process. Table 15. EQM system log messages System log message Severity Description Recommended action %EQM_UNIT_UP: Unit is up Informational Equipment Manager declared the card is ready. No action required. %EQM_UNIT_DOWN: Unit is down Critical Equipment Manager detected the card is reset. No action required.
Table 15. EQM system log messages (continued) System log message Severity Description Recommended action %EQM_TML_MINOR_CROSSED Warning : Thermal threshold crossed minor warning One of the temperature sensors has crossed the "Minor Threshold". Check the environment, for example, faulty fan tray, and fix them. The fans speeds will increase automatically. %EQM_TML_MAJOR_CROSSED Critical : Thermal threshold crossed major warning One of the temperature sensors has crossed the "Minor Threshold".
Table 15. EQM system log messages (continued) System log message Severity Description Recommended action %EQM_MEDIA_NOT_PRESENT: Media removed Critical A media(port) is removed. If not expected, check whether the media is properly inserted. %EQM_MEDIA_QSA28_EXPECT Critical ED: QSA28 adapter expected The platform expects a QSA28 adapter, but the inserted optics is not QSA28. Check the media adapter connected to the port.
Table 15. EQM system log messages (continued) System log message Severity Description Recommended action %EQM_MEDIA_VOLTAGE_LOW _WARNING: Media low warning voltage threshold crossed minor warning Warning Digital Optical Monitoring detects that the low voltage minor threshold is crossed. Check whether the media is supported. Try replacing the media.
17 ETL system log message reference This section lists the system log messages that are generated by the ETL process. Table 16. ETL system log messages System log message Description Recommended action %ETL_SERVICE_UP: ETL service Informational is up Event Logger Service is up. ETL service is up. No action required. %ETL_HOST_UNREACHABLE: Destination host unreachable Informational Logging Server is unreachable. Destination host unreachable. Check logging server connectivity to the system.
18 EVPN system log message reference This section lists the system log messages that are generated by the EVPN process. Table 17. EVPN system log messages System log message Severity Description Recommended action %EVPN_MAC_ERROR: EVPN MAC error: Informational System detects 5 mac station move between VTEPs with in 3 min. EVPN MAC %s error %s for MAC %s Without any user action, VMs move between VTEPs, check for any duplicate MACs present in the VMs.
19 FC_SVCS system log message reference This section lists the system log messages that are generated by the FC_SVCS process. Table 18. FC_SVCS system log messages System log message Severity Description Recommended action %FC_SVCS_MS_START_FABRI C_RECONFIG: The Switch Starts Informational This log is displayed in Multi-switch mode, where any link failure in the fabric that may result in Build Fabric operation causing the Principal switch re-election.
Table 18. FC_SVCS system log messages (continued) System log message Severity Description Recommended action teared down sessions get logged in successfully within the 30 second time period. After that if there is any state change deducted like enode logged out or uplink going down then this log is raised. %FC_SVCS_NPG_SLB_NOT_SU Informational CCESS: Re-balance This log is raised when the operations got timed-out (30 seconds) for the Vfabric-ID. i.e the sessions did not relogin.
20 FCOE system log message reference This section lists the system log messages that are generated by the FCOE process. Table 19. FCOE system log messages System log message Description Recommended action %FCOE_RECV_PACKET_ERROR Critical : Packet Receive Error This error message appears when the FCOE application deletes the FIP deny ACL rule during port transitioning to Operation Up state. If an FIP packet is received during this time, it is dropped.
Table 19. FCOE system log messages (continued) System log message Severity Description Recommended action %FCOE_CONFLICT_VLAN: FIP Snooping conflict in FCF advertised VLAN. FIP snooping not enabled for this VLAN Critical FCOE VLAN is different from the FCF advertised VLAN. Configure same FCOE VLAN on all the switches, that is, FSB or NPG and F-port. %FCOE_SESSION_UPDATE: FCoE Session Informational This log is displayed when a new FCOE session is created or an existing FCOE sesssion is cleared.
