Dell PowerEdge C4130 Owner's Manual Regulatory Model: E32S Series Regulatory Type: E32S001
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2015 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
Contents 1 About the PowerEdge C4130 system................................................................8 Supported configurations on PowerEdge C4130 systems..................................................................8 Customer and field replaceable units...................................................................................................9 Front panel features and indicators....................................................................................................
Entering Boot Manager ................................................................................................................ 35 Boot Manager main menu............................................................................................................ 35 Changing the boot order....................................................................................................................36 Choosing the system boot mode.....................................................................
Installing a heat sink...................................................................................................................... 70 System battery..................................................................................................................................... 72 Replacing the system battery........................................................................................................72 PCIe shroud.......................................................................
Installing the cable routing clip.................................................................................................. 109 System board..................................................................................................................................... 110 Removing the system board....................................................................................................... 110 Installing the system board..................................................................
Troubleshooting a damaged system................................................................................................156 Troubleshooting the system battery.................................................................................................157 Troubleshooting power supply units............................................................................................... 158 Troubleshooting power source problems..........................................................................
1 About the PowerEdge C4130 system The Dell PowerEdge C4130 rack servers support up to: • Two Intel Xeon E5-2600 v3 processors • Sixteen DIMMs • Four 2.5 inch hard drives (optional) • Two 1.8 inch solid state drives (SSDs) • Two power supply units (PSUs) • Four graphics processing units (GPUs) NOTE: All GPU cards must be of the same type and model. Mixing GPUs is not supported. NOTE: The PSU 2 slot also functions as the optional 2.5 inch hard drive cage slot. If you install the optional 2.
PowerEdge C4130 systems Configuration type Description Expansion card Expansion slot 1 card slot 2 H Supports three GPUs but does not support a GPU switch board. x8 x8 I Supports three GPUs but does not support a GPU switch board. x8 Not supported NOTE: Incorrect removal and installation of the GPUs will cause operational issues to your system.
• Control panel module Front panel features and indicators Figure 1. Front panel features and indicators Item Indicator, button, or connector 1 Health indicator Icon Description Indicates the health of the system. • • If the system is on and in good health, the indicator lights solid blue. No corrective action is required. The indicator blinks amber if the system is on or in standby, and if any error exists (for example, a failed fan).
Item Indicator, button, or connector Icon Description the back flashes until one of the buttons is pressed again. Press the system identification button to turn the system ID on or off. If the system stops responding during POST, press and hold the system ID button for more than five seconds to enter BIOS progress mode. To reset iDRAC (if not disabled in F2 iDRAC setup), press and hold the button for more than 15 seconds.
Item Indicator, button, or connector Icon Description To reset iDRAC (if not disabled in F2 iDRAC setup), press and hold the button for more than 15 seconds. 2 NMI button Used to troubleshoot software and device driver errors when running certain operating systems. This button can be pressed using the end of a paper clip. Use this button only if directed to do so by qualified support personnel or by the operating system documentation. 3 iDRAC8 Enterprise port Dedicated management port.
NIC indicator codes Figure 3. NIC indicators 1. link indicator 2. activity indicator Convention Indicator pattern Description A Link and activity indicators are OFF The NIC is not connected to the network. B Link indicator is green The NIC is connected to a valid network at its maximum port speed (1 Gbps). C Link indicator is yellow The NIC is connected to a valid network at less than its maximum port speed. D Activity indicator is blinking green Network data is being sent or received.
uSATA SSD indicator codes Figure 4. uSATA SSD indicators 1. uSATA SSD activity indicator 3. uSATA SSD 2. uSATA SSD status indicator NOTE: If the SSD is in Advanced Host Controller Interface (AHCI) mode, the status indicator (on the right side) does not function and remains off. Drive-status indicator pattern Condition Blinks green two times per second Identifying drive or preparing for removal. Off Drive ready for insertion or removal.
Figure 5. AC PSU status indicator 1. AC PSU status indicator/handle Convention Power Indicator Pattern Description A Green A valid power source is connected to the PSU and the PSU is operational. B Flashing green When the firmware of the PSU is being updated, the PSU handle flashes green. CAUTION: Do not disconnect the power cord or unplug the PSU when updating firmware. If firmware update is interrupted, the PSUs will not function.
Convention Power Indicator Pattern Description CAUTION: When correcting a PSU mismatch, replace only the PSU with the flashing indicator. Swapping the other PSU to make a matched pair can result in an error condition and unexpected system shutdown. To change from a High Output configuration to a Low Output configuration or vice versa, you must power down the system. CAUTION: AC PSUs support both 220 V and 110 V input voltages with the exception of Titanium PSUs, which support only 220 V.
To... Refer to... Use Lifecycle Controller Remote Services Dell Lifecycle Controller Remote Services Quick Start Guide at dell.com/esmmanuals Set up, use, and troubleshoot OpenManage Server Administrator Dell OpenManage Server Administrator User’s Guide at dell.com/openmanagemanuals Install, use, and troubleshoot OpenManage Essentials Dell OpenManage Essentials User’s Guide at dell.
Performing initial system configuration 2 After you receive your system, you must set up your system, install the operating system if it is not preinstalled, and set up and configure the system iDRAC IP address. Setting up your system 1. Unpack the system. 2. Install the system into the rack. For more information on installing the system into the rack, see your system Rack Installation Placemat at dell.com/poweredgemanuals. 3. Connect the peripherals to the system. 4.
Logging in to iDRAC You can log in to iDRAC as an iDRAC local user, a Microsoft Active Directory user, or a Lightweight Directory Access Protocol (LDAP) user. You can also log in by using Single Sign-On or a Smart Card. The default user name is root and password is calvin. For more information on logging in to iDRAC and iDRAC licenses, see the Integrated Dell Remote Access Controller User's Guide at dell.com/esmmanuals. You can also access iDRAC using RACADM.
Steps 1. Go to dell.com/support/drivers. 2. In the Product Selection section, enter the Service Tag of your system in the Service Tag or Express Service Code field. NOTE: If you do not have the Service Tag, select Automatically detect my Service Tag for me to allow the system to automatically detect your Service Tag, or select Choose from a list of all Dell products to select your product from the Product Selection page. 3. Click Get drivers and downloads.
Pre-operating system management applications 3 The pre-operating system management applications for your system helps you manage different settings and features without booting to the operating system. Your system has the following pre-operating system management applications: • System Setup • Boot Manager • Dell Lifecycle Controller Navigation keys The navigation keys can help you quickly access the pre-operating system management applications.
About System Setup Using System Setup, you can configure the BIOS settings, iDRAC settings, and device settings of your system. You can access System Setup in two ways: • Standard Graphical Browser — This is enabled by default. • Text Browser — This is enabled by using Console Redirection. NOTE: By default, help text for the selected field is displayed in the graphical browser. To view the help text in the text browser, press .
The System BIOS screen details are explained as follows: Menu Item Description System Information Displays information about the system such as the system model name, BIOS version and Service Tag. Memory Settings Displays information and options related to the installed memory. Processor Settings Displays information and options related to the processor such as speed, cache size. SATA Settings Displays options to enable or disable the integrated SATA controller and ports.
Memory Settings screen You can use the Memory Settings screen to view all the memory settings as well as enable or disable specific memory functions such as system memory testing and node interleaving. You can view the Memory Setting screen by clicking System Setup Main Menu → System BIOS → Memory Settings. The Memory Settings screen details are explained as follows: Menu Item Description System Memory Size Displays the amount of memory installed in the system.
