User’s Guide Dell S2218H/S2318H/S2318HX Model No.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury or death. _________________________ Information in this document is subject to change without notice. © 2017 Dell Inc. All rights reserved.
Contents About Your Monitor................................................................. 5 Package Contents....................................................................................... 5 Product Features.........................................................................................6 Identifying Parts and Controls..................................................................8 Plug and Play Capability...........................................................................
Setting the Maximum Resolution........................................................... 31 Using the Tilt..............................................................................................32 Troubleshooting..................................................................... 33 Self-Test......................................................................................................33 Built-in diagnostics...................................................................................
About Your Monitor Package Contents Your monitor ships with the components shown below. Ensure that you have received all the components and Contact Dell if something is missing. NOTE: Some items may be optional and may not ship with your monitor. Some features or media may not be available in certain countries. NOTE: To set up with any other stand, please refer to the respective stand setup guide for setup instructions.
∞∞ HDMI Cable ∞∞ VGA Cable (for S2318HX only) ∞∞ Cable Holder ∞∞ Quick Setup Guide ∞∞ Safety and Regulatory Information Product Features The Dell S2218H_S2318H_S2318HX flat panel display has an active matrix, ThinFilm Transistor (TFT), Liquid Crystal Display (LCD), In-plane Switching panel and LED backlight. The monitor features include: ∞∞ S2218H: 54.61 cm (21.5 inch) viewable area display (measured diagonally). 1920 x 1080 resolution, plus full-screen support for lower resolutions.
∞∞ TCO-Certified Displays. ∞∞ BFR/PVC-Reduced (Its circuit boards are made from BFR/PVC-free laminates). ∞∞ High Dynamic Contrast Ratio (8,000,000:1). ∞∞ 0.3 W standby power when in the sleep mode. ∞∞ Energy Gauge shows the energy level being consumed by the monitor in real time. ∞∞ Optimize eye comfort with a flicker-free screen and ComfortView feature which minimizes blue light emission.
Identifying Parts and Controls Front View 1 2 Front panel controls Label Description 1 Function buttons (For more information, see Operating your Monitor) 2 Power On/Off button (with LED indicator) NOTE: For displays with glossy bezels the user should consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces.
Back View 4 S2218H 12V 3.33A 5 S2218Hc S2218H 12V 3.33A S2218Hc 1 2 3 Back View without monitor stand Label Description Back View with monitor stand Use 1 Security-lock slot Secures monitor with security lock (security lock not included). 2 Regulatory label (including Barcode serial number and Service Tag label) Lists the regulatory approvals. Refer to this label if you need to contact Dell for technical support.
Side View Bottom View 1 23 4 5 Bottom view without monitor stand Label Description Use 1 Power-adapter port To connect the monitor power cable using a 12V DC adapter for transition. 2 Audio Line Out port Connect to external speakers (Optional Purchase)* 3 Audio Line In port Connects the audio cable (Optional Purchase) from the source device to the monitor. 4 HDMI port To connect your computer to the monitor using an HDMI cable.
Plug and Play Capability You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. Most monitor installations are automatic, you can select different settings if desired. For more information about changing the monitor settings, see Operating your Monitor.
Setting Up the Monitor Connecting the Stand NOTE: The stand is detached when the monitor is shipped from the factory. NOTE: The following steps is applicable for a monitor with a stand. 1 2 1 To attach the monitor stand: 1. Fit the stand riser and stand base together, and then turn the screw in the stand base. 2. Fit the two tabs on the upper part of the stand to the groove on the back of the monitor. Press the stand until it snaps into place.
Connecting Your Monitor WARNING: Before you begin any of the procedures in this section, follow the Safety Instructions. NOTE: Do not connect all cables to the computer at the same time. To connect your monitor to the computer: 1. Turn Off your computer and disconnect the power cable. 2. Connect the VGA/HDMI/audio cable from your monitor to the computer.
Connecting the audio cable(Optional Purchase) Organizing Cables After you connect all necessary cables to your monitor and computer, organize all cables as shown above. NOTE: After the cables are connected, they will have to be disconnected again to route them through the hole.
Removing the Monitor Stand NOTE: To prevent scratches on the LCD screen while removing the stand, ensure that the monitor is placed on a soft and clean surface. NOTE: The following steps is applicable for a monitor with a stand. 2 2 3 To remove the stand: 1. Place the monitor on a soft cloth or cushion. 2. Use a long and thin screwdriver to push the release latch. 3. Once the latch is released, remove the base away from monitor.