21 FEFD system log message reference This section lists the system log messages that are generated by the FEFD process. Table 20. FEFD system log messages System log message Severity Description Recommended action %FEFD_OUT_OF_MEM: FEFD: Out of Memory Informational The system is running out of memory. System is out of memory. Reduce processes if possible. Contact your technical support representative for further analysis.
22 IGMP system log message reference This section lists the system log messages that are generated by the IGMP process. Table 21. IGMP system log messages System log message Severity Description Recommended action %IGMP_SNOOPING_INTERFACE Informational : IGMP Snooping IGMP snooping is configured on a default VLAN, hence it is operationally disabled. IGMP_SNOOPING_INTERFACE: IGMP Snooping disabled on interface :%s No action required. IGMP or MLD Snooping instance Informational limit exceeded.
23 IP system log message reference This section lists the system log messages that are generated by the IP system process. Table 22. IP system log messages System log message Severity Description Recommended action %IP_ADDRESS_ADD: IP Address add is successful. Informational IP Address Addition. No action required. %IP_ADDRESS_DEL: IP Address delete is successful. Informational IP Address Deletion. No action required.
24 IPv6 system log message reference This section lists the system log messages that are generated by the IPv6 process. Table 23. IPv6 system log messages System log message Severity Description Recommended action IPv6 Extended Prefix support not Informational configured Unable to program routes with prefix length > 64 and < 128. Configure IPv6-extended support and hardware Layer3 IPv6-extended-prefix and reboot the system. You must configure these settings globally.
25 ISCSI system log message reference This section lists the system log messages that are generated by the ISCSI process. Table 24. ISCSI system log messages System log message Severity Description Recommended action %ISCSI_GLB_ENABLE: ISCSI_OPT: ISCSI Globally enabled. Trigger Auto-config Informational Indicates the configuration of iSCSI Auto-config has been successful. Configurations are going on. No action required. %ISCSI_GLB_DISABLE: ISCSI_OPT: ISCSI Globally disabled.
Table 24. ISCSI system log messages (continued) System log message Severity Description Recommended action disabled. Until then they are ignored with this log. %ISCSI_APP_TLV: ISCSI_OPT Informational Logs on Application TLV to indicate priority on which iSCSI is enabled. No action required.
26 LACP system log message reference This section lists the system log messages that are generated by the LACP process. Table 25. LACP system log messages System log message Severity Description Recommended action %LACP_PORT_GROUPED: Interface joined port-channel Informational Port got grouped to port channel. No action required. %LACP_PORT_UNGROUPED: Interface exited port-channel Informational Port got ungrouped from port channel. No action required.
27 LADF system log message reference This section lists the system log messages that are generated by the LADF process. Table 26. LADF system log messages System log message Severity Description Recommended action %LADF_STAG_NOT_FOUND: System service tag not found. Critical Service Tag not found. Contact your technical support representative for further assistance. %LADF_LIC_FILE_NOT_FOUND: Critical License file not present.
28 LB system log message reference This section lists the system log messages that are generated by the LB process. Table 27. LB system log messages System log Message Severity Description Recommended action %LB_UNEVEN_DISTR: Uneven distribution in link bundle Informational Uneven distribution in link bundle. This System log message is seen when traffic distribution on a monitored link is unfairly distributed at given time.
29 LLDP system log message reference This section lists the system log messages that are generated by the LLDP process. Table 28. LLDP system log messages System log message Severity Description Recommended action %LLDP_VIRTUAL_IPV4: LLDP:Virtual IPv4 address Informational Displays the virtual ipv4 address. No action required. %LLDP_VIRTUAL_IPV6: LLDP:Virtual IPv6 address Informational Displays the virtual ipv6 address. No action required.
