Users Guide
Table Of Contents
- Table of Contents
- Preface
- 1 Introduction
- 2 Installing and Launching
- 3 QCS CLI Commands
- General Syntax and Keywords
- Command List
- Commands by Item View
- Command Details
- Add (Team Configuration)
- Add Discovery Portal
- Add Host
- Add iSNS Server
- Add Target
- Boot Configuration
- Cable Diagnostics
- Configure Advanced Settings
- Configure Advanced FCoE Settings
- Configure Advanced Adapter Settings
- Configure Advanced Port Settings
- Configure iSCSI Boot
- Configure iSCSI Initiator
- Configure iSCSI Management
- Configure iSCSI Management (on a Linux Host)
- Configure iSCSI Secret
- Configure Licenses
- Configure Multifunction
- Configure Resource
- Configure SR-IOV
- Configure System TOE
- Create Multiple NPIV Ports
- Create NPIV Port
- Diagnostics
- Discover Host
- Fallback
- Help
- Information (Adapter)
- Information (Team)
- List (Targets)
- List Discovery Portals
- List iSNS Servers
- Log
- Login
- Logout
- Network Diagnostics
- Ping Test
- Quit
- Refresh
- Refresh All
- Refresh Discovery Portal
- Refresh iSNS Server
- Remove (Team)
- Remove All Hosts
- Remove Discovery Portal
- Remove Host
- Remove iSNS Server
- Remove Multiple NPIV Ports
- Remove NPIV Port
- Remove Persistent Target
- Remove Target
- Reset Session Statistics
- Reset Statistics
- Restore (Team)
- Save (Team)
- Select (Target)
- Session Statistics
- Sessions
- Show Selected (Target)
- Statistics
- Unassigned (Adapters)
- Upgrade (Firmware)
- Version
- Legacy Commands
- 4 QCS CLI Usage
- Using Interactive Mode
- Performing Management Tasks
- Listing Target Adapters of Different Views in CLI Mode
- Obtaining Context Help for each Command
- Switching Between Different Views of Target Adapters
- Selecting a Target for the Command to Operate On
- Selecting a Target in Interactive Mode
- Getting Information for a Selected Target
- Configuring Advanced Parameters for a Selected Target
- Displaying Licenses for a Selected Target
- Configuring the iSCSI Parameter for a Selected Target
- Configuring the Resource of a Selected Target
- Configuring OoB Management for a Selected Target
- Configuring Systoe for the System
- Getting Statistics for a Selected Target
- Resetting Statistics for a Selected Target
- Running Diagnostic Tests for a Selected Target
- Running a Cable Diagnostic Test for a Selected Target
- Running a Network Diagnostic Test for a Selected Target
- Connecting to an FCoE Target
- Connecting to an iSCSI Target
- Creating a Team Configuration
- Restoring a Team Configuration
- Saving a Team Configuration
- Removing One or More Teams
- Displaying Unassigned Adapters
- Switching Between Primary and Standby Adapters in a Team
- Connecting an iSCSI Target
- Refreshing a Host
- Performing Other Common Tasks
- A Security Considerations
- B Configuration File Examples
- C Third-party Licenses
- D Exit Codes
- E Revision History
- Glossary
4–QCS CLI Usage
Performing Management Tasks
Doc No. TD-000971 Rev. 1
January 29, 2021 Page 158 Copyright © 2021 Marvell
Running a Network Diagnostic Test for a Selected Target
CLI Mode
Issue the following command to run a cable diagnostics test for the selected
target. This command is available for NDIS and virtual adapters:
QCSCLI -t <target type> -f <target format> -i <target ID>
networkdiag [-p <IP address>]
Examples:
QCSCLI -t NDIS -f mac -i 0010181a1b1c "networkdiag -p
192.168.1.5" runs the network test for the currently selected NDIS adapter.
QCSCLI -t VNIC -f mac -i 0010181a1b1c "networkdiag" runs the
network test for the currently selected virtual adapter. Because no IP address is
specified, QCS CLI uses the gateway address for the test.
Interactive Mode
Issue the list <view> and select <idx> commands to select the target
device. Then issue networkdiag [-p <IP address>] to run cable
diagnostics test for the selected target.
Examples:
networkdiag -p 192.168.1.5 runs the network test for the currently
selected NDIS adapter.
networkdiag runs the network test for the currently selected virtual adapter.
Connecting to an FCoE Target
CLI Mode
N/A
Interactive Mode
Content unavailable at the time of publication.
Connecting to an iSCSI Target
CLI Mode
N/A
Interactive Mode
Issue the list devcon, adddiscoveryportal, listdiscoveryportals,
and list iscsitargets commands. Then select an iSCSI target, login
to the target, and list iscsitargets again to ensure that it is connected.
Lastly, check the iSCSI target and session info.
Example:
list devcon