Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
5–Fibre Channel Noninteractive Commands
-e (Boot Devices Configuration)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 42 Copyright © 2021 Marvell
For all operating systems, if the adapter already has boot devices selected and
they are the same as the ones in the command parameter or menu selection, the
following message appears:
The HBA already has that device selected as boot device.
To use selectable boot (the OS boots from the first target the BIOS finds) set the
<target wwpn>, <target wwnn>, and <lun id> inputs to all zeros. For
example issue the following command:
qaucli -pr fc -e <hba instance>|<hba wwpn> (enable | 0 0 0)
To disable (delete) the boot device for a specific adapter, issue the following
command:
qaucli -pr fc -e <hba instance>|<hba wwpn> disable
To set boot parameters for fabric-assigned boot LUNs, issue the following
commands:
qaucli -pr fc -e <hba instance>|<hba wwpn> <target wwnn> <target
wwpn> <lun id> [prim|alt1|alt2|alt3]
To configure the OS to boot from the first target that the BIOS finds (selectable
boot), issue the following command:
qaucli -pr fc -e <hba instance>|<hba wwpn> enable|0 0 0
To clear the selected current boot device settings on an adapter port (primary or
alternate boot port name), issue the following command:
qaucli -pr fc -e <hba instance>|<hba wwpn> disable
[prim|alt1|alt2|alt3]
To enable the fabric-assigned boot LUN setting, issue the following command:
qaucli -pr fc -e <hba instance>|<hba wwpn> enable
FabricAssignBootLUN | FB
To disable the fabric-assigned boot LUN setting, issue the following command:
qaucli -pr fc -e <hba instance>|<hba wwpn> disable
FabricAssignBootLUN | FB