The Processor Settings screen details are explained as follows: Menu Item Description Logical Processor Enables or disables the logical processors and displays the number of logical processors. If the Logical Processor option is set to Enabled, the BIOS displays all the logical processors. If this option is set to Disabled, the BIOS displays only one logical processor per core. By default, the Logical Processor option is set to Enabled.
Menu Item Description X2Apic Mode Enables or disables the X2Apic mode. Number of Cores per Processor Controls the number of enabled cores in each processor. By default, the Number of Cores per Processor option is set to All. Processor 64-bit Support Specifies if the processor(s) support 64-bit extensions. Processor Core Speed Displays the maximum core frequency of the processor. Processor 1 NOTE: Depending on the number of installed CPUs, there may be up to four processor listings.
Menu Item Description Port B Sets the drive type of the selected device. For Embedded SATA settings in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS support. For AHCI mode or RAID mode, BIOS always enables support. Model Displays the drive model of the selected device. Drive Type Displays the type of drive attached to the SATA port. Capacity Displays the total capacity of the hard drive.
Boot Settings screen You can use the Boot Settings screen to set the Boot mode to either BIOS or UEFI. It also enables you to specify the boot order. To view the Boot Settings screen, click System Setup Main Menu → System BIOS → Boot Settings. Menu Item Description Boot Mode Enables you to set the boot mode of the system. CAUTION: Switching the boot mode may prevent the system from booting if the operating system is not installed in the same boot mode.
Integrated Devices screen You can use the Integrated Devices screen to view and configure the settings of all integrated devices including the video controller, integrated RAID controller, and the USB ports. You can view the Integrated Devices screen by clicking System Setup Main Menu → System BIOS → Integrated Devices. The Integrated Devices screen details are explained below. Menu Item Description USB 3.0 Setting Enables or disables the USB 3.0 support.
Menu Item Description SR-IOV Global Enable Enables or disables the BIOS configuration of Single Root I/O Virtualization (SR-IOV) devices. By default, the SR-IOV Global Enable option is set to Disabled. OS Watchdog Timer If your system stops responding, this watchdog timer aids in the recovery of your operating system. When this field is set to Enabled, the operating system is allowed to initialize the timer. When the option is set to Disabled (the default), the timer will have no effect on the system.
Menu Item Description NOTE: Every time the system boots, the BIOS syncs the serial MUX setting saved in iDRAC. The serial MUX setting can independently be changed in iDRAC. Therefore, loading the BIOS default settings from within the BIOS setup utility may not always revert this setting to the default setting of Serial Device 1. Failsafe Baud Rate Displays the failsafe baud rate for console redirection. The BIOS attempts to determine the baud rate automatically.
Menu Item Description Collaborative CPU Performance Control Enables or disables the CPU power management. When set to Enabled, the CPU power management is controlled by the OS DBPM and the System DBPM (DAPC). By default, the option is set to Disabled. Memory Patrol Scrub Sets the memory patrol scrub frequency. By default, the Memory Patrol Scrub option is set to Standard. Memory Refresh Rate Sets the memory refresh rate to either 1x or 2x. By default, the Memory Refresh Rate option is set to 1x.
Menu Item Description Password Status Locks the system password. By default, the Password Status option is set to Unlocked. TPM Security NOTE: The TPM menu is available only when the TPM module is installed. Allows you to control the reporting mode of the Trusted Platform Module (TPM). By default, the TPM Security option is set to Off.
Menu Item Description Secure Boot Policy Summary Displays the list of certificates and hashes that secure boot uses to authenticate images. Secure Boot Custom Policy Settings screen Secure Boot Custom Policy Settings is displayed only when Secure Boot Policy is set to Custom. In the System Setup Main Menu, click System BIOS → System Security → Secure Boot Custom Policy Settings. Menu Item Description Platform Key Imports, exports, deletes, or restores the platform key (PK).
Menu Item Description In-System Characterization This option enables or disables In-System Characterization. By default, In-System Characterization is set to Disabled. The two other options are Enabled and Enabled - No Reboot. NOTE: The default setting for In-System Characterization is subject to change in future BIOS releases. When enabled, In-System Characterization (ISC) executes during POST upon detecting relevant change(s) in system configuration.
Menu Item Description item in the boot order until the boot is successful or no more boot options are found. One Shot Boot Menu Takes you to the boot menu, where you can select a one time boot device to boot from. Launch System Setup Enables you to access System Setup. Launch Lifecycle Controller Exits the Boot Manager and invokes the Lifecycle Controller program. System Utilities Launches System Utilities menu such as System Diagnostics and UEFI shell.
Assigning a system and setup password Prerequisites NOTE: The password jumper enables or disables the System Password and Setup Password features. For more information about the password jumper settings, see System board connectors. You can assign a new System Password and Setup Password or change an existing System Password and Setup Password only when the password jumper setting is enabled and Password Status is Unlocked.
Steps 1. To enter System Setup, press F2 immediately after a power-on or restart. 2. In System Setup Main Menu, select System BIOS and press Enter. 3. In the System BIOS screen, select System Security and press Enter. The System BIOS screen is displayed. The System Security screen is displayed. 4. In the System Security screen, verify that Password Status is set to Unlocked. 5. Select System Password, change or delete the existing system password and press Enter or Tab. 6.
Installing and removing system components 4 Safety instructions WARNING: Whenever you need to lift the system, get others to assist you. To avoid injury, do not attempt to lift the system by yourself. WARNING: Opening or removing the system covers when the system is on may expose you to a risk of electric shock. CAUTION: Do not operate the system without the covers. This can cause damage to components. CAUTION: Many repairs may only be done by a certified service technician.
4. Turn the system on, including any attached peripherals. Recommended tools You need the following tools to perform the removal and installation procedures: • Phillips #2 screwdriver • Phillips #1 screwdriver • Torx T10 screwdriver • Torx T6 screwdriver System covers Removing the system top cover (front) Prerequisites CAUTION: Do not operate the system without the system cover. This can result in overheating and cause component damage. 1. Ensure that you read the Safety instructions. 2.
Figure 6. Removing and installing the system top cover (front) 1. system cover lock 3. system top cover (front) 2. release tab (2) Installing the system top cover (front) Prerequisites 1. Ensure that you read the Safety instructions. 2. Ensure that all internal cables are connected and routed correctly. NOTE: Closing the system cover with incorrect cable routing can damage the cables. Steps 1. Align the slots of the system top cover with the tabs on the chassis. 2.
1. Ensure that you read the Safety instructions. 2. Turn off the system, including any attached peripherals. 3. Disconnect the system from the electrical outlet and disconnect the peripherals. 4. Remove the system from the rack. 5. Keep the Phillips #1 screwdriver ready. Steps 1. Remove the screws securing the system top cover to the chassis. 2. Slide the system top cover toward the back of the system. 3. Hold the cover on both sides, and lift the cover away from the system. Figure 7.
Next steps CAUTION: Turn on the system only when both the system top covers are installed. 1. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. 2. Install the system into the rack. Inside the system Figure 8. Inside the system—PowerEdge C4130 1. GPU (4) 2. GPU switch board (optional) 3. cooling fan (8) 4. system board 5. DIMM (16) 6. processor (2) 7. power supply unit 2 slot/2.5 inch hard drive slot 8. power supply unit 1 slot 9.