30 MGMT_CLISH system log message reference This section lists the system log messages that are generated by the MGMT_CLISH process. Table 29. MGMT_CLISH system log messages System log message Severity Description Recommended action %MGMT_CLISH_CMD_AAA_AU THOR: Cmd Authorization failed. Warning You are restricted to configure this command with the current user role.
31 SYSTEM_MODE_CHANGE system log message reference This section lists the system log messages that are generated by the SYSTEM_MODE_CANGE process. Table 30. SYSTEM_MODE_CANGE system log messages System log message Severity Description Recommended action %SYSTEM_MODE_CHNG: system mode changed : Informational Switch operating mode is changed by No action required. user. Switch operating mode options are Full-Switch and Smart-Fabric Director.
32 MLD system log message reference This section lists the system log messages that are generated by the MLD process. Table 31. MLD system log messages System log message Description Recommended action %MLD_SNOOPING_INTERFACE: Informational MLD Snooping MLD snooping is configured on a default VLAN, hence it is operationally disabled. MLD_SNOOPING_INTERFACE: MLD Snooping disabled on interface :%s No action required. IGMP or MLD Snooping instance limit receded.
33 NDM system log message reference This section lists the system log messages that are generated by the NDM process. Table 32. NDM system log messages System log message Severity Description Recommended action %NDM_SYSTEM_RELOAD: User request to reload system Informational You will see this message if you have run the reload command. No action required. %NDM_SPEED_MISMATCH: VLTi member speed doesn't match.
34 PBR match access-list system log message reference This section lists the system log messages that are generated by the PBR match access-list. Table 33. PBR match access-list System log message Description Recommended action Match access-list not found in the Informational route-map This system log message is generated when you try to attach an interface for policy based routing to a route map without match access-list criteria. No action required.
35 OPEN_FLOW system log message reference This section lists the system log messages that are generated by the OPEN_FLOW process. Table 34. OPEN_FLOW system log messages System log message Severity Description Recommended action %OPENFLOW_TABLE_FULL: Openflow table is full : Table ID Informational OpenFlow table is full. If the table full is not expected, document the message exactly as it appears and contact your technical support representative for assistance.
36 OSPFv2 system log message reference This section lists the system log messages that are generated by the OSPFv2 process. Table 35. OSPFv2 system log messages System log message Severity Description Recommended action %OSPFV2_ADJ_CHANGE: OSPF Process Informational The OSPFv2 session state changes from one state to other state. OSPF Process VRF %s %d, Nbr %s on %s state changed to %s No action required.
Table 35. OSPFv2 system log messages (continued) System log message Severity Description Recommended action %OSPFV2_OPTION_MISMATCH: Informational OSPF detected option mismatch This indicates there is a mismatch in type of area configuration. OSPF detected option mismatch VRF %s from %s on interface %s Check and configure the same area type for OSPFv2 neighbors.
37 OSPFv3 system log message reference This section lists the system log messages that are generated by the OSPFv3 process. Table 36. OSPFv3 system log messages System log message Severity Description Recommended action %OSPFV3_ADJ_CHANGE: OSPFv3 Process Informational The OSPFv3 session state changes from one state to other state. OSPFv3 Process VRF %s %d, Nbr %s on %s state changed to %s No action required.
Table 36. OSPFv3 system log messages (continued) System log message Severity Description Recommended action oper/admin down. Also possible failure in socket creation. OSPF detected neighbor admin down VRF %s from %s on interface %s is a socket failure, try to unconfigure and configure again OSPFv3. If the problem is not resolved reboot the system. If the underlying OSPF interface is admin/ oper down try to activate interface.
38 PIM system log message reference This section lists the system log messages that are generated by the PIM process. Table 37. PIM system log messages System log message Severity Description Recommended action %PIM_ROUTE: IIF Mismatch For Informational There is a mismatch on the incoming interface of a route learnt on the VLT nodes. PIM_ROUTE: IIF Mismatch For SRC: %s GRP: %s,Local IIF %s & Peer IIF %s for VRF: %s Occurred Check the PIM interface and VRF level configuration on both the nodes.
