Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
5–Fibre Channel Noninteractive Commands
-qos (Quality of Service [QoS])
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 79 Copyright © 2021 Marvell
To view the link speed of a specific target attached to an adapter, issue the
following command:
qaucli -pr fc -q <hba instance>|<hba wwpn>|<target wwpn>
Where:
To set the link speed of all targets attached to one adapter or all adapters to the
designated speed, issue the following command:
qaucli -pr fc -q <hba instance>|<hba wwpn>|all -targets|-t
<speed>
Where:
To set the link speed of selected target(s) attached to one adapter to the
designated speed, issue the following command:
qaucli -pr fc -q <hba instance>|<hba wwpn>|all <target wwpn>
<speed>
Where:
-qos (Quality of Service [QoS])
<hba instance> = Adapter number (use the -g command to find)
<hba wwpn> = World wide port name of the adapter
<target wwpn> = World wide port name of the target
<hba instance> = Adapter number (use the -g command to find)
<hba wwpn> = World wide port name of the adapter
all = Reports link speed for all targets on all adapters in the system
-targets or -t = All targets
<speed> = Link speed
<hba instance> = Adapter number (use the -g command to find)
<hba wwpn> = World wide port name of the adapter
all = Reports link speed for all targets on all adapters in the system
<target wwpn> = World wide port name of the target
<speed> = Link speed
NOTE
The -qos option is supported on Marvell 8Gb, 16Gb, and 32Gb Fibre
Channel Adapters and Converged Network Adapters, and on Windows
Server 2008, Windows Server 2008 R2, Windows Server 2012, and
Windows Server 2012 R2 operating systems.