11. internal USB key connector 12. expansion card riser 13. IDSDM connector 14. front inner wall of the chassis Intrusion switch Removing the intrusion switch Prerequisites NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell certified service technicians. CAUTION: Many repairs may only be done by a certified service technician.
Figure 9. Removing and installing the intrusion switch 1. intrusion switch slot 3. intrusion switch cable 2. intrusion switch Next steps Install the intrusion switch. Related Tasks Installing the intrusion switch Installing the intrusion switch Prerequisites NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell certified service technicians. CAUTION: Many repairs may only be done by a certified service technician.
Steps 1. Slide the intrusion switch into the intrusion switch slot. 2. Connect the intrusion switch cable to the connector on the system board. Next steps Follow the procedure listed in After working inside your system. Related References System board connectors Internal dual SD module (optional) Removing an internal SD card Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Steps 1. Locate the SD card slot on the internal dual SD module. NOTE: The slot is keyed to ensure correct insertion of the card. 2. Orient the SD card appropriately and insert the contact-pin end of the card into the slot. 3. Press the card into the card slot until it locks into place. Next steps Follow the procedure listed in After working inside your system. Removing the internal dual SD module Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Figure 10. Removing and installing the internal dual SD module (IDSDM) 1. IDSDM 2. pull tab 3. LED status indicator (2) 4. SD card (2) 5. SD card slot 2 6. SD card slot 1 7. IDSDM connector The following table describes the IDSDM indicator codes.
Convention IDSDM indicator code Condition E Not lit Indicates that the card is missing or is booting Next steps Follow the procedure listed in After working inside your system. Related References System board connectors Installing the internal dual SD module Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Removing the cooling shroud Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. CAUTION: Never operate your system with the cooling shroud removed.
Related Tasks Installing the cooling shroud Installing the cooling shroud Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1.
Figure 12. Removing and installing a processor blank 1. memory module socket (2) 3. processor blank 2. memory module socket ejector (2) Next steps 1. Install the processor. 2. Install the heat sink. 3. Install the memory module(s). 4. Follow the procedure listed in After working inside your system. Installing a processor blank If you are converting a dual processor system to a single processor system, install the processor blank.
1. Ensure that you read the Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Ensure that the memory module socket ejectors are in the unlocked position. Steps 1. Align the processor blank with the memory module socket on the system board. 2. Lower the processor blank into the memory module socket, and press the blank firmly until the memory module socket ejectors click into place. Next steps Follow the procedure listed in After working inside your system.
Figure 13. Memory socket locations Memory channels are organized as follows: Processor 1 channel 0: slots A1, A5 channel 1: slots A2, A6 channel 2: slots A3, A7 channel 3: slots A4, A8 Processor 2 channel 0: slots B1, B5 channel 1: slots B2, B6 channel 2: slots B3, B7 channel 3: slots B4, B8 The following table shows the memory populations and operating frequencies for the supported configurations.
DIMM Type DIMMs Populated/ Channel Operating Frequency (in MT/s) Maximum DIMM Rank/Channel 1.2 V RDIMM 1 2133, 1866, 1600, 1333 Dual rank or single rank 2 2133, 1866, 1600, 1333 Dual rank or single rank General memory module installation guidelines This system supports flexible memory configuration, enabling the system to be configured and run in any valid chipset architectural configuration.
Advanced ECC (lockstep) Advanced ECC mode extends SDDC from x4 DRAM based DIMMs to both x4 and x8 DRAMs. This protects against single DRAM chip failures during normal operation. The installation guidelines for memory modules are as follows: • Memory modules must be identical in size, speed, and technology. • DIMMs installed in memory sockets with white release levers must be identical and the same rule applies for sockets with black release levers.
Sample memory configurations The following tables show sample memory configurations for single and dual processor configurations that follow the appropriate memory guidelines. NOTE: 1R, 2R, and 4R in the following tables indicate single-, dual-, and quad-rank memory modules respectively. Table 2.
System capacity (in GB) Memory modules size (in GB) Number of memory modules Memory module rank, organization, and frequency Memory module slot population 16 4 2R, x8, 2133 MT/s, A1, A2, A3, A4 2R, x8, 1866 MT/s 32 2 2R, x8, 2133 MT/s, A1, A2 2R, x8, 1866 MT/s 96 16 6 2R, x4, 2133 MT/s, A1, A2, A3, A4, A5, A6 2R, x4, 1866 MT/s 128 16 8 2R, x4, 2133 MT/s, A1, A2, A3, A4, A5, A6, A7, A8 2R, x4, 1866 MT/s, 32 4 2R, x4, 2133 MT/s, A1, A2, A3, A4 2R, x4, 1866 MT/s, 192 32 6 2R, x4,
System capacity (in GB) Memory modules size (in GB) Number of memory modules Memory module rank, Memory module slot organization, and population frequency 2R, x8, 1866 MT/s 16 4 1R, x8, 2133 MT/s, A1, A2, B1, B2 1R, x8, 1866 MT/s 32 2 1R, x8, 2133 MT/s, A1, B1 1R, x8, 1866 MT/s 96 8 12 2R, x8, 2133 MT/s, 2R, x8, 1866 MT/s 128 8 16 2R, x8, 2133 MT/s 2R, x8, 1866 MT/s 16 8 2R, x4, 2133 MT/s, A1, A2, A3, A4, A5, A6, B1, B2, B3, B4, B5, B6 A1, A2, A3, A4, A5, A6, A7, A8, B1, B2, B3, B4, B
System capacity (in GB) Memory modules size (in GB) Number of memory modules Memory module rank, Memory module slot organization, and population frequency 512 32 16 2R, x4, 2133 MT/s A1, A2, A3, A4, A5, A6, A7, A8, B1, B2, B3, B4, B5, B6, B7, B8 Removing memory modules Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Figure 14. Removing and installing a memory module 1. memory module 3. memory module socket ejector (2) 2. memory module socket Next steps 1. Install the memory module, if applicable. 2. If you are removing a memory module permanently, install a memory module blank. NOTE: The procedure to install a memory module blank is similar to the procedure to install a memory module. 3. Install the cooling shroud.
WARNING: The memory modules are hot to touch for some time after the system has been powered down. Allow the memory modules to cool before handling them. Handle the memory modules by the card edges and avoid touching the components or metallic contacts on the memory module. CAUTION: To ensure proper system cooling, memory module blanks must be installed in any memory socket that is not occupied. Remove memory module blanks only if you intend to install memory modules in those sockets. Steps 1.
Figure 15. Installing the memory module 1. memory module 3. memory module socket ejector (2) 2. alignment key Next steps 1. Install the cooling shroud. 2. Follow the procedure listed in After working inside your system. 3. Press to enter System Setup, and check the System Memory setting. The System Memory Size should reflect the installed memory. 4. If the System Memory Size is incorrect, one or more of the memory modules may not be installed properly.
Removing a heat sink Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
Figure 16. Removing and installing a heat sink 1. captive screw (4) 2. heat sink 3. processor socket 4. screw hole (4) Next steps 1. Remove the processor. Related Tasks Removing a processor Removing a processor Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
NOTE: You can update the system BIOS by using Lifecycle Controller. 4. Follow the procedure listed in Before working inside your system. 5. Remove the cooling shroud. For more information, see Removing the cooling shroud. 6. Remove the heat sink. For more information, see Removing a heat sink WARNING: The processor will be hot to touch for some time after the system has been powered down. Allow the processor to cool before removing it. CAUTION: The processor is held in its socket under strong pressure.
Figure 17. Processor shield 1. close first socket release lever 2. lock icon 3. processor 4. open first socket release lever 5.
