Release Notes
Table Of Contents
- Dell EMC PowerEdge Systems Running Red Hat Enterprise Linux 8 Release Notes
- Contents
- Release summary
- Compatibility
- New and enhanced in RHEL 8 release
- Important notes
- Fixes
- BIOS update does not complete when an update is performed using the Linux .BIN files
- Dmesg shows drm related call trace in RHEL 8.3
- Operating system crashes on servers with NVIDIA GPGPUs
- Dmesg and /var/log/messages display AMD-Vi related messages
- The status of the NetworkManager service may be inactive when RHEL 8.3 is rebooted
- Operating system crashes on AMD Rome CPU-based systems and with Intel E810 NIC
- The lvcreate command requests a response from the user when -wipesignature -yes parameters are passed
- The mdmonitor service displays an error during operating system installation
- The dmidecode utility displays the slot type as
for PCIe Gen 4 NVMe slots - The mcelog utility logs 'only decoding architectural errors' message in var/log/messages
- Disk drives part of MD RAID are not listed as installation destination by the installer
- Dell EMC OpenManage Storage Services utility fails to reconfigure the virtual disk
- Guest VMs with SRIOV VFs assigned take a long time to power on, and libvirt related errors are observed
- Dmesg displays Integrity Measurement Architecture (IMA) driver related-messages during system boot
- After every reboot, the network interface name changes
- Red Hat Enterprise Linux Version 8 installation wizard creates a duplicate bonding interface
- Servers with the AMD Rome processor display a CCP initialization failure message in dmesg
- PowerEdge servers with the AMD Rome processor fail to detect an NVMe drive after multiple hot plugs
- Operating system enters the dracut shell during boot
- System crashes when rebooted with SR-IOV-enabled QLogic cards
- After system reboot, Disk data format (DDF) devices are not listed in /proc/mdstat
- Updating NVMe firmware using the nvme-cli utility displays an error in dmesg
- Fatal error BDF 02:00.0 is detected with BCM574xx NICs
- NVMe devices are not detected after hot-plugging
- Linux operating system fails to detect the Intel x710 card
- Dmidecode displays OUT OF SPEC in Slot Type and Slot Length of SMBIOS system slots
- Custom partitioning fails with FC LUN
- When booting the system from iSCSI with Mellanox CX-4 and CX-5 adapters, the system reports csum failure message
- Red Hat Enterprise Linux 8 kernel panic is observed due to fatal hardware error
- Known issues
- System hangs when Intel tboot is used to boot the operating system
- The anaconda installer crashes while autoconfiguring disk partitions
- The version field in the output of the modinfo command for certain networking drivers is null
- NetworkManager may restart unexpectedly when creating greater than 256 VLAN devices configured with DHCP IP
- FCoE session is not reestablished after MX9116N switch is rebooted
- Dmesg displays error messages when NVMe device is surprise removed
- Status of the RAID 0 logical volume is displayed as Available when one of the members of the RAID array is surprise removed
- /proc/mdstat and mdadm -D commands display incorrect statuses when two NVMe devices are surprise removed from a RAID 5 MD array
- Dell Controlled Turbo feature is not functional
- Caps Lock key-press is not registered on the Dell PowerEdge iDRAC virtual console
- RHEL 8.3 installer does not automatically locate the source installation repository when only inst.stage2=hd boot option is used
- The output of the systemctl status command displays the status as thawing
- Advanced Configuration and Power Interface (ACPI) error messages displayed in dmesg
- Drivers available in OEMDRV drive are not installed during the operating system installation
- The Mellanox IB devices are listed under an incorrect device category on Red Hat Enterprise Linux 8
- The lspci utility is unable to read Vital Product Data (VPD) from QLogic QLE2692 adapter
- Driver dependency mismatch errors reported while installing out-of-box drivers on Red Hat Enterprise Linux 8.x
- Dmesg displays TPM and nvdimm related-messages in Red Hat Enterprise Linux 8.1
- Link Up message is observed when the NVMe device slot is powered off and the device is unplugged
- Mellanox InfiniBand adapters are listed in Bluetooth
- iscsiadm output displays STATIC in the iface.bootproto field when the network interface is configured to DHCP
- When system reboots, system stops responding at the end of the reboot process
- Unable to shut down RHEL 8 when you select Graceful shutdown option or when you press power button on the server
- RHEL 8 does not discover FCoE LUNs connected over Broadcom BCM57XXX NICs
- iSCSI LUN not discovered during RHEL 8 installation
- RHEL 8 installation fails on systems with Emulex OneConnect card
- Switching between runlevels fails
- Limitations
- Resources and support
- Contacting Dell EMC
System crashes when rebooted with SR-IOV-enabled
QLogic cards
Description When the system is rebooted with SR-IOV-enabled QLogic cards, the system crashes and generates a
coredump (vmcore) in /var/crash.
Applies to
Red Hat Enterprise Linux 7.6 and later
Cause: The system crash is due to an issue in the qede driver.
Workaround Disable SR-IOV before rebooting the system. To disable SR-IOV, run the following command:
echo0 > /sys/class/net/network inteface name/device/sriov_numfs
Solution: The issue is resolved in Red Hat Enterprise Linux 8.2
Systems affected All Dell EMC PowerEdge servers
Tracking number 151479, 152995, 152997
After system reboot, Disk data format (DDF) devices
are not listed in /proc/mdstat
Description:
Disk data format (DDF)-based MD virtual disk (VD) devices are not listed in the /proc/mdstat file, if
there are more than one MD VD devices, after rebooting the system.
Applies to:
Red Hat Enterprise Linux 7.6 and later
Cause: Not available
Workaround: After creating the MD VD devices and before rebooting the system, run the following command:
mdadm --detail --scan >> /etc/mdadm.conf
NOTE: Verify the file before system reboot to confirm that the MD VD devices created earlier are
not altered.
Systems
affected:
All Dell EMC PowerEdge servers
Tracking number: 152384
Updating NVMe firmware using the nvme-cli utility
displays an error in dmesg
Description:
When updating the NVMe firmware using nvme-cli, the error message Get FW SLOT INFO log
error is displayed. This issue occurs when the drive firmware receives a request to activate immediately
without reset. This message is not observed when you update the firmware using a Dell-provided
firmware update package. There is no functionality loss.
Applies to: Red Hat Enterprise Linux 8.1
Cause: Not available
Solution: The issue is resolved in Red Hat Enterprise Linux 8.2
Systems
affected:
Dell EMC PowerEdge yx4x and yx5x servers
Fixes 17