Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
5–Fibre Channel Noninteractive Commands
-gs (Configure Parameters [Monitoring])
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 51 Copyright © 2021 Marvell
Port 2 WWPN 21-00-F4-E9-D4-54-AB-14 (HBA instance 5) Online (FEC)
HBA Model QLE2562 (SN GFC0819H89417):
Port 1 WWPN 21-00-00-1B-32-0C-A9-0B (HBA instance 2) SFP not present
Port 2 WWPN 21-01-00-1B-32-2C-A9-0B (HBA instance 3) SFP not present
HBA Model QLE2672 (SN RFE1303H21665):
Port 1 WWPN 21-00-00-0E-1E-11-60-D0 (HBA instance 0) Online
Port 2 WWPN 21-00-00-0E-1E-11-60-D1 (HBA instance 1) SFP not present
------------------------------------------------------------------------------
Total QLogic HBA(s) : 3
-gs (Configure Parameters [Monitoring])
To configure the adapter statistics, issue the -gs command as follows:
qaucli -pr fc -gs <hba instance>|<hba wwpn>
[<param name>|<param alias>) <param value>]
Where:
Table 5-5 lists the adapter statistics parameter names, aliases, and values.
The following restrictions apply:
Under Solaris, this feature is disabled if you are using the driver from the OS
installation CDs (QLC driver).
Under Linux, this feature is disabled if you are using the IOCTL driver.
<hba instance> = Adapter number (use the -g command to find)
<hba wwpn> = World wide port name of the adapter
<param name> = Name of the parameter
<param alias> = Alias of the parameter
<param value> = New value of the parameter
Table 5-5. Adapter Statistics Parameters
Description Name Alias Value
Sets how often statistics are retrieved AutoPoll AP
0–256
a
cycles
a
When the value is 0, statistics are retrieved automatically until you abort the operation. When the
value is in the range 1–256, statistics are retrieved for the number of cycles specified.
Sets the polling interval when retrieving statis-
tics
PollRate SR 5–30 seconds
Saves the adapter’s statistics to a CVS log file LogToFile LF Log file name