Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
Parameters Update (-r)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 154 Copyright © 2021 Marvell
Parameters Update (-r)
3. Adapter Updates2. Fibre Channel Adapter3. Parameters Update
From the FC Adapter Update menu, select the Parameters Update option. From
the port menu, select a port for which to specify the parameter update, and then
type the file name. For example:
Parameters Update
HBA Model QLE2692 SN: AFD1536Y03145
1: Port 1: WWPN: 21-00-00-24-FF-8F-D8-66 Online
2: Port 2: WWPN: 21-00-00-24-FF-8F-D8-67 D-Port
HBA Model QLE2740 SN: AFD1536Y03312
3: Port 1: WWPN: 21-00-00-24-FF-00-27-B3 SFP not installed
HBA Model QLE2662 SN: AFE1227F06193
4: Port 1: WWPN: 20-01-00-0E-1E-08-D9-A0 SFP not installed
5: Port 2: WWPN: 20-01-00-0E-1E-08-D9-A1 SFP not installed
(p or 0: Previous Menu; m or 98: Main Menu; ex or 99: Quit)
Please Enter Selection: 1
Enter a file name or Hit <RETURN> to abort:parameters_update
If the adapter does not support the parameter update option, a notification
message appears. For example:
(p or 0: Previous Menu; m or 98: Main Menu; ex or 99: Quit)
Please Enter Selection: 1
Option not supported with selected HBA (Instance 0 - QLE8362)!
Parameters Template Update
3. Adapter Updates2. Fibre Channel Adapter4. Parameters Template Update
This option appears only when an 8Gb FC adapter is selected. From the FC
Adapter Update menu, select the Parameters Template Update option. From the
port menu, select a port to open the HBA Parameters Templates Menu with
options for various adapter vendors. For example:
Parameters Template Update
HBA Model QLE2692 SN: AFD1536Y03145
1: Port 1: WWPN: 21-00-00-24-FF-8F-D8-66 Online
2: Port 2: WWPN: 21-00-00-24-FF-8F-D8-67 D-Port
HBA Model QLE2740 SN: AFD1536Y03312
3: Port 1: WWPN: 21-00-00-24-FF-00-27-B3 SFP not installed
HBA Model QLE2662 SN: AFE1227F06193