Users Guide
Table Of Contents
- Table of Contents
- Preface
- 1 Introduction
- 2 Installing and Launching
- 3 QCS CLI Commands
- General Syntax and Keywords
- Command List
- Commands by Item View
- Command Details
- Add (Team Configuration)
- Add Discovery Portal
- Add Host
- Add iSNS Server
- Add Target
- Boot Configuration
- Cable Diagnostics
- Configure Advanced Settings
- Configure Advanced FCoE Settings
- Configure Advanced Adapter Settings
- Configure Advanced Port Settings
- Configure iSCSI Boot
- Configure iSCSI Initiator
- Configure iSCSI Management
- Configure iSCSI Management (on a Linux Host)
- Configure iSCSI Secret
- Configure Licenses
- Configure Multifunction
- Configure Resource
- Configure SR-IOV
- Configure System TOE
- Create Multiple NPIV Ports
- Create NPIV Port
- Diagnostics
- Discover Host
- Fallback
- Help
- Information (Adapter)
- Information (Team)
- List (Targets)
- List Discovery Portals
- List iSNS Servers
- Log
- Login
- Logout
- Network Diagnostics
- Ping Test
- Quit
- Refresh
- Refresh All
- Refresh Discovery Portal
- Refresh iSNS Server
- Remove (Team)
- Remove All Hosts
- Remove Discovery Portal
- Remove Host
- Remove iSNS Server
- Remove Multiple NPIV Ports
- Remove NPIV Port
- Remove Persistent Target
- Remove Target
- Reset Session Statistics
- Reset Statistics
- Restore (Team)
- Save (Team)
- Select (Target)
- Session Statistics
- Sessions
- Show Selected (Target)
- Statistics
- Unassigned (Adapters)
- Upgrade (Firmware)
- Version
- Legacy Commands
- 4 QCS CLI Usage
- Using Interactive Mode
- Performing Management Tasks
- Listing Target Adapters of Different Views in CLI Mode
- Obtaining Context Help for each Command
- Switching Between Different Views of Target Adapters
- Selecting a Target for the Command to Operate On
- Selecting a Target in Interactive Mode
- Getting Information for a Selected Target
- Configuring Advanced Parameters for a Selected Target
- Displaying Licenses for a Selected Target
- Configuring the iSCSI Parameter for a Selected Target
- Configuring the Resource of a Selected Target
- Configuring OoB Management for a Selected Target
- Configuring Systoe for the System
- Getting Statistics for a Selected Target
- Resetting Statistics for a Selected Target
- Running Diagnostic Tests for a Selected Target
- Running a Cable Diagnostic Test for a Selected Target
- Running a Network Diagnostic Test for a Selected Target
- Connecting to an FCoE Target
- Connecting to an iSCSI Target
- Creating a Team Configuration
- Restoring a Team Configuration
- Saving a Team Configuration
- Removing One or More Teams
- Displaying Unassigned Adapters
- Switching Between Primary and Standby Adapters in a Team
- Connecting an iSCSI Target
- Refreshing a Host
- Performing Other Common Tasks
- A Security Considerations
- B Configuration File Examples
- C Third-party Licenses
- D Exit Codes
- E Revision History
- Glossary
D–Exit Codes
Doc No. TD-000971 Rev. 1
January 29, 2021 Page 208 Copyright © 2021 Marvell
QCSCLI_CANNOT_MATCH_MAC_ADDR 1030 Cannot find device using the specified MAC address
QCSCLI_NO_TEAM_TO_CONFIG 1031 No team to configure
QCSCLI_CANNOT_CREATE_TEAM 1032 Failure while creating team
QCSCLI_NO_LINK_FOR_IP_CFG 1033 No link is present in team to set IP address
QCSCLI_ONE_OR_MORE_CREATE_FAILED 1034 Creation of one or more teams failed
QCSCLI_TEAM_NO_MEMBER 1035 A team is required to have at least one valid member
QCSCLI_NO_BRCM_NIC_IN_TEAM 1036 Team requires at least one Marvell NIC
QCSCLI_ONLY_QLOGIC_NIC_FOR_VLAN 1037 Only Marvell-certified adapters are supported in VLAN
QCSCLI_CANNOT_SET_IPADDR 1038 Failed to assign IP address on the virtual adapter
QCSCLI_INVALID_CFG 1039 Invalid configuration
QCSCLI_SET_ADVANCE_PARAM_FAILED 1040 Failed to set advanced parameter
QCSCLI_INTERNAL_ERROR_INVALID_DATA 1041 Invalid or NULL data found
QCSCLI_INVALID_PARAMETER 1042 Invalid parameter; parameter is too few
QCSCLI_NIC_NOT_SUPPORTED 1043 The current NIC is not supported for this operation
QCSCLI_SET_ASF_FAILED 1044 Failed to set the ASF table
QCSCLI_SET_POWER_MGMT_FAILED 1045 Failed to set power management configuration
QCSCLI_INVALID_TARGET_CMD 1046 Command or target identifier is invalid
QCSCLI_NO_ISCSI_SESSIONS 1047 No iSCSI sessions exists on the system
Table D-1. QLogic Control Suite CLI Exit Codes (Continued)
Code Text
Code
Number
Meaning