Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
CT Ping Test (-ctp)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 174 Copyright © 2021 Marvell
-----------------------------------------------------------------------------
Diagnostics Settings
--------------------
Diagnostic Mode : CT Ping
Number of tests (1-10000): 10
Test Increment(1-10000) : 1
Abort On Error : Ignore
Test Continuous : OFF
-----------------------------------------------------------------------------
Reset Test Parameters
4. Adapter Diagnostics2. Fibre Channel Adapter7. CT Ping Test2. Reset Test Parameters
From the CT Ping Test menu, select the Reset Test Parameters option to reset
the CT ping test parameters to the default values.
Configure Test Parameters
4. Adapter Diagnostics2. Fibre Channel Adapter7. CT Ping Test3. Configure Test Parameters
From the CT Ping Test menu, select the Configure Test Parameters option to
open the CT Ping Test submenu. The CT Ping Test menu lists options to configure
the quantity of tests and test increments, set abort on error, and enable or disable
devices. For detailed information about these parameters, see Table 5-3 on page
35.
For example:
=======================================================
HBA : 4 Port: 1
SN : AFD1915Y07299
HBA Model : QLE2772
HBA Desc. : QLogic QLE2772 2x32Gb QLE2772 FC HBA
FW Version : 9.06.02
WWPN : 21-00-F4-E9-D4-54-AB-12
WWNN : 20-00-F4-E9-D4-54-AB-12
Link : Online (FEC)
=======================================================
1: Number Of Test(s)
2: Test Increment(s)
3: Test Option
4: Enable/Disable Device(s)