Figure 18. Removing and installing a processor 1. close first socket release lever 2. pin-1 indicator of processor 3. processor 4. slot (4) 5. processor shield 6. open first socket release lever 7. socket 8. socket keys (4) Next steps 1. Install the processor. 2. Install the heat sink. 3. Follow the procedure listed in After working inside your system.
Installing a processor Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Ensure that you read the Safety instructions. 2.
12. Lower the open first socket release lever near the unlock icon it. and push it under the tab to lock Next steps NOTE: Ensure that you install the heat sink after you install the processor. The heat sink is necessary to maintain proper thermal conditions. 1. Install the heat sink. 2. Follow the procedure listed in After working inside your system. Related Tasks Installing a heat sink Installing a heat sink Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Figure 19. Applying thermal grease on the top of the processor 1. processor 3. thermal grease syringe 2. thermal grease 3. Place the heat sink onto the processor. 4. Tighten one of the four screws to secure the heat sink to the system board. 5. Tighten the screw diagonally opposite to the first screw you tightened. NOTE: Do not over-tighten the heat sink retention screws when installing the heat sink.
System battery Replacing the system battery Prerequisites NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell certified service technicians. WARNING: There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. For more information, see the safety information that shipped with your system.
Figure 20. Removing the system battery 1. negative side of the battery connector 3. positive side of the battery connector 2. system battery 3. To install a new system battery, hold the battery with the "+" sign facing up and slide it under the securing tabs at the positive side of the connector. 4. Press the battery into the connector until it locks into place. Figure 21. Installing the system battery 1. system battery 2.
Next steps 1. Connect the GPU signal and power cables to the system board. 2. Follow the procedure listed in After working inside your system. 3. While booting, press to enter System Setup and ensure that the battery is operating properly. 4. Enter the correct time and date in the System Setup Time and Date fields. 5. Exit System Setup.
Figure 22. Removing and installing the PCIe shroud 1. slot on the heat sink (2) 2. tab on the PCIe shroud (2) 3. PCIe shroud 4. expansion card riser Next steps 1. Install the PCIe shroud. Related Tasks Installing the PCIe shroud Installing the PCIe shroud Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Steps Insert the tabs on the PCIe shroud into the slots on the heat sink. Next steps Follow the procedure listed in After working inside your system. Expansion card riser and expansion cards Expansion card installation guidelines Depending on your system configuration, the following PCI Express generation 3 expansion cards are supported: Table 4.
Configuration PCIe slot Processor connection Height Length Link width Slot width Four GPUs with switch 1 board with dual GPU virtual mode and two processors 2 (Configuration G) Processor 1 Low Profile Half Length x16 x16 Processor 2 Low Profile Half Length x16 x16 Three GPUs without switch board and two processors 1 Processor 1 Low Profile Half Length x8 x16 (Configuration H) 2 Processor 2 Low Profile Half Length x8 x16 Three GPUs without switch board and two processors 1 P
Card priority Card type Configurations A, B, C, D, F, G, and H Configurations E and I Slot priority Max allowed Slot priority Max allowed 10 EMULEX dual port 16 Gbps Fibre Channel adapter 1, 2 2 1 1 11 QLOGIC single port 16 Gbps Fibre Channel adapter 1, 2 2 1 1 12 EMULEX single port 16 Gbps Fibre Channel adapter 1, 2 2 1 1 13 10 Gb NICs (low profile) 1, 2 2 1 1 14 10 Gb SFP+ NICs (low profile) 1, 2 2 1 1 Removing the expansion card riser Prerequisites CAUTION: Many repa
Figure 23. Removing and installing the expansion card riser 1. touch point (4) 2. expansion card riser 3. expansion card clip 4. guide slot on the chassis 5. expansion card latch 6. riser connector on the system board 7. guide pin on the system board 8. guide post on the expansion card riser Next steps 1. Install the expansion card, if applicable. 2. Install the expansion card riser.
2. Follow the procedure listed in Before working inside your system. 3. If applicable, install the expansion card(s) into the expansion card riser. For more information, see Installing expansion cards. Steps 1. Align the expansion card riser with the guide pin on the system board and the guide slot on the chassis. 2. Lower the expansion card riser and press it until it clicks into place.
b. Close the expansion card clip. NOTE: You must install an expansion card blank to maintain Federal Communications Commission (FCC) certification of the system. The expansion card blank keeps dust and dirt out of the system and aids in proper cooling and airflow inside the system. Figure 24. Removing and installing the expansion card from the expansion card riser 1. touch point (4) 2. expansion card riser 3. expansion card clip 4. expansion card (low-profile, half-length card) 5.
3. Remove the PCIe shroud. For more information, see Removing the PCIe shroud. 4. Remove the expansion card riser cables. CAUTION: The expansion card riser cables should be removed before removing the expansion card riser to prevent pin damage in the PCIe connectors on the system/switch board. 5. Remove the expansion card riser. For more information, see Removing the expansion card riser. Steps 1. Locate the expansion card connector on the expansion card riser. 2. Open the expansion card clip. 3.
3. Install the PCIe shroud. 4. Follow the procedure listed in After working inside your system. Related Tasks Installing the expansion card riser Installing the PCIe shroud Expansion card cabling diagrams Cabling two expansion cards Figure 26. Cabling two expansion cards 1. GPU 4 PCIe connector on the system board 2.
3. expansion slot 2 connector (x16) 4. expansion slot 1 connector (x16) 5. expansion card riser 6. system board Cabling one expansion card Figure 27. Cabling one expansion card 1. GPU 1 PCIe connector on the system board 2. expansion slot 2 connector (x16) 3. expansion card riser 4.
Power supply units Your system supports up to: • Two 1600 W AC power supply units (PSUs) or • Two 1100 W AC PSUs (only for systems that support two GPUs) NOTE: The PSU 2 slot also functions as the optional 2.5 inch hard drive cage slot. If you install the 2.5 inch hard drive cage in the PSU 2 slot, your system will not support the redundancy feature. NOTE: Platinum 1600 W PSU is rated for 200 V AC to 240 V AC input only.
Removing the power supply unit blank Remove the power supply unit (PSU) blank when you are installing a second PSU or a 2.5 inch hard drive cage in the PSU 2 slot. Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Installing the power supply unit blank Install the power supply unit (PSU) blank when you remove PSU 2 or the 2.5 inch hard drive cage from the PSU 2 slot. Install the PSU blank only in the PSU 2 slot. Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Figure 29. Removing and installing an AC PSU 1. release latch 2. PSU power cable connector 3. PSU 4. PSU connector 5. PSU handle Next steps Depending on your requirement, perform one of the following steps: • If you are not replacing PSU 2 immediately, install a PSU blank. • Install the replacement AC PSU. • Install the 2.5 inch hard drive cage. Related Tasks Installing an AC power supply unit Installing the power supply unit blank Installing the optional 2.
NOTE: The maximum output power (shown in watts) is listed on the PSU label. 3. If applicable, remove the PSU blank. For more information, see Removing the power supply unit blank. Steps 1. Slide the replacement PSU into the PSU slot until the PSU is fully seated and the release latch snaps into place. CAUTION: When connecting the power cable, secure the cable with the strap. 2. Connect the PSU power cable to the PSU power cable connector.
NOTE: When you slide the hard drive cage out of the hard drive cage slot, ensure that the cables disconnected from the system board do not interfere with other components on the system board. 2. Slide the hard drive cage out of the hard drive cage slot. Figure 30. Removing and installing the 2.5 inch hard drive cage 1. PSU 1 slot 2. PSU 2 slot/2.5 inch hard drive cage slot 3. screw 4.
