Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
Diagnostics Port Test (-dport)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 182 Copyright © 2021 Marvell
Configure
4. Adapter Diagnostics2. Fibre Channel Adapter10. Diagnostics Port Test 1. Configure
From the Diagnostics Port Config Menu, select one of the following options:
1. Disable Diagnostics Port
2. Enable Diagnostics Port
The currently selected mode (enabled or disabled) is indicated by (Current).
Run
4. Adapter Diagnostics2. Fibre Channel Adapter10. Diagnostics Port Test 2. Run
When you select Run, a warning message advises that running the Diagnostics
Port Test will put the port in offline mode and asks if you want to proceed. To
continue, select 1: Yes.
The following shows example test output from a Brocade switch:
Starting diagnostic port test of HBA 0 (QLE2740), please wait...
Start Time: Tue Jul 25 09:20:59 2017
End Time : Tue Jul 25 09:21:21 2017
------------------------------------------------------------------------------
HBA Instance 0: QLE2740 Port 1 WWPN 21-00-00-24-FF-00-27-D5 PortID 02-05-00
Link: Link Down
------------------------------------------------------------------------------
HBA Port Electrical Loopback Optical Loopback Link Traffic
NOTE
Currently Cisco does not support running diagnostics from the host server; it
only supports running the diagnostics test from the switch. For details, refer
to the Cisco user’s guide.
NOTE
Do not run dport when the switch port is configured in dport mode.
Before running diagnostics, ensure that the adapter is online by issuing the
following command:
#qaucli -g
HBA Model QLE2740 (SN AFD1533Y02970):
= Port 1 WWPN 21-00-00-24-FF-8F-C9-E0 (HBA instance 0)
Online (FEC)