Users Guide
Table Of Contents
- Table of Contents
- Preface
- 1 Introduction
- 2 Installing and Launching
- 3 QCS CLI Commands
- General Syntax and Keywords
- Command List
- Commands by Item View
- Command Details
- Add (Team Configuration)
- Add Discovery Portal
- Add Host
- Add iSNS Server
- Add Target
- Boot Configuration
- Cable Diagnostics
- Configure Advanced Settings
- Configure Advanced FCoE Settings
- Configure Advanced Adapter Settings
- Configure Advanced Port Settings
- Configure iSCSI Boot
- Configure iSCSI Initiator
- Configure iSCSI Management
- Configure iSCSI Management (on a Linux Host)
- Configure iSCSI Secret
- Configure Licenses
- Configure Multifunction
- Configure Resource
- Configure SR-IOV
- Configure System TOE
- Create Multiple NPIV Ports
- Create NPIV Port
- Diagnostics
- Discover Host
- Fallback
- Help
- Information (Adapter)
- Information (Team)
- List (Targets)
- List Discovery Portals
- List iSNS Servers
- Log
- Login
- Logout
- Network Diagnostics
- Ping Test
- Quit
- Refresh
- Refresh All
- Refresh Discovery Portal
- Refresh iSNS Server
- Remove (Team)
- Remove All Hosts
- Remove Discovery Portal
- Remove Host
- Remove iSNS Server
- Remove Multiple NPIV Ports
- Remove NPIV Port
- Remove Persistent Target
- Remove Target
- Reset Session Statistics
- Reset Statistics
- Restore (Team)
- Save (Team)
- Select (Target)
- Session Statistics
- Sessions
- Show Selected (Target)
- Statistics
- Unassigned (Adapters)
- Upgrade (Firmware)
- Version
- Legacy Commands
- 4 QCS CLI Usage
- Using Interactive Mode
- Performing Management Tasks
- Listing Target Adapters of Different Views in CLI Mode
- Obtaining Context Help for each Command
- Switching Between Different Views of Target Adapters
- Selecting a Target for the Command to Operate On
- Selecting a Target in Interactive Mode
- Getting Information for a Selected Target
- Configuring Advanced Parameters for a Selected Target
- Displaying Licenses for a Selected Target
- Configuring the iSCSI Parameter for a Selected Target
- Configuring the Resource of a Selected Target
- Configuring OoB Management for a Selected Target
- Configuring Systoe for the System
- Getting Statistics for a Selected Target
- Resetting Statistics for a Selected Target
- Running Diagnostic Tests for a Selected Target
- Running a Cable Diagnostic Test for a Selected Target
- Running a Network Diagnostic Test for a Selected Target
- Connecting to an FCoE Target
- Connecting to an iSCSI Target
- Creating a Team Configuration
- Restoring a Team Configuration
- Saving a Team Configuration
- Removing One or More Teams
- Displaying Unassigned Adapters
- Switching Between Primary and Standby Adapters in a Team
- Connecting an iSCSI Target
- Refreshing a Host
- Performing Other Common Tasks
- A Security Considerations
- B Configuration File Examples
- C Third-party Licenses
- D Exit Codes
- E Revision History
- Glossary
B–Configuration File Examples
iSCSI Boot Configuration XML File
Doc No. TD-000971 Rev. 1
January 29, 2021 Page 178 Copyright © 2021 Marvell
iSCSI Boot Configuration XML File
The following sections show examples of iSCSI boot configuration XML files. For
details about the command, see “Boot Configuration” on page 35.
iSCSI Example Configuration File for Adapters Based on
578xx Controllers
<?xml version="1.0" encoding="UTF-8"?>
<iSCSIBootConfiguration>
<QCScli><Version>30.0.56.0</Version></QCScli>
<iSCSIGeneral>
<TCPIPviaDHCP>Disabled</TCPIPviaDHCP>
<iSCSIPviaDHCP>Disabled</iSCSIPviaDHCP>
<CHAPAuthentication>Disabled</CHAPAuthentication>
<BoottoiSCSITarget>Enabled</BoottoiSCSITarget>
<DHCPVendorID>QLGCISAN</DHCPVendorID>
<LinkUpDelayTime>0</LinkUpDelayTime>
<UseTCPTimestamp>Disabled</UseTCPTimestamp>
<TargetasFirstHDD>Disabled</TargetasFirstHDD>
<LUNBusyRetryCount>0</LUNBusyRetryCount>
<IPVersion>IPv4</IPVersion>
VLANID 1–4094
BootRetryCount 0–7
a
For 41000/45000 Series Adapters, only the last saved BootProtocol setting is used.
If the
BootProtocol is set to iBFT, set the iSCSI Boot Mode to Non-Offload
and the iSCSI BootProtocol to iSCSI (see Table B-3 on page 183).
b
The iSCSI Boot protocol applies to boot or iBFT.
c
For software iSCSI boot, set the BootProtocol to iBFT and the iSCSI boot configuration
BootMode to Non-Offload (see Table B-3 on page 183).
For hardware iSCSI boot, set the
BootProtocol to iSCSI Boot and the iSCSI boot
configuration
BootMode to Offload (see Table B-3 on page 183).
d
For PXE boot, ensure that the LinkSpeed is the same value on both ports.
e
SmartAN(TM) is supported as a LinkSpeed value on some FastLinQ 45000 Series
Adapters.
Table B-1. MBA Configuration Parameters (Continued)
Parameter Value Range