1. Ensure that you read the Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the PSU/PSU blank, if installed. See Removing the power supply unit blank, Removing an AC power supply unit. 4. Install the 2.5 inch hard drives in the hard drive cage. See Installing a 2.5 inch cabled hard drive into the hard drive cage. 5. Route the power and signal cables through the hard drive cage slot. 6. Keep the Phillips #1 screwdriver ready. Steps 1.
Figure 31. Removing and installing the 2.5 inch hard drive cage cover 1. slot on the hard drive cage (2) 2. hard drive cage 3. hard drive cage cover 4. screw (2) Next steps Depending on your requirement, install or remove the 2.5 inch hard drive(s). Related Tasks Installing a 2.5 inch cabled hard drive into the hard drive cage Removing 2.5 inch cabled hard drives from the hard drive cage Installing the optional 2.
3. Use the screws to secure the hard drive cage cover to the hard drive cage. Next steps 1. Install the hard drive cage into the PSU 2 slot/2.5 inch hard drive slot on the chassis. 2. Follow the procedure listed in After working inside your system. Removing 2.5 inch cabled hard drives from the hard drive cage Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Figure 32. Removing and installing a 2.5 inch cabled hard drive (hard drive 0/E and hard drive 1/F) from the hard drive cage 3. hard drive 1/F 2. power and signal cable connector (2) 3. power and signal cable connector on hard drive 4. hard drive 0/E 5. screw (8) 6. hard drive cage If you want to remove hard drives 2/C and 3/D, perform the following steps: a. b. c. d. e. 94 1. Remove hard drives 0/E and 1/F. Disconnect the signal/power cables from hard drive 2/C and 3/D.
Figure 33. Removing and installing a 2.5 inch cabled hard drive (hard drive 2/C and hard drive 3/D) from the hard drive cage 1. screw (8) 2. hard drive cage 3. cable routing clip 4. power cable 5. signal cable 6. hard drive 2/C 7. hard drive 3/D Next steps 1. Install the hard drives. 2. Install the hard drive cage cover. 3. Install the hard drive cage into the hard drive cage slot in the chassis. Related Tasks Installing a 2.
2. Keep the Phillips #2 screwdriver ready. 3. Remove the hard drive cage. For more information, see Removing the optional 2.5 inch hard drive cage. 4. Remove the hard drive cage cover. For more information, see Removing the optional 2.5 inch hard drive cage cover. NOTE: If you are installing four hard drives, ensure that you install hard drives 3/D and 2/C before you install hard drives 1/F and 0/E. NOTE: If you are installing two hard drives, install hard drives 1/F and 0/E.
Hard drive cabling diagrams Cabling SAS and SATA hard drives to the RAID card Figure 34. Cabling SAS and SATA hard drives to the RAID card 1. system board 2. 2.5 inch hard drive cage power connector 3. power cable 4. 2.5 inch hard drive cage slot 5. Port A connector on the RAID card 6.
Cabling SATA hard drives to the SATA connector on the system board Figure 35. Cabling SATA hard drives to the SATA connector on the system board 1. system board 2. 2.5 inch hard drive cage power connector 3. power cable 4. 2.5 inch hard drive cage slot 5. SATA connector on the system board 6.
uSATA SSDs The PowerEdge C4130 supports up to two 1.8 inch uSATA Solid State Drives (SSDs). The uSATA SSDs connect to the system board through the hard drive backplane. NOTE: Use only SSDs that have been tested and approved for use with the hard drive backplane. When you format an SSD, allow enough time for the formatting to be completed. High-capacity SSDs can take a number of hours to format. Removing a 1.8 inch uSATA SSD blank Prerequisites 1. Ensure that you read the Safety instructions.
Installing a 1.8 inch uSATA SSD blank Install the SSD blank if you are removing the SSD permanently or not replacing it immediately. Prerequisites Ensure that you read the Safety instructions. Steps Insert the SSD blank into the SSD slot until the release button clicks into place. Removing a 1.8 inch uSATA SSD carrier You need to remove the SSD carrier because the SSD is installed in the SSD carrier. Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Figure 37. Removing and installing a 1.8 inch uSATA SSD carrier 1. release button 3. SSD carrier handle 2. SSD carrier Next steps Depending on your requirement, perform one of the following steps: • If you are not replacing the SSD immediately, insert an SSD blank in the empty SSD slot. • Install the 1.8 inch uSATA SSD carrier. Related Tasks Installing a 1.8 inch uSATA SSD blank Installing a 1.8 inch uSATA SSD carrier Installing a 1.
Steps 1. If an SSD blank is installed in the SSD slot, remove it. For more information, see Removing a 1.8 inch uSATA SSD blank. 2. Install the SSD in the SSD carrier. For more information, see Installing a 1.8 inch uSATA SSD into a SSD carrier. 3. Press the release button on the front of the SSD carrier, and open the SSD carrier handle. 4. Insert the SSD carrier into the SSD slot until the carrier connects with the backplane. 5. Close the SSD carrier handle to lock the SSD in place. Next steps 1.
Figure 38. Removing and installing a 1.8 inch SSD into a SSD carrier 1. SSD carrier 2. SSD Next steps Install the SSD into the SSD carrier. Related Tasks Installing a 1.8 inch uSATA SSD into a SSD carrier Installing a 1.8 inch uSATA SSD into a SSD carrier Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Removing the 1.8 inch uSATA SSD cage Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Ensure that you read the Safety instructions. 2.
5. tab on the PSU 1 slot 6. slot on the chassis Installing the 1.8 inch uSATA SSD cage Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1.
Steps 1. Remove the screw securing the SSD backplane to the SSD cage. 2. Remove the SSD backplane from the slot on the SSD cage. Figure 40. Removing and installing the 1.8 inch SSD backplane 1. screw 2. SSD backplane 3. tab on the SSD backplane 4. slot on the SSD backplane 5. SSD cage Installing the 1.8 inch uSATA SSD backplane Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
2. Follow the procedure listed in After working inside your system. Related Tasks Installing the 1.8 inch uSATA SSD cage Internal USB memory key (optional) The USB memory key installed inside your system can be used as a boot device, security key, or mass storage device. To boot from the USB memory key, configure the USB memory key with a boot image and then specify the USB memory key in the boot sequence in System Setup. The internal USB connector is located on the system board.
Figure 41. Replacing the internal USB key 1. USB memory key 2. USB memory key connector Next steps 1. Install the 1.8 inch uSATA SSD cage. 2. Follow the procedure listed in After working inside your system. 3. While booting, press to enter System Setup and verify that the USB key is detected by the system. Related Tasks Installing the 1.
Steps 1. Remove the screws securing the cable routing clip to the system board. 2. Lift the cable routing clip away from the system board. Figure 42. Removing and installing the cable routing clip 1. cable routing clip 3. screw hole on the system board (2) 2. screw (2) Installing the cable routing clip Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
System board Removing the system board Prerequisites NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell certified service technicians. CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Steps 1. Remove the screws that secure the system board to the chassis. CAUTION: Take care not to damage the system identification button while removing the system board from the chassis. CAUTION: Do not lift the system board by holding a memory module, processor, or other components. 2. Lift the system board by holding both the system board holders, and slide the system board toward the front of the chassis. The connectors are disengaged from the back of the chassis slots. 3.