39 PTP system log message reference This section lists the system log messages that are generated by the PTP process. Table 38. PTP system log messages System log message Severity Description Recommended action %PTP_CLOCK_PHASE_LOCKED : Clock servo is phase locked. Informational Lock status of the clock is phase No action required. locked with master. This means that the offset with the master is within the default range of +/- 1 micro seconds. Lock status of the clock is phase locked with master.
Table 38. PTP system log messages (continued) System log message Severity Description Recommended action service is started and would update the system time at regular intervals. %PTP_SYSTEM_TIME_UPDATE _STOPPED: System time update service is stopped. 64 Informational PTP system log message reference Indicates that the system time update service is stopped. This happens either upon config change or lock status change. Indicates that the system time update service is stopped.
40 QoS system log message reference This section lists the system log messages that are generated by the QoS process. Table 39. QoS system log messages System log message Severity Description Recommended action %QOS_PFC_SERVICE_POLICY: Pfc service policy: Warning When a network qos policy, which has Priority Flow Control enabled is attached to an interface having Link Level Flow Control (LLFC) receive or transmit enabled, the system log is generated. The system log is not being used.
41 RAGUARD_EVENT system log message reference This section lists the system log messages that are generated by the RAGUARD_EVENT process. Table 40. RAGUARD_EVENT system log messages System log message Severity %RAGUARD_DENIED_RA_PACK Informational ET: RAGUARD: Denied RA Packet 66 Description Recommended action Received Router Advertisement packet is dropped because of policy mismatch. RAGuard policy can be configured to prevent attacks based on RA messages.
42 RAGUARD system log message reference This section lists the system log messages that are generated by the RAGUARD process. Table 41. RAGUARD system log messages System log message Severity Description Recommended action % RAGUARD Informational IPv6 RA Guard is enabled on the interface, so BGP unnumbered configuration on the same will not work. It indicates that RA Guard is enabled on the interface where BGP unnumbered session is up.
43 Routemap with match ACL system log message reference This section lists the system log message for route-map with match ACL when added to routing protocol per VRF from OS10 release 10.5.2.3. Table 42. Routemap with match ACL System log message Severity Description Route-map : Match address based on ACL is not applicable for Routing modules in VRF . Informational This system log message is generated No action required.
44 Scale VLAN profile system log message reference This section lists the system log message for Scale VLAN Profile and L3 configuration when L3 mode is not configured from OS10 release 10.5.2.3. Table 43.
Table 43. Scale VLAN profile (continued) System log message Severity Description Recommended action Scale VLAN profile, which is globally enabled and L3 mode is not configured. VLAN profile. For more information on configuring scaled VLAN profile, see https://www.dell.
Table 43. Scale VLAN profile (continued) System log message Severity Description Recommended action see https://www.dell.
45 Static and dynamic route system log message reference This section lists the system log message for static and dynamic route with prefix greater than 64 and less than 128 when the IPv6 extended prefix is not configured from OS10 release 10.5.2.1. Table 44. Static and dynamic route System log message Severity Description Recommended action IPv6 Extended Prefix support not configured - Unable to program routes with prefix length greater than 64 and less than 128.
46 SA system log message reference This section lists the system log messages that are generated by the SA process. Table 45. SA system log messages System log message Severity Description Recommended action %SUPPORTASSIST_SERVICE_U P: Support Assist Service up Informational Support Assist Service is enabled by the user. No action required. %SA_ACTI_FULL_XFER_SUCCE SS: Support Assist Full Transfer completed successfully Informational Uploaded the complete bundle to support assist server.