Operating Your Monitor Power On the Monitor Press the button to turn On the monitor. Using the Front Panel Controls Use the control buttons on the front of the monitor to adjust the image being displayed.
Front Panel Button Description 1 Use this button to choose from a list of preset modes. Shortcut key/Preset Modes Use the buttons to adjust the volume. Minimum is ‘0’ (-). Maximum is ‘100’ (+). Shortcut key/Volume Menu Use the MENU button to launch the On-Screen Display (OSD) and select the OSD Menu. See Accessing the OSD menu. Use this button to go back to the main menu or exit the OSD main menu. Exit Use the Power button to turn the monitor On and Off.
Use the Down button to adjust (decrease ranges) items in the OSD menu. 2 Down Use the OK button to confirm your selection. 3 OK Use the Back button to go back to the previous menu.
Using the On-Screen Display (OSD) Menu Accessing the OSD menu NOTE: If you change the settings and then either proceed to another menu or exit the OSD menu, the monitor automatically saves those changes. The changes are also saved if you change the settings and then wait for the OSD menu to disappear. 1. Press the button to display the OSD main menu.
Icon Menu and Submenus Description Brightness/ Contrast Use this menu to activate Brightness/Contrast adjustment. Dell S2X18H/HX Energy Use Brightness / Contrast Auto Adjust Input Source Color Display Audio 75% 75% Energy Menu Personalize Others Resolution: 1920x1080, 60Hz Brightness Brightness adjusts the luminance of the backlight. Press the button to increase the brightness and press the button to decrease the brightness (min. 0 / max. 100).
Auto Adjust Use this key to activate automatic setup and adjust menu. Dell S2X18H/HX Energy Use Brightness / Contrast Auto Adjust Press to adjust the screen automatically. Input Source Color Display Audio Energy Menu Personalize Others Resolution: 1920x1080, 60Hz The following dialog appears on a black screen as the monitor self-adjusts to the current input: Auto Adjustment in Progress... Auto Adjustment allows the monitor to self-adjust to the incoming video signal.
Color Use Color to adjust the color setting mode. Dell S2X18H/HX Brightness / Contrast Auto Adjust Input Source Energy Use Preset Modes Standard Input Color Format RGB Hue 50 Color Saturation 50 Display Reset Color Audio Energy Menu Personalize Others Resolution: 1920x1080, 60Hz Preset Modes When you select Preset Modes, you can choose Standard, ComfortView, Multimedia, Movie, Game, Warm, Cool or Custom Color from the list. ∞∞ Standard: Loads the monitor's default color settings.
Input Color Format Allows you to set the video input mode to: ∞∞ RGB: Select this option if your monitor is connected to a computer or DVD player using the HDMI cable. ∞∞ YPbPr: Select this option if your DVD player supports only YPbPr output.
Display Use the Display to adjust image.
Audio Dell S2318H/HX Energy Use Brightness / Contrast Volume 50 Auto Adjust Audio Source PC Audio Input Source Speaker Enable Color Reset Audio Display Audio Energy Menu Personalize Others Resolution: 1920x1080, 60Hz Volume Audio Source Use the buttons to adjust the volume. Minimum is ‘0’ (-). Maximum is ‘100’ (+). Allows you to set the Audio Source mode to: ∞∞ PC Audio ∞∞ HDMI Speaker Reset Audio Energy Allows you to enable or disable speaker function.
Menu Select this option to adjust the settings of the OSD, such as, the languages of the OSD, the amount of time the menu remains on screen and so on.
Personalize Users can choose a feature from Shortcut Key 1, Shortcut Key 2, Reset Personalization, Preset Modes or Brightness/ Contrast and set it as a shortcut key.
DDC/CI DDC/CI (Display Data Channel/Command Interface) allows your monitor parameters (brightness, color balance and etc.) to be adjustable via the software on your computer. You can disable this feature by selecting Disable. Enable this feature for best user experience and optimum performance of your monitor.
OSD Warning Messages When the Dynamic Contrast feature is enabled (in these preset modes: Game or Movie), the manual brightness adjustment is disabled. Dell S2X18H/HX To allow manual adjustment of brightness, the Energy Smart/Dynamic Contrast will be switched off. Do you want to continue? No Yes When the monitor does not support a particular resolution mode, the following message is displayed: Dell S2X18H/HX The current input timing is not supported by the monitor display.