Figure 44. Removing and installing the system board 1. system board 3. system board holder (back) 2. system board holder (front) Next steps Install the system board. Related Tasks Installing the system board Installing the system board Prerequisites NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell certified service technicians.
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Ensure that you read the Safety instructions. 2.
a. Use the Easy Restore feature to restore the service tag. For more information, see Restoring the Service Tag using the Easy Restore feature. b. If the service tag is not backed up in the backup flash device, enter the system service tag manually. For more information, see Entering the system service tag. c. Update the BIOS and iDRAC versions. d. Re-enable the Trusted Platform Module (TPM). For more information, see Re-enabling the TPM for TXT users.
Trusted Platform Module The Trusted Platform Module (TPM) is used to generate or store keys, protect or authenticate passwords, and create or store digital certificates. TPM can also be used to enable the BitLocker hard drive encryption feature in Windows Server. CAUTION: Do not attempt to remove the Trusted Platform Module (TPM) from the system board. Once the TPM is installed, it is cryptographically bound to that specific system board.
Figure 45. Installing the TPM 1. TPM 2. TPM connector 3. slot on the TPM connector 4. plastic bolt 5. slot on the system board Re-enabling the TPM for BitLocker users Initialize the TPM. For more information on initializing the TPM, see http://technet.microsoft.com/en-us/library/ cc753140.aspx. The TPM Status changes to Enabled, Activated. Re-enabling the TPM for TXT users 1. While booting your system, press to enter System Setup. 2.
Cooling fans Your system supports six cabled cooling fans. Removing a cooling fan Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1.
Figure 46. Removing and installing a cooling fan 1. cooling fan (8) 2. cooling fan power cable 3. cooling fan connector on system board 4. cooling fan slot Next steps 1. Install the cooling fan. Installing a cooling fan Prerequisites 1. Ensure that you read the Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the system top cover (front). For more information, see Removing the system top cover (front).
3. Connect the cooling fan power cable to the cooling fan connector on the system board. Next steps 1. Install the system top cover (front). 2. Follow the procedure listed in After working inside your system. Graphics processing unit NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell certified service technicians. The following are the high-level steps that you must perform to replace the GPU: 1. Remove the GPU blank. 2.
Removing a GPU blank You can remove the GPU blank only in configuration D. To remove GPU 2 in configuration D, remove the GPU blank from GPU slot 1. Do not remove GPU blanks in any other configuration. Prerequisites NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should only be done by Dell certified service technicians. CAUTION: Many repairs may only be done by a certified service technician.
Figure 47. Removing and installing a GPU blank 1. guide pin on the front inner wall of the chassis (2) 2. slot on the GPU blank (2) 3. GPU blank 4. guide holes on the back of the GPU blank (2) 5. guide pin on the chassis (2) Removing a GPU riser cable from the system board Prerequisites NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should only be done by Dell certified service technicians.
Steps 1. Press the release latches located on the GPU riser cable connector on the system board. NOTE: Pressing the release latches will not eject the GPU riser cable from the system board. 2. Pull the GPU riser cable out of the GPU riser cable connector on the system board. Figure 48. Removing and installing a GPU riser cable from the system board 1. riser cable connector 3. release latch (2) 2. riser cable connector on the system board Next steps Remove the GPU.
2. Remove the GPU riser cables connected to the switch board or system board. CAUTION: The GPU riser cables should be removed before removing the GPUs to prevent pin damage in the GPU connectors on the system board. 3. Disconnect the power cables connected to the system board. Steps 1. Hold the GPU by the support brackets, and lift the GPU at an angle to release it from the guide pins on the front inner wall of the chassis. NOTE: Do not hold the GPU by the GPU riser cable board while removing the GPU.
Next steps Remove the GPU riser cable board. Related Tasks Removing a GPU riser cable board Removing a GPU riser cable board Prerequisites NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell certified service technicians. CAUTION: Many repairs may only be done by a certified service technician.
Figure 50. Removing and installing a GPU riser cable board 1. connector on the GPU riser cable board 2. GPU riser cable board 3. GPU riser cable 4. screw (3) 5. GPU riser cable clip 6. GPU Next steps Removing the custom GPU brackets from the GPUs removed from your system.
3. Remove the GPU riser cable board. For more information, see Removing a GPU riser cable board. NOTE: Depending on the type of Nvidia GPUs supported on your system, the location of the screws and type of GPU brackets will vary. Steps 1. Remove the screws securing the front I/O bracket to the GPU, and remove the I/O bracket. 2. Remove the screws securing the support bracket to the GPU, and remove the support bracket. Figure 51.
Figure 52. Removing and installing the custom Intel GPU I/O brackets and the support brackets 1. support bracket 2. GPU 3. screw (8) 4. I/O bracket Next steps Remove the GPU brackets from the replacement GPUs. Related Tasks Removing the GPU brackets from the replacement GPUs Removing the GPU brackets from the replacement GPUs The Nvidia or Intel replacement GPUs are shipped with specific Nvidia or Intel I/O and support brackets.
Steps 1. Remove the screws securing the front I/O bracket to the GPU, and remove the I/O bracket. 2. Remove the screws securing the support bracket to the GPU, and remove the support bracket. Figure 53. Removing and installing the GPU I/O brackets and the support brackets (Nvidia) 128 1. Torx screw 2. support bracket 3. GPU 4. I/O bracket 5.
Figure 54. Removing and installing the GPU I/O brackets and the support brackets (Intel) 1. support bracket 2. GPU 3. screw (8) 4. I/O bracket Next steps Install the brackets on the GPU that you removed from your system. Related Tasks Installing the GPU brackets on the GPU removed from your system Installing the GPU brackets on the GPU removed from your system The Nvidia or Intel replacement GPU(s) are shipped with specific Nvidia or Intel I/O and support brackets.
Steps 1. Align the screw holes on the front I/O bracket with the screw holes on the GPU. 2. Secure the I/O bracket to the GPU by using the screws. 3. Align the screw holes on the support bracket with the screw holes on the GPU. 4. Secure the support bracket to the GPU by using the screws. Next steps Install the custom GPU brackets on the replacement GPU.
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Ensure that you read the Safety instructions. 2. Keep the Philips #2 screwdriver ready. 3.
Next steps Install GPU 2. Related Tasks Installing a GPU Installing a GPU Your system supports up to four GPUs. Prerequisites NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell certified service technicians. CAUTION: Many repairs may only be done by a certified service technician.
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Ensure that you read the Safety instructions. 2. Install the GPU.
GPU cabling diagrams Cabling configuration A and B systems Figure 55. Cabling single and dual processor systems with four GPUs and a GPU switch board (Configurations A and B) 1. GPU 4 riser cable connector on the GPU 2. GPU switch board 3. GPU 3 connector on the GPU switch board 4. GPU 4 connector on the GPU switch board 5. system board 6. GPU 2 connector on the system board 7. GPU 2 connector on the GPU switch board 8. GPU 1 connector on the GPU switch board 9.
11. GPU 1 12. GPU 2 riser cable connector on the GPU 13. GPU 2 14. GPU 3 15. GPU 3 riser cable connector on the GPU 16. GPU 4 Figure 56. Power cabling for single and dual processor systems with four GPUs and a GPU switch board (Configurations A and B) 1. GPU 4 power connector on the system board 2. GPU 3 power connector on the system board 3. GPU 1/2 power connector on the system board 4. GPU switch board power connector on the system board 5. system board 6.
