Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I QConvergeConsole VMware vCenter Server Plug-in
- 1 vCenter Server Plug-in Overview
- 2 Installing the vCenter Server Plug-in
- 3 Getting Started with vCenter Server Plug-in
- 4 Using the vCenter Server Plug-in
- Managing Hosts
- Managing Fibre Channel Adapters
- Adapter Management Window
- Managing a Fibre Channel Adapter Port
- Boot Configuration—Fibre Channel Port
- Firmware Parameters—Fibre Channel Port
- Transceiver Information—Fibre Channel Port
- Statistics Information—Fibre Channel Port
- Diagnostic Tests—Fibre Channel Port
- Retrieving Adapter Information
- VPD Information—Fibre Channel Port
- Temperature Information—Fibre Channel Port
- QoS Information—Fibre Channel Port
- Managing Converged Network Adapters
- Viewing Target Device Information
- Viewing LUN Information
- Updating Adapter Flash
- 5 Managing Marvell 578xx and 41000 Series Adapters
- Viewing Host Maps
- Managing 578xx/41000 Series Adapters
- Viewing Port Information for 578xx/41000 Series Adapters
- Configuring Port Boot Options
- Running Adapter Port Diagnostics
- Viewing Function Information for 578xx/41000 Series Adapters
- Viewing iSCSI Information for 578xx/41000 Series Adapters
- Viewing Information for an iSCSI Target Connected to 578xx/41000 Series Adapters
- Viewing Information for an iSCSI LUN Connected to 578xx/41000 Series Adapters
- Part II QConvergeConsole VMware vSphere Web Client Plug-in
- 7 vSphere Web Client Plug-in Overview
- 8 Installing the vSphere Web Client Plug-in
- 9 Getting Started with vSphere Web Client Plug-in
- 10 Using the vSphere Web Client Plug-in
- Managing Hosts
- Managing Adapters
- Managing NIC (Ethernet) Ports
- Managing Fibre Channel Ports
- Using the Fibre Channel Port Test Beacon
- Configuring Fibre Channel Port Boot Parameters
- Configuring Fibre Channel Port Parameters
- Viewing Fibre Channel Port Transceiver Information
- Viewing Fibre Channel Port Statistics
- Running Fibre Channel Port Diagnostics
- Viewing Fibre Channel Port VPD
- Viewing Fibre Channel Port Temperature Information
- Viewing Fibre Channel QoS Information
- Managing Converged Network Adapter Ports
- Managing NIC Functions
- Managing FCoE Functions
- Configuring FCoE Function NPAR Function Type
- Configuring FCoE Function Boot Parameters
- Configuring FCoE Function Parameters
- Viewing FCoE Function Transceiver Information
- Viewing FCoE Function Statistics
- Running FCoE Function Diagnostics
- Configuring the FCoE Function
- Viewing FCoE Function Temperature Information
- Viewing FCoE Function VPD
- Viewing FCoE Function Target Information
- Viewing FCoE Function LUN Information
- Managing iSCSI Functions
- 11 Managing Marvell 578xx and 41000 Series Adapters
- Managing Hosts
- Managing 578xx/41000 Series Adapters
- Viewing Port Information for 578xx/41000 Series Adapters
- Configuring Port Boot Options
- Running Adapter Port Diagnostics
- Viewing Function Information for 578xx/41000 Series Adapters
- Viewing iSCSI Information for 578xx/41000 Series Adapters
- Viewing Information for an iSCSI Target Connected to 578xx/41000 Series Adapters
- Viewing Information for an iSCSI LUN Connected to 578xx/41000 Series Adapters
- A Installing the QLogic Adapter CIM Provider Using VUM
- B Troubleshooting
- C Revision History
- Glossary
- Index
10–Using the vSphere Web Client Plug-in
Managing iSCSI Functions
Doc. No. TD-000965 Rev. 1
January 21, 2021 Page 196 Copyright © 2021 Marvell
5. In the iSCSI Parameters dialog box (Figure 10-60), click the IPv4 tab to
specify values for the IPv4 parameters, and then click OK.
Figure 10-60. iSCSI Function IPv4 Parameters
Alternatively, click General, Network, or IPv6 to configure other iSCSI
parameters.
iSCSI Function IPv6 Parameters
To configure IP parameters:
1. In the host system tree, expand an iSCSI port node to view the functions.
2. Select a function.
3. In the content pane on the Parameters page, click the IP Configuration
button to open the IPv4 and IPv6 Parameters page.
4. Click Edit.
5. In the iSCSI Parameters dialog box, click the IPv6 tab to specify values for
the IPv6 parameters, and then click OK.
Alternatively, click General, Network, or IPv4 to configure the other iSCSI
parameters.
Viewing iSCSI Function Statistics
To view function statistics
1. In the host system tree, expand an iSCSI port node to view the functions.
2. Select a function.