Users Guide
Table Of Contents
- Table of Contents
- Preface
- 1 Introduction
- 2 Installing and Launching
- 3 QCS CLI Commands
- General Syntax and Keywords
- Command List
- Commands by Item View
- Command Details
- Add (Team Configuration)
- Add Discovery Portal
- Add Host
- Add iSNS Server
- Add Target
- Boot Configuration
- Cable Diagnostics
- Configure Advanced Settings
- Configure Advanced FCoE Settings
- Configure Advanced Adapter Settings
- Configure Advanced Port Settings
- Configure iSCSI Boot
- Configure iSCSI Initiator
- Configure iSCSI Management
- Configure iSCSI Management (on a Linux Host)
- Configure iSCSI Secret
- Configure Licenses
- Configure Multifunction
- Configure Resource
- Configure SR-IOV
- Configure System TOE
- Create Multiple NPIV Ports
- Create NPIV Port
- Diagnostics
- Discover Host
- Fallback
- Help
- Information (Adapter)
- Information (Team)
- List (Targets)
- List Discovery Portals
- List iSNS Servers
- Log
- Login
- Logout
- Network Diagnostics
- Ping Test
- Quit
- Refresh
- Refresh All
- Refresh Discovery Portal
- Refresh iSNS Server
- Remove (Team)
- Remove All Hosts
- Remove Discovery Portal
- Remove Host
- Remove iSNS Server
- Remove Multiple NPIV Ports
- Remove NPIV Port
- Remove Persistent Target
- Remove Target
- Reset Session Statistics
- Reset Statistics
- Restore (Team)
- Save (Team)
- Select (Target)
- Session Statistics
- Sessions
- Show Selected (Target)
- Statistics
- Unassigned (Adapters)
- Upgrade (Firmware)
- Version
- Legacy Commands
- 4 QCS CLI Usage
- Using Interactive Mode
- Performing Management Tasks
- Listing Target Adapters of Different Views in CLI Mode
- Obtaining Context Help for each Command
- Switching Between Different Views of Target Adapters
- Selecting a Target for the Command to Operate On
- Selecting a Target in Interactive Mode
- Getting Information for a Selected Target
- Configuring Advanced Parameters for a Selected Target
- Displaying Licenses for a Selected Target
- Configuring the iSCSI Parameter for a Selected Target
- Configuring the Resource of a Selected Target
- Configuring OoB Management for a Selected Target
- Configuring Systoe for the System
- Getting Statistics for a Selected Target
- Resetting Statistics for a Selected Target
- Running Diagnostic Tests for a Selected Target
- Running a Cable Diagnostic Test for a Selected Target
- Running a Network Diagnostic Test for a Selected Target
- Connecting to an FCoE Target
- Connecting to an iSCSI Target
- Creating a Team Configuration
- Restoring a Team Configuration
- Saving a Team Configuration
- Removing One or More Teams
- Displaying Unassigned Adapters
- Switching Between Primary and Standby Adapters in a Team
- Connecting an iSCSI Target
- Refreshing a Host
- Performing Other Common Tasks
- A Security Considerations
- B Configuration File Examples
- C Third-party Licenses
- D Exit Codes
- E Revision History
- Glossary
D–Exit Codes
Doc No. TD-000971 Rev. 1
January 29, 2021 Page 207 Copyright © 2021 Marvell
QCSCLI_CANNOT_OPEN_FILE 1011 Failed to open the file handle
QCSCLI_ERR_CANNOT_SET_IPADDR 1012 Failed to set IP address
QCSCLI_ERR_CANNOT_GET_NIC_PCI_INFO 1013 Failure retrieving NIC information
QCSCLI_ERR_RETRIEVE_IP_ADDR 1014 Error retrieving IP address information
QCSCLI_FAILED_GET_INFO 1015 Failed to get info from the data container
QCSCLI_WRONG_OPTION_FLAG 1016 General team configuration file parsing error
QCSCLI_EXCEEDMAXVLAN 1017 A maximum of 64 VLANs are allowed
QCSCLI_CANNOT_CREATE_LIVE_LINK 1018 LiveLink™ support applied only to the SLB team
QCSCLI_EXCEED_MAX_TARGET_IP 1019 LiveLink support allows up to four links
QCSCLI_TOO_MANY_PHY_NIC 1020 A maximum of eight NICs are allowed in a team
QCSCLI_CANNOT_CREATE_FECGEC_8023AD 1021 Cannot create FEC-GEC or 802.3ad team with standby adapter
QCSCLI_LL_IP_TARGET_IP_TYPE_MISMATCH 1022 Invalid IPv6 address
QCSCLI_INVALID_RANGE 1023 Value is out of range
QCSCLI_INVALID_INTERVAL 1024 Invalid probe retry frequency
QCSCLI_DUPLICATE_OPTION 1025 The same option has been specified previously
QCSCLI_DUPLICATE_MAC_ADDRESS 1026 Duplicate adapter physical MAC address
QCSCLI_DUPLICATE_VLANID 1027 Duplicate VLAN name
QCSCLI_TEAM_ALREADY_EXISTS 1028 Team with the specified name already exists
Table D-1. QLogic Control Suite CLI Exit Codes (Continued)
Code Text
Code
Number
Meaning