Release Notes
Table Of Contents
- Dell EMC PowerEdge Systems Running Red Hat Enterprise Linux 8 Release Notes
- Contents
- Release summary
- Compatibility
- New and enhanced in RHEL 8 release
- Important notes
- Fixes
- BIOS update does not complete when an update is performed using the Linux .BIN files
- Dmesg shows drm related call trace in RHEL 8.3
- Operating system crashes on servers with NVIDIA GPGPUs
- Dmesg and /var/log/messages display AMD-Vi related messages
- The status of the NetworkManager service may be inactive when RHEL 8.3 is rebooted
- Operating system crashes on AMD Rome CPU-based systems and with Intel E810 NIC
- The lvcreate command requests a response from the user when -wipesignature -yes parameters are passed
- The mdmonitor service displays an error during operating system installation
- The dmidecode utility displays the slot type as
for PCIe Gen 4 NVMe slots - The mcelog utility logs 'only decoding architectural errors' message in var/log/messages
- Disk drives part of MD RAID are not listed as installation destination by the installer
- Dell EMC OpenManage Storage Services utility fails to reconfigure the virtual disk
- Guest VMs with SRIOV VFs assigned take a long time to power on, and libvirt related errors are observed
- Dmesg displays Integrity Measurement Architecture (IMA) driver related-messages during system boot
- After every reboot, the network interface name changes
- Red Hat Enterprise Linux Version 8 installation wizard creates a duplicate bonding interface
- Servers with the AMD Rome processor display a CCP initialization failure message in dmesg
- PowerEdge servers with the AMD Rome processor fail to detect an NVMe drive after multiple hot plugs
- Operating system enters the dracut shell during boot
- System crashes when rebooted with SR-IOV-enabled QLogic cards
- After system reboot, Disk data format (DDF) devices are not listed in /proc/mdstat
- Updating NVMe firmware using the nvme-cli utility displays an error in dmesg
- Fatal error BDF 02:00.0 is detected with BCM574xx NICs
- NVMe devices are not detected after hot-plugging
- Linux operating system fails to detect the Intel x710 card
- Dmidecode displays OUT OF SPEC in Slot Type and Slot Length of SMBIOS system slots
- Custom partitioning fails with FC LUN
- When booting the system from iSCSI with Mellanox CX-4 and CX-5 adapters, the system reports csum failure message
- Red Hat Enterprise Linux 8 kernel panic is observed due to fatal hardware error
- Known issues
- System hangs when Intel tboot is used to boot the operating system
- The anaconda installer crashes while autoconfiguring disk partitions
- The version field in the output of the modinfo command for certain networking drivers is null
- NetworkManager may restart unexpectedly when creating greater than 256 VLAN devices configured with DHCP IP
- FCoE session is not reestablished after MX9116N switch is rebooted
- Dmesg displays error messages when NVMe device is surprise removed
- Status of the RAID 0 logical volume is displayed as Available when one of the members of the RAID array is surprise removed
- /proc/mdstat and mdadm -D commands display incorrect statuses when two NVMe devices are surprise removed from a RAID 5 MD array
- Dell Controlled Turbo feature is not functional
- Caps Lock key-press is not registered on the Dell PowerEdge iDRAC virtual console
- RHEL 8.3 installer does not automatically locate the source installation repository when only inst.stage2=hd boot option is used
- The output of the systemctl status command displays the status as thawing
- Advanced Configuration and Power Interface (ACPI) error messages displayed in dmesg
- Drivers available in OEMDRV drive are not installed during the operating system installation
- The Mellanox IB devices are listed under an incorrect device category on Red Hat Enterprise Linux 8
- The lspci utility is unable to read Vital Product Data (VPD) from QLogic QLE2692 adapter
- Driver dependency mismatch errors reported while installing out-of-box drivers on Red Hat Enterprise Linux 8.x
- Dmesg displays TPM and nvdimm related-messages in Red Hat Enterprise Linux 8.1
- Link Up message is observed when the NVMe device slot is powered off and the device is unplugged
- Mellanox InfiniBand adapters are listed in Bluetooth
- iscsiadm output displays STATIC in the iface.bootproto field when the network interface is configured to DHCP
- When system reboots, system stops responding at the end of the reboot process
- Unable to shut down RHEL 8 when you select Graceful shutdown option or when you press power button on the server
- RHEL 8 does not discover FCoE LUNs connected over Broadcom BCM57XXX NICs
- iSCSI LUN not discovered during RHEL 8 installation
- RHEL 8 installation fails on systems with Emulex OneConnect card
- Switching between runlevels fails
- Limitations
- Resources and support
- Contacting Dell EMC
The output of the systemctl status command displays
the status as thawing
Description: The output of the systemctl status <service name> command displays the status Active:
active (running) (thawing) instead of Active: active (running) when a service is
reloaded. This issue is a cosmetic issue and can be ignored.
Applies to: Red Hat Enterprise Linux 8.3
Systems
affected:
Dell EMC PowerEdge yx4x and yx5x servers
Tracking number: 178127
Advanced Configuration and Power Interface (ACPI)
error messages displayed in dmesg
Description: The following ACPI-related error messages are displayed in dmesg and /var/log/messages:
[ 10.265354] ACPI Error: No handler for Region [SYSI]
(ffff8f04edb31a20) [IPMI] (20130517/evregion-162)
[ 10.265359] ACPI Error: Region IPMI (ID=7) has no handler (20130517/
exfldio-305)
[ 10.265368] ACPI Error: Method parse/execution failed
[\_SB_.PMI0._GHL] (Node ffff8f106dea07e0), AE_NOT_EXIST (20130517/
psparse-536)
[ 10.265376] ACPI Error: Method parse/execution failed
[\_SB_.PMI0._PMC] (Node ffff8f106dea0720), AE_NOT_EXIST (20130517/
psparse-536)
[ 10.265381] ACPI Exception: AE_NOT_EXIST, Evaluating _PMC (20130517/
power_meter-753)
The error messages are related to the module dependency and module load order of the
acpi_power_meter and acpi_ipmi drivers.
Applies to: Red Hat Enterprise Linux 8 and later
Solution: The messages are informational and can be ignored. For more information, see Red Hat Enterprise Linux
Knowledge Base article 49225
Tracking number: 172165
Drivers available in OEMDRV drive are not installed
during the operating system installation
Description:
Intermittently, during the installation of Red Hat Enterprise Linux, the operating system cannot enumerate
the USB drive at the stage of driver disk probing. This prevents the drivers from LC/OEMDRV from being
installed.
Applies to: Red Hat Enterprise Linux 8 and later
Workaround: Use the kernel boot parameter command inst.dd=LABEL=OEMDRV to install the drivers in the OEMDRV
drive.
Systems
affected:
Dell EMC PowerEdge servers
Tracking number: 168569
26 Known issues