9. GPU 1 10. GPU 2 11. power connector on GPU 2 12. power connector on GPU 3 13. GPU 3 14. GPU 4 15. power connector on GPU 4 Cabling configuration C systems Figure 57. Cabling a dual processor system with four GPUs (Configuration C) 1. GPU 4 riser cable connector on the GPU 2. GPU 3 connector on the system board 3. GPU 4 connector on the system board 4. GPU 1 connector on the system board 5. system board 6. GPU 2 connector on the system board 7.
9. GPU 2 riser cable connector on the GPU 10. GPU 2 11. GPU 3 12. GPU 3 riser cable connector on the GPU 13. GPU 4 Figure 58. Power cabling for a dual processor system with four GPUs (Configuration C) 1. GPU 4 power connector on the system board 2. GPU 3 power connector on the system board 3. GPU 1/2 power connector on the system board 4. system board 5. power connector on GPU 1 6. GPU 1 7. GPU 2 8. power connector on GPU 2 9. power connector on GPU 3 10. GPU 3 11. GPU 4 12.
Cabling configuration D systems Figure 59. Cabling a dual processor system with two GPUs (Configuration D) 1. GPU 3 riser cable connector on the system board 2. system board 3. GPU 2 connector on the system board 4. GPU 1 blank 5. GPU 2 riser cable connector on the GPU 6. GPU 2 7. GPU 3 8. GPU 3 riser cable connector on the GPU 9.
Figure 60. Power cabling for a dual processor system with two GPUs (Configuration D) 1. GPU 1/2 power connector on the system board 2. system board 3. GPU 1 blank 4. GPU 2 5. power connector on GPU 2 6. power connector on GPU 3 7. GPU 3 8.
Cabling configuration E systems Figure 61. Cabling a single processor system with two GPUs (Configuration E) 1. GPU 1 connector on the system board 2. system board 3. GPU 2 connector on the system board 4. GPU 1 connector on the GPU 5. GPU 1 6. GPU 2 connector on the GPU 7. GPU 2 8.
Figure 62. Power cabling for a single processor system with two GPUs (Configuration E) 1. GPU 1/2 power connector on the system board 2. system board 3. power connector on GPU 1 4. GPU 1 5. GPU 2 6. power connector on GPU 2 7.
Cabling Configuration F systems Figure 63. Cabling a dual processor system with two GPUs (Configuration F) 1. GPU 1 connector on the system board 2. system board 3. GPU 2 connector on the system board 4. GPU 1 connector on the GPU 5. GPU 1 6. GPU 2 connector on the GPU 7. GPU 2 8.
Figure 64. Power cabling for a dual processor system with two GPUs (Configuration F) 1. GPU 1/2 power connector on the system board 2. system board 3. power connector on GPU 1 4. GPU 1 5. GPU 2 6. power connector on GPU 2 7.
Cabling configuration G systems Figure 65. Cabling a dual processor system with four GPUs and a GPU switch board with dual GPU virtual mode (Configuration G) 1. GPU 4 riser cable connector on the GPU 2. GPU switch board 3. CPU 2 connector on the GPU switch board 4. GPU 4 connector on the GPU switch board 5. GPU 3 connector on the GPU switch board 6. GPU switch board connection to CPU 2 on the system board 7. system board 8. GPU switch board connection to CPU 1 on the system board 9.
13. GPU 1 14. GPU 2 riser cable connector on the GPU 15. GPU 2 16. GPU 3 17. GPU 3 riser cable connector on the GPU 18. GPU 4 Figure 66. Power cabling for a dual processor system with four GPUs and a GPU switch board with dual GPU virtual mode (Configuration G) 1. GPU 4 power connector on the system board 2. GPU 3 power connector on the system board 3. GPU 1/2 power connector on the system board 4. GPU switch board power connector on the system board 5. system board 6.
9. GPU 1 10. GPU 2 11. power connector on GPU 2 12. power connector on GPU 3 13. GPU 3 14. GPU 4 15. power connector on GPU 4 Cabling configurations H and I Figure 67. Cabling a dual processor system with three GPUs (Configurations H and I) 1. GPU 3 connector on the system board 2. GPU 1 connector on the system board 3. system board 4. GPU 2 connector on the system board 5. GPU 1 riser cable connector on GPU 1 6. GPU 1 7. GPU 2 riser cable connector on GPU 2 8.
9. GPU 3 11. GPU 4 blank 10. GPU 3 riser cable connector on GPU 3 Figure 68. Power cabling for a dual processor system with three GPUs (Configurations H and I) 1. GPU 3 power connector on the system board 2. GPU 1/2 power connector on the system board 3. system board 4. power connector on GPU 1 5. GPU 1 6. GPU 2 7. power connector on GPU 2 8. power connector on GPU 3 9. GPU 3 10.
GPU switch board (optional) Removing the optional GPU switch board Prerequisites NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell certified service technicians. CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Figure 69. Removing and installing the GPU switch board 1. GPU switch board 3. tab on the chassis (2) 2. captive screw (2) Next steps 1. Install the system top cover (front). 2. Follow the procedure listed in After working inside your system. Related Tasks Installing the system top cover (front) Installing the optional GPU switch board Prerequisites NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell certified service technicians.
3. Keep the Philips #2 screwdriver ready. 4. Remove the GPUs. For more information, see Removing a GPU. Steps 1. Align the tabs on the chassis with the slots on the GPU switch board. 2. Slide the GPU switch board toward the back of the chassis to engage the slots on the GPU switch board with the tabs on the chassis. 3. Tighten the screws securing the switch board to the chassis. Next steps 1. Connect the GPU switch board power cable. 2. Install the GPUs. 3.
Figure 70. Removing and installing the control panel module 1. screw (2) 2. plastic pull tab 3. control panel cable 4. control panel connector 5. control panel board 6. notch 7. control panel module Next steps 1. Install the control panel module. 2. Follow the procedure listed in After working inside your system. Related Tasks Installing the control panel module Installing the control panel module Prerequisites NOTE: This is a Field Replaceable Unit (FRU).
Steps 1. Insert the control panel module behind the notch on the chassis. 2. Align the screw holes on the control panel module with the screw holes on the chassis. 3. Secure the control panel module to the chassis by using the screws. 4. Connect the control panel cable to the control panel connector. Next steps Follow the procedure listed in After working inside your system.
Troubleshooting your system 5 Safety first—for you and your system CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
Troubleshooting a USB device About this task Follow steps 1 to 6 to troubleshoot a USB keyboard or mouse. For other USB devices, go to step 7. Steps 1. Disconnect the keyboard and/or mouse cables from the system and reconnect them. 2. If the problem persists, connect the keyboard and/or mouse to another USB port on the system. 3. If the problem is resolved, restart the system, enter System Setup, and check if the non-functioning USB ports are enabled. NOTE: Older operating systems may not support USB 3.
Next steps If the problem persists, see Getting Help. Troubleshooting a NIC Steps 1. Run the appropriate diagnostic test. For more information, see Using system diagnostics for available diagnostic tests. 2. Restart the system and check for any system messages pertaining to the NIC controller. 3. Check the appropriate indicator on the NIC connector: • If the link indicator does not light, check all cable connections.
• USB memory key • PCIe shroud • 2.5 inch hard drive cage • Cooling shroud • Expansion card risers (if present) • Expansion cards • Power supply unit(s) • Cooling fans • Processor(s) and heat sink(s) • Memory modules 2. • Power/data cables Let the system dry thoroughly for at least 24 hours. 3. Reinstall the components (except expansion cards) you removed in step 3. 4. Install the system cover. 5. Turn on the system and attached peripherals.
