Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I QConvergeConsole VMware vCenter Server Plug-in
- 1 vCenter Server Plug-in Overview
- 2 Installing the vCenter Server Plug-in
- 3 Getting Started with vCenter Server Plug-in
- 4 Using the vCenter Server Plug-in
- Managing Hosts
- Managing Fibre Channel Adapters
- Adapter Management Window
- Managing a Fibre Channel Adapter Port
- Boot Configuration—Fibre Channel Port
- Firmware Parameters—Fibre Channel Port
- Transceiver Information—Fibre Channel Port
- Statistics Information—Fibre Channel Port
- Diagnostic Tests—Fibre Channel Port
- Retrieving Adapter Information
- VPD Information—Fibre Channel Port
- Temperature Information—Fibre Channel Port
- QoS Information—Fibre Channel Port
- Managing Converged Network Adapters
- Viewing Target Device Information
- Viewing LUN Information
- Updating Adapter Flash
- 5 Managing Marvell 578xx and 41000 Series Adapters
- Viewing Host Maps
- Managing 578xx/41000 Series Adapters
- Viewing Port Information for 578xx/41000 Series Adapters
- Configuring Port Boot Options
- Running Adapter Port Diagnostics
- Viewing Function Information for 578xx/41000 Series Adapters
- Viewing iSCSI Information for 578xx/41000 Series Adapters
- Viewing Information for an iSCSI Target Connected to 578xx/41000 Series Adapters
- Viewing Information for an iSCSI LUN Connected to 578xx/41000 Series Adapters
- Part II QConvergeConsole VMware vSphere Web Client Plug-in
- 7 vSphere Web Client Plug-in Overview
- 8 Installing the vSphere Web Client Plug-in
- 9 Getting Started with vSphere Web Client Plug-in
- 10 Using the vSphere Web Client Plug-in
- Managing Hosts
- Managing Adapters
- Managing NIC (Ethernet) Ports
- Managing Fibre Channel Ports
- Using the Fibre Channel Port Test Beacon
- Configuring Fibre Channel Port Boot Parameters
- Configuring Fibre Channel Port Parameters
- Viewing Fibre Channel Port Transceiver Information
- Viewing Fibre Channel Port Statistics
- Running Fibre Channel Port Diagnostics
- Viewing Fibre Channel Port VPD
- Viewing Fibre Channel Port Temperature Information
- Viewing Fibre Channel QoS Information
- Managing Converged Network Adapter Ports
- Managing NIC Functions
- Managing FCoE Functions
- Configuring FCoE Function NPAR Function Type
- Configuring FCoE Function Boot Parameters
- Configuring FCoE Function Parameters
- Viewing FCoE Function Transceiver Information
- Viewing FCoE Function Statistics
- Running FCoE Function Diagnostics
- Configuring the FCoE Function
- Viewing FCoE Function Temperature Information
- Viewing FCoE Function VPD
- Viewing FCoE Function Target Information
- Viewing FCoE Function LUN Information
- Managing iSCSI Functions
- 11 Managing Marvell 578xx and 41000 Series Adapters
- Managing Hosts
- Managing 578xx/41000 Series Adapters
- Viewing Port Information for 578xx/41000 Series Adapters
- Configuring Port Boot Options
- Running Adapter Port Diagnostics
- Viewing Function Information for 578xx/41000 Series Adapters
- Viewing iSCSI Information for 578xx/41000 Series Adapters
- Viewing Information for an iSCSI Target Connected to 578xx/41000 Series Adapters
- Viewing Information for an iSCSI LUN Connected to 578xx/41000 Series Adapters
- A Installing the QLogic Adapter CIM Provider Using VUM
- B Troubleshooting
- C Revision History
- Glossary
- Index
11–Managing Marvell 578xx and 41000 Series Adapters
Managing 578xx/41000 Series Adapters
Doc. No. TD-000965 Rev. 1
January 21, 2021 Page 216 Copyright © 2021 Marvell
Figure 11-17. Temperature Page (HTML5 based vSphere Client Plug-in)
QinQ Configuration
For specific Marvell 578xx Series 1/10Gbps Ethernet Adapters that have the QinQ
option enabled, you can use the QinQ tab at the adapter level to configure QinQ
for VLAN IDs on a per physical function (PF) basis.
QinQ is an implementation of the IEEE 802.1ad (or Q-in-Q) specification. QinQ
further segregates traffic by allowing the creation of VLANs within a VLAN by
adding an additional 802.1Q tag (VLAN ID field) to the Ethernet frames.
To configure QinQ:
1. In the adapter tree, select the 578xx Series Adapter node.
2. In the content pane, click the QinQ tab to view the QinQ Configuration page.
If the QinQ tab is not visible, QinQ is not enabled for your adapter model.