If VGA or HDMI cable is not connected, a floating dialog box as shown below appears. The monitor will enter Power Save Mode after 4 minutes if left at this state. Dell S2X18H/HX ? No VGA Cable The display will go into Power Save Mode in 4 minutes. www.dell.com/support/monitors or Dell S2X18H/HX ? No HDMI Cable The display will go into Power Save Mode in 4 minutes. www.dell.com/support/monitors See Troubleshooting for more information.
Setting the Maximum Resolution To set the maximum resolution for the monitor: In Windows 7, Windows 8, Windows 8.1 and Windows 10: 1. For Windows 8 and Windows 8.1, select the Desktop tile to switch to classic desktop. 2. Right-click on the desktop and click Screen Resolution. 3. Click the Dropdown list of the Screen Resolution and select 1920 x 1080. 4. Click OK. If you do not see 1920 x 1080 as an option, you may need to update your graphics driver.
Using the Tilt NOTE: This is applicable for a monitor with a stand. When any other stand is bought, please refer to the respective stand setup guide for set up instructions. Rotating the Monitor Before you rotate the monitor, your monitor should be fully vertically extended and fully tilted up to avoid hitting the bottom edge of the monitor. NOTE: The stand is detached when the monitor is shipped from the factory.
Troubleshooting WARNING: Before you begin any of the procedures in this section, follow the Safety Instructions. Self-Test Your monitor provides a self-test feature that allows you to check if your monitor is functioning properly. If your monitor and computer are properly connected but the monitor screen remains dark, run the monitor self-test by performing the following steps: 1. Turn off both your computer and the monitor. 2. Disconnect the video cable from the back of the computer.
unplugged and the monitor is in self-test mode. 1 2 3 4 5 To run the built-in diagnostics: 1. Ensure that the screen is clean (no dust particles on the surface of the screen). 2. Unplug the video cable(s) from the back of the computer or monitor. The monitor then goes into the self-test mode. 3. Press and hold Button 1 for 5 seconds. A gray screen appears. 4. Carefully inspect the screen for abnormalities. 5. Press Button 1 on the bottom of the monitor again. The color of the screen changes to red. 6.
Common Problems The following table contains general information about common monitor problems you might encounter and the possible solutions: Common Symptoms What You Experience Possible Solutions No Video/Power LED off No picture ∞∞ Ensure that the video cable connecting the monitor and the computer is properly connected and secure. ∞∞ Verify that the power outlet is functioning properly using any other electrical equipment.
No sound or sound is low Monitor has no ∞∞ Make sure the audio cable is properly connected to the sound or sound monitor. is low ∞∞ Adjust the volume settings of both your monitor and computer. ∞∞ Make sure the computer sound card driver is properly installed and activated. ∞∞ Make sure the audio source is correct on the OSD. Horizontal/ Vertical Lines Screen has one or more lines ∞∞ Reset the monitor to Factory Settings(Factory Reset).
Video Ghosting or Overshooting Moving image ∞∞ Change the Response Time in the Display OSD to Fast appears to have or Normal depending on your application and usage. trailing shadow or bright edge.
Product-Specific Problems Specific Symptoms What You Experience Possible Solutions Screen image is too small Image is centered ∞∞ Check the Aspect Ratio setting in the Display on screen, but settings OSD. does not fill entire ∞∞ Reset the monitor to Factory Settings (Factory viewing area Reset) . Cannot adjust the monitor with the buttons on the side panel OSD does not appear on the screen ∞∞ Turn Off the monitor, unplug the power cord, plug it back, and then turn On the monitor.
Appendix WARNING: Safety Instructions WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards. WARNING: For displays with glossy bezels the user should consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces. For information on safety instructions, see the Product Information Guide. FCC Notices (U.S.
Setting Up Your Monitor Setting the display resolution For maximum display performance with Microsoft Windows operating systems, set the display resolution to 1920 x 1080 pixels by performing the following steps: In Windows 7, Windows 8, Windows 8.1 and Windows 10: 1. For Windows 8 and Windows 8.1, select the Desktop tile to switch to classic desktop. 2. Right-click on the desktop and click Screen Resolution. 3. Click the Dropdown list of the Screen Resolution and select 1920 x 1080. 4. Click OK.
7. After installing the drivers for your graphics adapter, attempt to set the resolution to 1920 x 1080 again. NOTE: If you are unable to set the recommended resolution, contact the manufacturer of your computer or consider purchasing a graphics adapter that will support the video resolution.
