Users Guide
Table Of Contents
- Table of Contents
- Preface
- 1 Introduction
- 2 Installing and Launching
- 3 QCS CLI Commands
- General Syntax and Keywords
- Command List
- Commands by Item View
- Command Details
- Add (Team Configuration)
- Add Discovery Portal
- Add Host
- Add iSNS Server
- Add Target
- Boot Configuration
- Cable Diagnostics
- Configure Advanced Settings
- Configure Advanced FCoE Settings
- Configure Advanced Adapter Settings
- Configure Advanced Port Settings
- Configure iSCSI Boot
- Configure iSCSI Initiator
- Configure iSCSI Management
- Configure iSCSI Management (on a Linux Host)
- Configure iSCSI Secret
- Configure Licenses
- Configure Multifunction
- Configure Resource
- Configure SR-IOV
- Configure System TOE
- Create Multiple NPIV Ports
- Create NPIV Port
- Diagnostics
- Discover Host
- Fallback
- Help
- Information (Adapter)
- Information (Team)
- List (Targets)
- List Discovery Portals
- List iSNS Servers
- Log
- Login
- Logout
- Network Diagnostics
- Ping Test
- Quit
- Refresh
- Refresh All
- Refresh Discovery Portal
- Refresh iSNS Server
- Remove (Team)
- Remove All Hosts
- Remove Discovery Portal
- Remove Host
- Remove iSNS Server
- Remove Multiple NPIV Ports
- Remove NPIV Port
- Remove Persistent Target
- Remove Target
- Reset Session Statistics
- Reset Statistics
- Restore (Team)
- Save (Team)
- Select (Target)
- Session Statistics
- Sessions
- Show Selected (Target)
- Statistics
- Unassigned (Adapters)
- Upgrade (Firmware)
- Version
- Legacy Commands
- 4 QCS CLI Usage
- Using Interactive Mode
- Performing Management Tasks
- Listing Target Adapters of Different Views in CLI Mode
- Obtaining Context Help for each Command
- Switching Between Different Views of Target Adapters
- Selecting a Target for the Command to Operate On
- Selecting a Target in Interactive Mode
- Getting Information for a Selected Target
- Configuring Advanced Parameters for a Selected Target
- Displaying Licenses for a Selected Target
- Configuring the iSCSI Parameter for a Selected Target
- Configuring the Resource of a Selected Target
- Configuring OoB Management for a Selected Target
- Configuring Systoe for the System
- Getting Statistics for a Selected Target
- Resetting Statistics for a Selected Target
- Running Diagnostic Tests for a Selected Target
- Running a Cable Diagnostic Test for a Selected Target
- Running a Network Diagnostic Test for a Selected Target
- Connecting to an FCoE Target
- Connecting to an iSCSI Target
- Creating a Team Configuration
- Restoring a Team Configuration
- Saving a Team Configuration
- Removing One or More Teams
- Displaying Unassigned Adapters
- Switching Between Primary and Standby Adapters in a Team
- Connecting an iSCSI Target
- Refreshing a Host
- Performing Other Common Tasks
- A Security Considerations
- B Configuration File Examples
- C Third-party Licenses
- D Exit Codes
- E Revision History
- Glossary
3–QCS CLI Commands
Configure Advanced Adapter Settings
Doc No. TD-000971 Rev. 1
January 29, 2021 Page 46 Copyright © 2021 Marvell
Configure Advanced Adapter Settings
Configures settings at the adapter level on some 41000 Series Adapters.
Syntax cfg Advanced
[[key] | [key=value]]
Keywords key
Specifies an adapter setting. The key is case insensitive and must be specified
within double quotes if it contains any spaces or special characters.
Key includes:
Port Mode
Valid values can be retrieved by issuing cfg advanced “Port Mode” at the
adapter level.
Notes This command configures the port mode of the adapter. The valid values
represent the supported port modes for the adapter in use. The adapter is
configured to the specific mode after a reboot (SET operation).
Examples The following example shows the cfg Advanced command for adapter
settings:
WIN-D0ICI9TJD0O\devcon\0\adapter>cfg advanced
Advanced
--------------
Port Mode: 4x25
WIN-D0ICI9TJD0O\devcon\0\adapter>cfg advanced "Port Mode"
Port Mode
--------------------------------------------
Current setting: 4x25
Valid settings: 1x100 (Default)
4x10
4x25
WIN-D0ICI9TJD0O\devcon\0\adapter>
Value Configuration
1x100 Single 100G port
4x25 Four ports with 25G speed
4x10 Four ports with 10G speed