Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
Link Status (-ls)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 180 Copyright © 2021 Marvell
Configure
4. Adapter Diagnostics2. Fibre Channel Adapter9. Link Status2. Configure
From the FC Adapter Diagnostics menu, select the Link Status option, select
Configure, to view the Link Status Config Menu with the following options:
Link Status Config Menu
1: Auto Poll
2: Set Rate
3: Enable Log
4: Default
Auto Poll
4. Adapter Diagnostics2. Fibre Channel Adapter9. Link Status2. Configure1. Auto Poll
From the Link Status Config Menu, select the Auto Poll option, and then select
either Enable Auto Poll or Disable Auto Poll.
Set Rate
4. Adapter Diagnostics2. Fibre Channel Adapter9. Link Status2. Configure2. Set Rate
From the Link Status Config Menu, select the Set Rate option, and then for the
Sampling Rate (Seconds) setting, type a value between 5 and 30; the
current value is shown in brackets.
Enable Log
4. Adapter Diagnostics2. Fibre Channel Adapter9. Link Status2. Configure3. Enable Log
From the Link Status Config Menu, select the Enable Log option to specify the
name of a log file in which to store link statistics for the selected port.
Default
4. Adapter Diagnostics2. Fibre Channel Adapter9. Link Status2. Configure4. Default
From the Link Status Config Menu, select the Default option to restore the default
settings for link statistics for the selected port.
Hard Reset
4. Adapter Diagnostics2. Fibre Channel Adapter9. Link Status3. Hard Reset
From the FC Adapter Diagnostics menu, select the Link Status option, and then
select Hard Reset to set to zero all of the counters in the firmware private
statistics data. When the command completes successfully, the following firmware
counters are cleared:
Link Failure
Sync Loss
Signal Loss
Invalid CRC