Users Guide
Table Of Contents
- Table of Contents
- Preface
- 1 Introduction
- 2 Installing and Launching
- 3 QCS CLI Commands
- General Syntax and Keywords
- Command List
- Commands by Item View
- Command Details
- Add (Team Configuration)
- Add Discovery Portal
- Add Host
- Add iSNS Server
- Add Target
- Boot Configuration
- Cable Diagnostics
- Configure Advanced Settings
- Configure Advanced FCoE Settings
- Configure Advanced Adapter Settings
- Configure Advanced Port Settings
- Configure iSCSI Boot
- Configure iSCSI Initiator
- Configure iSCSI Management
- Configure iSCSI Management (on a Linux Host)
- Configure iSCSI Secret
- Configure Licenses
- Configure Multifunction
- Configure Resource
- Configure SR-IOV
- Configure System TOE
- Create Multiple NPIV Ports
- Create NPIV Port
- Diagnostics
- Discover Host
- Fallback
- Help
- Information (Adapter)
- Information (Team)
- List (Targets)
- List Discovery Portals
- List iSNS Servers
- Log
- Login
- Logout
- Network Diagnostics
- Ping Test
- Quit
- Refresh
- Refresh All
- Refresh Discovery Portal
- Refresh iSNS Server
- Remove (Team)
- Remove All Hosts
- Remove Discovery Portal
- Remove Host
- Remove iSNS Server
- Remove Multiple NPIV Ports
- Remove NPIV Port
- Remove Persistent Target
- Remove Target
- Reset Session Statistics
- Reset Statistics
- Restore (Team)
- Save (Team)
- Select (Target)
- Session Statistics
- Sessions
- Show Selected (Target)
- Statistics
- Unassigned (Adapters)
- Upgrade (Firmware)
- Version
- Legacy Commands
- 4 QCS CLI Usage
- Using Interactive Mode
- Performing Management Tasks
- Listing Target Adapters of Different Views in CLI Mode
- Obtaining Context Help for each Command
- Switching Between Different Views of Target Adapters
- Selecting a Target for the Command to Operate On
- Selecting a Target in Interactive Mode
- Getting Information for a Selected Target
- Configuring Advanced Parameters for a Selected Target
- Displaying Licenses for a Selected Target
- Configuring the iSCSI Parameter for a Selected Target
- Configuring the Resource of a Selected Target
- Configuring OoB Management for a Selected Target
- Configuring Systoe for the System
- Getting Statistics for a Selected Target
- Resetting Statistics for a Selected Target
- Running Diagnostic Tests for a Selected Target
- Running a Cable Diagnostic Test for a Selected Target
- Running a Network Diagnostic Test for a Selected Target
- Connecting to an FCoE Target
- Connecting to an iSCSI Target
- Creating a Team Configuration
- Restoring a Team Configuration
- Saving a Team Configuration
- Removing One or More Teams
- Displaying Unassigned Adapters
- Switching Between Primary and Standby Adapters in a Team
- Connecting an iSCSI Target
- Refreshing a Host
- Performing Other Common Tasks
- A Security Considerations
- B Configuration File Examples
- C Third-party Licenses
- D Exit Codes
- E Revision History
- Glossary
3–QCS CLI Commands
Configure Resource
Doc No. TD-000971 Rev. 1
January 29, 2021 Page 73 Copyright © 2021 Marvell
iSCSICONN
Sets the “iSCSI Connections” to the number allowed in the range displayed in the
cfg Resource CONFIGURABLE command. It requires a numeric <value>.
iSCSIPT
Sets the “iSCSI Pending Task per Connection” to valid numbers specified in the
cfg Resource CONFIGURABLE command. It requires a numeric <value>.
TOEPROTOCOL
Sets the “TOE Protocol Type” to the valid settings specified in the cfg
Resource CONFIGURABLE command. It requires a <value> of either IPv4
or IPv6.
iSCSIPROTOCOL
Sets the “iSCSI Protocol Type” to the valid settings specified in the cfg
Resource CONFIGURABLE command. It requires a <value> of either IPv4
or IPv6.
MEMCONSUMPTION
Sets the “iSCSI Memory Consumption” to the valid settings specified in the cfg
Resource CONFIGURABLE command. This keyword applies only to 578xx
adapters. It requires the <value> to be a percentage from 25 percent to
100 percent, with increments of 25 percent.
TOERSS
Sets the “TOE RSS” to either Enable or Disable. This keyword applies only to
578xx adapters. It requires a <value> that can be either Enable or
Disable.
Notes Issuing the cfg Resource command without options displays all resource
reservation keys and their current settings.
Examples The following examples show the cfg Resource command.
To view the currently enabled protocols (TOE, NDIS L2 Ethernet, iSCSI offload
and FCoE offload) of a port (in Single Function mode) and other port settings,
issue the following command. Note that TOE is not supported on the Marvell
FastLinQ 41000/45000 Series Adapters. In addition, NPAR FCoE and iSCSI
offload is controlled by the NPAR XML file settings (see “NIC Partition
Configuration XML Files” on page 189).
qcscli -t VBD -f MAC -i 001018AD45E0 "cfg Resource"
QLogic Control Suite Command Line Interface Utility for Windows v17.0.7.0
.......................................................
Resource Reservations