Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
5–Fibre Channel Noninteractive Commands
-fwdump (Firmware Dump)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 50 Copyright © 2021 Marvell
The following restrictions apply:
Under Solaris, the driver configuration feature is disabled if you are using the
driver from the OS installation CDs (QLC driver).
Under Linux, this feature is disabled if you are using the input/output control
(IOCTL) driver.
Under Mac OS
®
, the BindWWPN and BindPortID parameters are not
changeable; Mac OS supports only the BindWWPN parameter.
-fwdump (Firmware Dump)
To save the current adapter port firmware dump to a file, issue the following
command:
qaucli -pr fc -fwdump <hba instance>|<hba wwpn> <file name>
Where:
-g
To display host and adapter information on a local system, issue the -g
command. Example output is as follows:
------------------------------------------------------------------------------
Host Name : localhost
OS Type : Linux - SUSE Linux Enterprise Server 15 SP2
x86_64
OS Version : 5.3.18-22-default
FO API Version : 3.0.1 build9
SDM API Version : v6.04 build65
------------------------------------------------------------------------------
HBA Model QLE2772 (SN AFD1915Y07299):
Port 1 WWPN 21-00-F4-E9-D4-54-AB-12 (HBA instance 4) Online (FEC)
NOTE
To force a firmware dump file that can be collected and saved,
QConvergeConsole CLI requires a separate utility such as qlcna.exe.,
which is generally used for debugging purposes in the field by a Field
Application Engineer (FAE). To obtain this utility please contact Marvell
Technical Support.
<hba instance> = Adapter instance number of an adapter port (use the -g com-
mand to find)
<hba wwpn> = World wide port name of the adapter
<file name> = Name of the file to save the firmware dump to