47 STATIC_MGMTsystem log message reference This section lists the system log messages that are generated by the STATIC_MGMT process. Table 46. STATIC_MGMT system log messages System log message Severity Description Recommended action %STATIC_MGMT_ROUTE_OVE RWRITE: Overriding static route with route obtained via DHCP/ Autoconf. Informational Static Route configured is overridden by route via DHCP/AutoConf. No action required.
48 STP system log message reference This section lists the system log messages that are generated by the STP process. Table 47. STP system log messages System log message Severity Description Recommended action %STP_BPDU_GUARD_ERR: STP: BPDU received on BPDU guard enabled port. Informational The spanning-tree bpduguard enable command is configured on an interface(s) and OS10 is reporting that the interface received a BPDU. The interface is brought down and placed in ERR_DISABLE mode.
49 UFD system log message reference This section lists the system log messages that are generated by the UFD process. Table 48. UFD system log messages System log message Severity Description Recommended action %UFD_ERROR_SET: Interface set to UFD Error : Informational This log is displayed when the downstream interface is set to disabled due to upstream interfaces going down. No action required.
50 USER_ROLE_CHANGED system log message reference This section lists the system log messages that are generated by the USER_ROLE_CHANGED process. Table 49. USER_ROLE_CHANGED system log messages System log message Severity Description Recommended action %USER_ROLE_CHANGE: User role changed. Informational Information to user about user role change(helpful when user role is modified in remote authentication servers). Informational. No action required.
51 Delay restore port system log message reference This section lists the system log messages that are generated by the Delay restore port process. Table 50. Delay restore port system log messages System log message Severity Description Recommended action %DELAY_RESTORE_PORT_STA RT: Delay restore port timer start Informational Indicates that delay restore timer has started for ports after reload. Delay restore port is used for nonVLT deployments.
52 VLT system log message reference This section lists the system log messages that are generated by the VLT process. Table 51. VLT system log messages System log message Severity Description Recommended action %VLT_ELECTION_ROLE: VLT Informational Indicates that VLT node(s) in a No action required. VLT domain elected a role. Local and remote VLT nodes can be distinguished using a unit number present in the system log.
Table 51. VLT system log messages (continued) System log message Severity Description Recommended action appear on the console, detected for unit %u. Here unit represents the VLT peer unit id. After the detection of VLT MAC mismatch, If user configures the same MAC in the other VLT peer as well, following system log will appear cleared for unit %u %VLT_PORT_CHANNEL_UP: vlt-port-channel Informational VLT port-channel is operationally UP in one of the VLT peers. vlt-portchannel %d is up.
Table 51. VLT system log messages (continued) System log message Severity Description Recommended action state. If the VLT lag it is put in error disabled state the following message appears: VLT port 10 is put in errordisabled state pending egress mask installation in remote peer. If the VLT lag recovers from the error-disabled state, then the following message appears: VLT port 10 recovered from error-disabled state.
53 VRF system log message reference This section lists the system log messages that are generated by the VRF process. Table 52. VRF system log messages System log message Severity Description Recommended action %VRF_CREATE: VRF Creation is successful. Informational VRF Creation. No action required. %VRF_DELETE: VRF Deletion is successful. Informational VRF Deletion. No action required.
54 VXLAN system log message reference This section lists the system log messages that are generated by the VXLAN process. Table 53. VXLAN system log messages System log message Severity Description Recommended action %VXLAN_OVERLAY_ECMP_PROFIL Informational E_MODIFIED: VxLAN Overlay ECMP: Hardware overlay-ecmp-profile mode configuration is changed. Configuration is modified, Save and Reload the device for the profile to be effective. To take effect, system configurations should be saved and reloaded.
55 IFM system log message reference This section lists the system log messages that are generated by the IFM process. Table 54. IFM system log messages System log message Severity Description Recommended action %IFM_OSTATE_UP: Interface operational state is up Informational Interface operational status is up. No action required. %IFM_OSTATE_DN: Interface operational state is down Informational Interface operational status is down. No action required.
Index R revision history 6
