Users Guide
Table Of Contents
- Table of Contents
- Preface
- 1 Introduction
- 2 Installing and Launching
- 3 QCS CLI Commands
- General Syntax and Keywords
- Command List
- Commands by Item View
- Command Details
- Add (Team Configuration)
- Add Discovery Portal
- Add Host
- Add iSNS Server
- Add Target
- Boot Configuration
- Cable Diagnostics
- Configure Advanced Settings
- Configure Advanced FCoE Settings
- Configure Advanced Adapter Settings
- Configure Advanced Port Settings
- Configure iSCSI Boot
- Configure iSCSI Initiator
- Configure iSCSI Management
- Configure iSCSI Management (on a Linux Host)
- Configure iSCSI Secret
- Configure Licenses
- Configure Multifunction
- Configure Resource
- Configure SR-IOV
- Configure System TOE
- Create Multiple NPIV Ports
- Create NPIV Port
- Diagnostics
- Discover Host
- Fallback
- Help
- Information (Adapter)
- Information (Team)
- List (Targets)
- List Discovery Portals
- List iSNS Servers
- Log
- Login
- Logout
- Network Diagnostics
- Ping Test
- Quit
- Refresh
- Refresh All
- Refresh Discovery Portal
- Refresh iSNS Server
- Remove (Team)
- Remove All Hosts
- Remove Discovery Portal
- Remove Host
- Remove iSNS Server
- Remove Multiple NPIV Ports
- Remove NPIV Port
- Remove Persistent Target
- Remove Target
- Reset Session Statistics
- Reset Statistics
- Restore (Team)
- Save (Team)
- Select (Target)
- Session Statistics
- Sessions
- Show Selected (Target)
- Statistics
- Unassigned (Adapters)
- Upgrade (Firmware)
- Version
- Legacy Commands
- 4 QCS CLI Usage
- Using Interactive Mode
- Performing Management Tasks
- Listing Target Adapters of Different Views in CLI Mode
- Obtaining Context Help for each Command
- Switching Between Different Views of Target Adapters
- Selecting a Target for the Command to Operate On
- Selecting a Target in Interactive Mode
- Getting Information for a Selected Target
- Configuring Advanced Parameters for a Selected Target
- Displaying Licenses for a Selected Target
- Configuring the iSCSI Parameter for a Selected Target
- Configuring the Resource of a Selected Target
- Configuring OoB Management for a Selected Target
- Configuring Systoe for the System
- Getting Statistics for a Selected Target
- Resetting Statistics for a Selected Target
- Running Diagnostic Tests for a Selected Target
- Running a Cable Diagnostic Test for a Selected Target
- Running a Network Diagnostic Test for a Selected Target
- Connecting to an FCoE Target
- Connecting to an iSCSI Target
- Creating a Team Configuration
- Restoring a Team Configuration
- Saving a Team Configuration
- Removing One or More Teams
- Displaying Unassigned Adapters
- Switching Between Primary and Standby Adapters in a Team
- Connecting an iSCSI Target
- Refreshing a Host
- Performing Other Common Tasks
- A Security Considerations
- B Configuration File Examples
- C Third-party Licenses
- D Exit Codes
- E Revision History
- Glossary
User’s Guide—QLogic Control Suite CLI
45000/41000 Series Adapters and Adapters Based on 578xx Controllers
Doc No. TD-000971 Rev. 1
January 29, 2021 Page 215 Copyright © 2021 Marvell
Layer 2
Refers to the data link layer of the multilay-
ered communication model, Open
Systems Interconnection (OSI). The
function of the data link layer is to move
data across the physical links in a network,
where a switch redirects data messages at
the layer 2 level using the destination MAC
address to determine the message desti-
nation.
LED
Light-emitting diode. Status indicator on a
switch, router, adapter, or other device.
light-emitting diode
See LED.
logical unit number
See LUN.
LUN
Logical unit number, a subdivision of a
SCSI target. It is the small integer handle
that differentiates an individual disk drive
or partition (volume) within a common
SCSI target device such as a disk array.
Technically, a LUN can be a single
physical disk drive, multiple physical disk
drives, or a portion (volume) of a single
physical disk drive. However, LUNs are
typically not entire disk drives but rather
virtual partitions (volumes) of a RAID set.
Using LUNs, the Fibre Channel host can
address multiple peripheral devices that
may share a common controller.
message signaled interrupts
See MSI, MSI-X.
MSI, MSI-X
Message signaled interrupts. One of two
PCI-defined extensions to support
message signaled interrupts (MSIs), in
PCI 2.2 and later and PCI Express. MSIs
are an alternative way of generating an
interrupt through special messages that
allow emulation of a pin assertion or
deassertion.
MSI-X (defined in PCI 3.0) allows a device
to allocate any number of interrupts
between 1 and 2,048 and gives each inter-
rupt separate data and address registers.
Optional features in MSI (64-bit
addressing and interrupt masking) are
mandatory with MSI-X.
N_Port
Node port. A port that connects by a
point-to-point link to either a single N_Port
or a single F_Port. N_Ports handle
creation, detection, and flow of message
units to and from the connected systems.
N_Ports are end ports in virtual
point-to-point links through a fabric, for
example, N_Port to F_Port to F_Port to
N_Port using a single Fibre Channel fabric
switch.
N_Port ID virtualization
See NPIV.
network interface card
See NIC.
NIC
Computer card installed to enable a
dedicated network connection.
NIC partitioning
See NPAR.
node port
See N_Port.