Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
Read Write Buffer Test (-kr)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 163 Copyright © 2021 Marvell
Display Test Parameters (-kr)
4. Adapter Diagnostics2. Fibre Channel Adapter2. Read Writer Buffer Test<port selection>1. Display Test
Parameters
From the Read Write Buffer Test menu, select the Display Test Parameters
option to view the read write buffer test parameters. For example:
------------------------------------------------------------------
HBA Instance 1: QLE2692 Port 2 WWPN 21-00-00-24-FF-8F-D8-67 PortID
00-00-00
Link: D-Port
------------------------------------------------------------------
--------------------
Diagnostics Settings
--------------------
Diagnostic Mode : R/W Buffer
Data Pattern : Random
Data Size (Bytes) : 8
Number of tests (1-10000): 10
Test Increment(1-10000) : 1
Abort On Error : Ignore
Test Continuous : OFF
------------------------------------------------------------------
Reset Test Parameters
4. Adapter Diagnostics2. Fibre Channel Adapter2. Read Write Buffer Test<port selection>2. Reset Test
Parameters
From the Read Write Buffer Test menu, select the Reset Test Parameters option
to reset the read write buffer test parameters to their default values.
Configure Test Parameters (-kr)
4. Adapter Diagnostics2. Fibre Channel Adapter2. Read Write Buffer Test<port selection>3. Configure Test
Parameters
From the Read Write Buffer Test menu, select the Configure Test Parameters
option to open the Read Write Buffer Test submenu with options to configure the
data pattern, data size, number of tests, test increment, error handling, and
devices. For detailed information about these parameters, see Table 5-6 on page
64.