Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
Diagnostics Port Test (-dport)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 181 Copyright © 2021 Marvell
Seq Proto Error
Invalid Trans Word
Run
4. Adapter Diagnostics2. Fibre Channel Adapter9. Link Status4. Run
From the FC Diagnostics menu, select the Link Status option, and then select
Run to start running a link status. Press ENTER to stop running the link status.
---------------------------------------
Link Status Settings
---------------------------------------
AutoPoll (AP): 10
SetRate (SR): 5
LogToFile (LF): null.csv
--------------------------------------------------------------------------------
HBA Instance 1: QLE2662 Port 2 WWPN 20-01-00-09-0C-00-FF-01 PortID 00-00-00
Link: SFP not installed
--------------------------------------------------------------------------------
Link Status
-------------------------------------------
General keyboard shortcuts:
R - Reset current
C - Refresh current
T - Refresh total
ENTER - Cancel the current task
-------------------------------------------
Port Name Link Sync Signal Invalid Seq Proto Invalid
Failure Loss Loss CRC Error Trans Word
----------------------- -------- -------- -------- -------- --------- ----------
20-01-00-09-0C-00-FF-01 0 0 0 0 0 0
--------------------------------------------------------------------------------
Diagnostics Port Test (-dport)
4. Adapter Diagnostics2. Fibre Channel Adapter10. Diagnostics Port Test
From the FC Adapter Diagnostics menu, select the Diagnostics Port Test option,
and then select a port with a link speed of 16Gbps or 32Gbps. The Diagnostics
Port Menu opens and lists options to configure and run port, electrical and optical
loopback, and link traffic diagnostics on the selected port. This option is not
supported on the Oracle Solaris platform.