Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
Flash Update (-b)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 152 Copyright © 2021 Marvell
Updating Adapter Fw Preload Area version 4.0.10... Success
Updating Adapter PCIe Serdes version 03.00.04... Success
Updating Adapter FC Board Configs version 03.00.01... Success
Updating Adapter FC RISC Fw version 9.2.3... Success
Updating Adapter Flash Memo Block... Success
Updating Adapter Primary Image Status... Success
Updating Adapter Secondary Image Status... Success
Updating Adapter Primary Aux Image Status... Success
Updating Adapter Secondary Aux Image Status... Success
Flash update complete. You must reboot in order for the changes to
become effective.
Following is example output of a failed flash update:
c:\Program Files\QLogic Corporation\QConvergeConsoleCLI>qaucli.exe
-b 0 C:\Users\Administrator\Downloads\mh030215.bin
Using config file: c:\Program Files\QLogic
Corporation\QConvergeConsole CI
Working dir: c:\Program Files\QLogic
Corporation\QConvergeConsoleCLI
FW lockdown is enabled. Flash update is restricted to HBA
instance 0 (QLE2772)!
If System Lockdown Mode is turned on, the flash update fails if the existing
released driver/application is being run with the latest RISC/MPI firmware (that
supports the firmware lockdown feature).
If a new driver/RISC/MPI firmware is being run with the existing application, the
flash update fails with an error message that may be misleading, as the existing
application is not aware of the lockdown feature.
If an existing MPI/RISC firmware, driver, and application are being run, System
Lockdown Mode (on or off) has no effect. The flash update will be successful.
NOTE
For the 2770 Series, error 511 may indicate non-authentic firmware. See
fcscli-exitcodes.txt for error code details.
NOTE
On Solaris only:
Reset is disabled if the system detects storage SR-IOV or VFs.
The flash update does not take effect until the system is restarted.