Users Guide
Table Of Contents
- Table of Contents
- Preface
- 1 Introduction
- 2 Installing and Launching
- 3 QCS CLI Commands
- General Syntax and Keywords
- Command List
- Commands by Item View
- Command Details
- Add (Team Configuration)
- Add Discovery Portal
- Add Host
- Add iSNS Server
- Add Target
- Boot Configuration
- Cable Diagnostics
- Configure Advanced Settings
- Configure Advanced FCoE Settings
- Configure Advanced Adapter Settings
- Configure Advanced Port Settings
- Configure iSCSI Boot
- Configure iSCSI Initiator
- Configure iSCSI Management
- Configure iSCSI Management (on a Linux Host)
- Configure iSCSI Secret
- Configure Licenses
- Configure Multifunction
- Configure Resource
- Configure SR-IOV
- Configure System TOE
- Create Multiple NPIV Ports
- Create NPIV Port
- Diagnostics
- Discover Host
- Fallback
- Help
- Information (Adapter)
- Information (Team)
- List (Targets)
- List Discovery Portals
- List iSNS Servers
- Log
- Login
- Logout
- Network Diagnostics
- Ping Test
- Quit
- Refresh
- Refresh All
- Refresh Discovery Portal
- Refresh iSNS Server
- Remove (Team)
- Remove All Hosts
- Remove Discovery Portal
- Remove Host
- Remove iSNS Server
- Remove Multiple NPIV Ports
- Remove NPIV Port
- Remove Persistent Target
- Remove Target
- Reset Session Statistics
- Reset Statistics
- Restore (Team)
- Save (Team)
- Select (Target)
- Session Statistics
- Sessions
- Show Selected (Target)
- Statistics
- Unassigned (Adapters)
- Upgrade (Firmware)
- Version
- Legacy Commands
- 4 QCS CLI Usage
- Using Interactive Mode
- Performing Management Tasks
- Listing Target Adapters of Different Views in CLI Mode
- Obtaining Context Help for each Command
- Switching Between Different Views of Target Adapters
- Selecting a Target for the Command to Operate On
- Selecting a Target in Interactive Mode
- Getting Information for a Selected Target
- Configuring Advanced Parameters for a Selected Target
- Displaying Licenses for a Selected Target
- Configuring the iSCSI Parameter for a Selected Target
- Configuring the Resource of a Selected Target
- Configuring OoB Management for a Selected Target
- Configuring Systoe for the System
- Getting Statistics for a Selected Target
- Resetting Statistics for a Selected Target
- Running Diagnostic Tests for a Selected Target
- Running a Cable Diagnostic Test for a Selected Target
- Running a Network Diagnostic Test for a Selected Target
- Connecting to an FCoE Target
- Connecting to an iSCSI Target
- Creating a Team Configuration
- Restoring a Team Configuration
- Saving a Team Configuration
- Removing One or More Teams
- Displaying Unassigned Adapters
- Switching Between Primary and Standby Adapters in a Team
- Connecting an iSCSI Target
- Refreshing a Host
- Performing Other Common Tasks
- A Security Considerations
- B Configuration File Examples
- C Third-party Licenses
- D Exit Codes
- E Revision History
- Glossary
3–QCS CLI Commands
Configure Multifunction
Doc No. TD-000971 Rev. 1
January 29, 2021 Page 66 Copyright © 2021 Marvell
Notes To display the current configuration, issue the cfg multi-function
command without options.
Examples The following examples show the cfg multi-function command.
To view the adapter’s current multifunction mode, issue the following command:
qcscli -r 172.28.63.183 -u winuser1\Administrator -p abc@USA -t phyadapters -f
BDF -i 42:00 "cfg multi-function"
QLogic Control Suite Command Line Interface Utility for Windows v17.0.7.0
Adapter is in Single-Function mode.
To write multifunction settings from a saved XML file back to the adapter, issue the
following command:
qcscli -r 172.28.63.183 -u winuser1\Administrator -p abc@USA -t phyadapters
-f BDF -i 42:00 "cfg multi-function -c MF.xml"
QLogic Control Suite Command Line Interface Utility for Windows v17.0.7.0
You have to reboot the system for the settings to take effect.
To save the adapter’s current multifunction settings to an editable XML file, issue
the following command:
qcscli -r 172.28.63.183 -u winuser1\Administrator -p abc@USA -t phyadapters
-f BDF -i 42:00 "cfg multi-function -s MF1.xml"
QLogic Control Suite Command Line Interface Utility for Windows v17.0.7.0
Please wait while configurations are being saved...
To view a quad-port 10GbE 57840 adapter in NPAR mode, issue the following
command, which shows a switch-independent NIC partitioning (NPAR) or
Multi-Function configuration XML file:
qcscli -r 172.28.63.183 -u winuser1\Administrator -p abc@USA -t phyadapters
-f BDF -i 42:00 "cfg multi-function"
QLogic Control Suite Command Line Interface Utility for Windows v17.0.7.0
Multi-Function Info
------------------------------------
Multi-Function mode Multi-Function
Port 0
Flow Control Rx & Tx Enabled
Function 0
Ethernet/Ndis Enable
iSCSI Disable
FCoE Enable
Relative Bandwidth Weight (%) 0