Monitor Specifications Flat Panel Specifications Model S2218H S2318H/S2318HX Screen type Active matrix - TFT LCD Active matrix - TFT LCD Panel type In-plane Switching In-plane Switching 54.61 cm (21.5 in) 58.42 cm (23 in) Viewable image Diagonal Horizontal, Active Area 476.06 mm (18.74 in) 509.18 mm (20.05 in) Vertical, Active Area 267.78 mm (10.54 in) 286.41 mm (11.28 in) Area 1274.79 cm2 (197.59 inch2) 1458.34 cm2 (226.04 inch2) Pixel pitch 0.248 mm 0.
Preset Display Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (Horizontal / Vertical) VESA, 720 x 400 31.5 70.1 28.3 -/+ VESA, 640 x 480 31.5 60.0 25.2 -/- VESA, 640 x 480 37.5 75.0 31.5 -/- VESA, 800 x 600 37.9 60.3 40.0 +/+ VESA, 800 x 600 46.9 75.0 49.5 +/+ VESA, 1024 x 768 48.4 60.0 65.0 -/- VESA, 1024 x 768 60.0 75.0 78.8 +/+ VESA, 1152 x 864 67.5 75.0 108.0 +/+ VESA, 1280 x 1024 64.0 60.0 108.
Model S2218H Signal cable type ∞∞ Digital: ∞∞ Digital: ∞∞ Digital: detachable, HDMI, detachable, detachable, 19 pins. HDMI, 19 pins. HDMI, 19 pins. S2318H S2318HX ∞∞ Analog: detachable, D-Sub, 15 pins ∞∞ Analog: ∞∞ Analog: detachable, detachable, D-Sub, 15 pins D-Sub, 15 pins Height 385.5 mm (15.18 in) 404.0 mm (15.90 in) 404.0 mm (15.90 in) Width 489.5 mm (19.27 in) 522.2 mm (20.56 in) 522.2 mm (20.56 in) Depth 147.9 mm (5.82 in) 147.9 mm (5.82 in) Dimensions (with stand) 147.9 mm (5.
Environmental Characteristics Model S2218H S2318H/S2318HX Temperature Operating 0°C to 40°C (32°F to 104°F) Non-operating Storage Shipping ∞∞ -20°C to 60°C (-4°F to 140°F) ∞∞ -20°C to 60°C (-4°F to 140°F) Humidity Operating 10% to 80% (non-condensing) Non-operating ∞∞ Storage: 5% to 90% (non-condensing) ∞∞ Shipping: 5% to 90% (non-condensing) Altitude Operating (maximum) 5,000 m (16,400 ft) Non-operating (maximum) 12,192 m (40,000 ft) Thermal dissipation ∞∞ 102.
Energy Star Power Consumption PON ETEC 16 W 50.59 Kwh S2318H/S2318HX VESA Modes Horizontal Sync Vertical Sync Active Video Active Power Indicator White Power Consumption Normal operation Active 34 W (maximum) Active-off mode Inactive Inactive Blanked White (Glowing ) Less than 0.3 W Switch off - - - Off Less than 0.3 W 23 W (typical) Energy Star PON ETEC Power Consumption 16 W 50.81 Kwh PON: Power consumption of on mode as defined in Energy Star 7.0 version.
Speaker Specifications Model S2218H/S2318H/S2318HX Speaker rated power Frequency Response Impedance 2x3W 200 Hz - 20 kHz 8 ohm The OSD functions only in the normal operation mode. When any button is pressed in the Active-off mode, the following message will be displayed: Dell S2X18H/HX There is no signal coming from your computer. Press any key on the keyboard or move the mouse to wake it up.
Pin Assignments VGA Connector Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15-pin Side of the Connected Signal Cable Video-Red Video-Green Video-Blue GND Self-test GND-R GND-G GND-B Computer 5V/3.
HDMI Connector Pin Number 1 2 3 4 5 19-pin Side of the Connected Signal Cable T.M.D.S. Data 2T.M.D.S. Data 2 Shield T.M.D.S. Data 2+ T.M.D.S. Data 1+ T.M.D.S. Data 1 Shield 6 7 8 9 10 11 12 13 14 15 16 17 18 19 T.M.D.S. Data 1 T.M.D.S. Data 0+ T.M.D.S. Data 0 Shield T.M.D.S. Data 0T.M.D.S. Clock + T.M.D.S. Clock Shield T.M.D.S. Clock CEC Reserved (N.C.
