Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
Monitoring
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 188 Copyright © 2021 Marvell
Part Number: 57-1000333-01
Serial Number: JAF315410000FSU
Revision:
Date: 151007
---------------------------------
Optical Element Data Descriptor
---------------------------------
Descriptor Tag: Optical Element Data
Descriptor Length: 12 Bytes
High Alarm: 75.00
Optical Element Function Flag [0x00] High Alarm: 0x4b
Optical Element Function Flag [0x00] Low Alarm: 0xfffb
Optical Element Function Flag [0x00] High Warning: 0x46
Optical Element Function Flag [0x00] Low Warning: 0x00
Monitoring
5. Monitoring2. Fibre Channel Adapter
From the main menu, select the Monitoring option, and then select the adapter
type (Fibre Channel Adapter).
The Monitoring menu contains options for monitoring statistics for Host Bus
Adapters, HBA temperature, buffer-to-buffer credits, and congestion (UCSM).
HBA Statistics
5. Monitoring2. Fibre Channel Adapter1. HBA Statistics
From the Monitoring menu, select the HBA Statistics option, and then select an
adapter port. The HBA Statistics Menu provides options to display the current
configuration, reset the default configuration, change the configuration, and run
HBA statistics.
To reset all the driver statistics counters for the current session, press the R key
during run time.
Info
5. Monitoring2. Fibre Channel Adapter1. HBA Statistics1. Info
From the HBA Statistics Menu, select Info to view the current Monitor Settings for
the selected port, including AutoPoll (AP), SetRate (SR), and LogToFile (LF).