Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
HBA Statistics
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 189 Copyright © 2021 Marvell
Default
5. Monitoring2. Fibre Channel Adapter1. HBA Statistics2. Default
From the HBA Statistics Menu, select Default to restore all HBA statistics settings
to their defaults.
Configure (-gs)
5. Monitoring2. Fibre Channel Adapter1. HBA Statistics3. Configure
From the HBA Statistics Menu, select Configure to open the Monitoring Config
Menu.
Monitoring Config Menu
1. Auto Poll
2. Set Rate
3. Enable Log
Auto Poll
5. Monitoring2. Fibre Channel Adapter1. HBA Statistics3. Configure1. Auto Poll
From the Monitoring Config Menu, select the Auto Poll option, and then select
either Enable Auto Poll or Disable Auto Poll.
Set Rate
5. Monitoring2. Fibre Channel Adapter1. HBA Statistics3. Configure2. Set Rate
From the Monitoring Config Menu, select the Set Rate option, and then for the
Sampling Rate (Seconds) setting, type a value between 5 and 30; the
current value is shown in brackets.
Enable Log
5. Monitoring2. Fibre Channel Adapter1. HBA Statistics3. Configure3. Enable Log
From the Monitoring Config Menu, select the Enable Log option to specify the
name of a log file in which to store HBA statistics for the selected port.
Run
5. Monitoring2. Fibre Channel Adapter1. HBA Statistics4. Run
From the HBA Statistics Menu, select Run to monitor port statistics. The following
shows example output:
------------------------------------------------------------------------------
HBA Instance 0: QLE2692 Port 1 WWPN 50-00-53-37-A1-52-C0-06 PortID 05-15-00
Link: Online (FEC)
------------------------------------------------------------------------------
Monitoring
-----------------------------------------