Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
5–Fibre Channel Noninteractive Commands
-o (Redirect Standard Output To a File)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 73 Copyright © 2021 Marvell
-o (Redirect Standard Output To a File)
Port down retry count PortDownRetryCount PD 0–255
Prefer FCP support
PreferFCP
l
FP 0 = Login to NVMe LUNs and
ignore FCP LUNs behind
the same target port.
1 = Login to FCP LUNs and
ignore NVMe LUNs behind
the same target port.
a
ConnectionOption is read-only for 10GbE (Marvell 3200/8100/8200 Series Adapters).
b
DataRate
applies to QLE2562 and 8100/8200 Series Adapters. It is read-only for 8100/8200 Series Adapters.
c
The NVRAM parameter EnableBIOS option is available only with Linux PPC64Le and Solaris x86.
d
The EnableFabricAssignWWN option applies to Marvell 2600 and 8300 Series Adapters.
e
Tape devices and Backup Protection Software must support persistent binding.
f
The HardLoopID option is not available for Marvell 8200 Series Adapters.
g
The Enable LR option enables long range (LR) cable distances in kilometers. For 2690 and 2700 Series Adapters,
select either 5Km or 10Km. For 2660 and 2500 Series Adapters, you can only select 10Km. The Enable LR option
is not available on 8200 Series Adapters.
h
The EnableUSCM option is supported only on 2770 Series Adapters and QLE269x Adapters.
i
The ExecutionThrottle option does not apply to 2600 and 8300 Series Adapters. Execution throttle is read-only
for 10GbE adapters.
j
The InterruptDelayTimer option is not available on Solaris.
k
The OperationMode option is not available on Solaris.
l
The PreferFCP option is available only for Marvell QLogic 2600 or 2700 Series Adapters. This option is for storage
that offers both FCP and NVMe LUNs.
NOTE
The -o option is valid only in noninteractive mode.
This option can be used with all noninteractive mode options that have a
corresponding interactive mode option (see Tab l e 5- 1 ). The option must
be the first or last command in the command line.
If the file already exists, new data are appended to the current file.
Table 5-9. Adapter Parameters (Continued)
Description Name Alias Value