• Hard drives • Hard drive backplane • 1.8 inch hard drive cage • GPUs • GPU blanks • GPU switch board • Power and data cables 4. • Riser cables Ensure that all cables are properly connected. 5. Install the system covers (front and back). 6. Run the appropriate diagnostic test. For more information, see Using system diagnostics. Next steps If the tests fail, see Getting Help.
Troubleshooting power supply units CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. Troubleshooting power source problems 1.
Troubleshooting cooling problems CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
1. Ensure that you read the Safety instructions. 2. Follow the procedure listed in Before working inside your system. Steps 1. Remove the system covers (front and back). CAUTION: Do not operate the system without the system cover. This can result in overheating and cause component damage. 2. Reseat the fan or the fan's power cable. 3. Install the system covers (front and back). 4. Restart your system. Next steps If the problem persists, see Getting Help.
13. To troubleshoot an unspecified faulty memory module, replace the memory module in the first DIMM socket with a module of the same type and capacity. If an error message is displayed on the screen, this may indicate a problem with the installed DIMM type(s), incorrect DIMM installation, or defective DIMM(s). Follow the on-screen instructions to resolve the problem. 14. Install the system cover. 15.
NOTE: Certain SD cards have a physical write-protect switch on the card. If the write-protect switch is turned on, the SD card is not writable. Steps 1. Enter System Setup, and ensure that the Internal SD Card Port is enabled. 2. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 3. Remove the system cover. NOTE: When an SD card failure occurs, the internal dual SD module controller notifies the system.
d. Exit the configuration utility and allow the system to boot to the operating system. 3. Ensure that the required device drivers for your controller card are installed and are configured correctly. See the operating system documentation for more information. 4. Reboot the system and enter System Setup. 5. Verify that the controller is enabled and the drives are displayed in System Setup. Next steps If the problem persists, try troubleshooting the expansion cards or see Getting Help.
Troubleshooting expansion cards Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
Steps 1. Run the appropriate diagnostics test. See Using system diagnostics for available diagnostic tests. 2. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet. 3. Remove the system cover. 4. Ensure that the processor and heat sink are properly installed. 5. Install the system cover. 6. Run the appropriate diagnostic test. For more information, see Using system diagnostics. Next steps If the problem persists, see Getting Help.
Alert messages The systems management software generates alert messages for your system. Alert messages include information, status, warning, and failure messages for drive, temperature, fan, and power conditions. For more information, see the systems management software documentation.
Using system diagnostics 6 If you experience a problem with your system, run the system diagnostics before contacting Dell for technical assistance. The purpose of running system diagnostics is to test your system hardware without requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service and support personnel can use the diagnostics results to help you solve the problem.
Running the Embedded System Diagnostics from the Dell Lifecycle Controller 1. As the system boots, press . 2. Select Hardware Diagnostics → Run Hardware Diagnostics. The ePSA Pre-boot System Assessment window is displayed, listing all devices detected in the system. The diagnostics starts executing the tests on all the detected devices. System diagnostic controls Menu Description Configuration Displays the configuration and status information of all detected devices.
Jumpers and connectors 7 System board jumper settings For information on resetting the password jumper to disable a password, see Disabling a forgotten password. Table 6. System board jumper settings Jumper PWRD_EN Setting Description The password reset feature is enabled (pins 2–4). BIOS local access is unlocked at the next AC power cycle. The password reset feature is disabled (pins 4–6). NVRAM_CLR The configuration settings are retained at the next system boot (pins 3–5).
System board connectors Figure 71. System board jumpers and connectors Item Connector Description 1 CTRL_PNL Front panel connector 2 GPU3 (CPU2_PE3_ABCD) GPU 3 PCIe Connector 3 4HDD_PWR 2.5 inch hard drive cage power connector 4 GPU_4_PWR GPU 4 power connector 5 GPU_3_PWR GPU 3 power connector 6 GPU_1/2_PWR GPU 1/2 power connector 7 PLX_PWR (PCIe_Switch_board) Switch board power connector 8 2SSD_BP 1.
Item Connector Description 12 USB_INT Internal USB connector 13 4HHD_SIG SATA x4 signal connector 14 PSWD & PSWD_NVRAM Password jumpers 15 GPU4 (CPU2_PE2_ABCD) GPU 4 PCIe connector 16 GPU1 (CPU1_PE3_ABCD) GPU 1 PCIe connector 17 A3, A7, A4, A8 Memory module sockets for processor 1 18 A1, A5, A2, A6 Memory module sockets for processor 1 19 GPU2 (CPU1_PE2_ABCD) GPU 2 PCIe connector 20 IDSDM Internal dual SD module connector 21 FAN-1 Fan 1 connector 22 FAN-2 Fan 2 connector
Steps 1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 2. Remove the system cover. 3. Move the jumper on the system board jumper from pins 4 and 6 to pins 2 and 4. 4. Install the system cover. The existing passwords are not disabled (erased) until the system boots with the jumper on pins 2 and 4. However, before you assign a new system and/or setup password, you must move the jumper back to pins 4 and 6.
Technical specifications 8 Processor Processor type One or two Intel Xeon processor E5-2600 v3 product family Power AC power supply (per power supply unit (PSU) Wattage 1100 W and 1600 W NOTE: 1100 W PSUs are supported only on systems with two GPUs. Heat dissipation NOTE: Heat dissipation is calculated using the PSU wattage rating. Voltage NOTE: This system is also designed to be connected to IT power systems with a phase-to-phase voltage not exceeding 230 V.
Memory Architecture 1333 MT/s, 1600 MT/s, 1866 MT/s or 2133 MT/s DDR4 registered, Error Correcting Code (ECC) DIMMs Support for advanced ECC or memory optimized operation Memory module sockets Sixteen 288-pin Memory module capacities RDIMMs Minimum RAM 4 GB single-ranked, 8 GB, 16 GB, 32 GB dualranked 4 GB with a single processor 8 GB with a dual processor (minimum one memory module per processor) Maximum RAM Up to 512 GB with a dual processor Up to 256 GB with a single processor Drives Hard drives
Physical Height 4.31 cm (1.7 inch) Width 43.4 cm (17.09 inch) Length 88.58 cm (34.87 inch) Maximum configuration weight 20.2 kg (44.53 lb) Empty weight 12 kg (26.45 lb) Environmental specifications NOTE: For additional information about environmental measurements for specific system configurations, see dell.com/environmental_datasheets.
Environmental specifications on each side of the system) of 71 G for up to 2 ms. Maximum altitude Operating 3048 m (10,000 ft). Storage 12,000 m (39,370 ft). Operating temperature de-rating Up to 25°C (77 °F) Maximum temperature is reduced by 1°C/300 m (1°F/547 ft) above 950 m (3,117 ft). Particulate contamination NOTE: This section defines the limits to help avoid IT equipment damage and/or failure from particulates and gaseous contamination.
Getting help 9 Contacting Dell Dell provides several online and telephone-based support and service options. If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer-service issues: 1. Go to dell.com/support. 2.
Mini Express Service Tag The Mini Express Service Tag (MEST) label which has the Service tag number of your system. It is located on top of the left rack latch. To access the MEST, the chassis will need to be pulled out of the rack about two inches. Quick Resource Locator Use the Quick Resource Locator (QRL) to get immediate access to system information and how-to videos. This can be done by visiting dell.
