Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
Flash Update (-b)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 151 Copyright © 2021 Marvell
6: FC Board Config Update
7: FC Firmware Dump
Flash Update (-b)
3. Adapter Updates2. Fibre Channel Adapter1. Flash Update
From the FC Adapter Update menu, select the Flash Update option. From the
adapter menu, select the adapter, and then type the Flash update file name.
2600/2700 Series Fibre Channel Adapter Selection:
Flash Update
1: HBA Model: QLE2692 SN: AFD1536Y03145
Port 1 WWPN: 21-00-00-24-FF-8F-D8-66 Online
Port 2 WWPN: 21-00-00-24-FF-8F-D8-67 D-Port
2: HBA Model: QLE2740 SN: AFD1536Y03312
Port 1 WWPN: 21-00-00-24-FF-00-27-B3 SFP not installed
3: HBA Model: QLE2662 SN: AFE1227F06193
Port 1 WWPN: 20-01-00-0E-1E-08-D9-A0 SFP not installed
Port 2 WWPN: 20-01-00-0E-1E-08-D9-A1 SFP not installed
(p or 0: Previous Menu; m or 98: Main Menu; ex or 99: Quit)
Please Enter Selection: 1
Enter a file name or Hit <RETURN> to abort: bkxxxxxx.bin
2770 Series Fibre Channel Adapter Flash Update Example:
Following is example output for a successful flash update:
Validating Flash Image File... Success
Updating Flash on HBA port(s) - QLE2772. Please wait...
Updating Adapter FC Boot Code... Success
EFI version: 07.06.00
Updating Adapter PEP softROM version 03.00.13... Success
Updating Adapter PEP FW version 03.00.22... Success
Updating Adapter PEP Board Configs version 03.01.00... Success
NOTE
The BIOS or FCode cannot be updated when the System Lockdown Mode
feature is enabled. Use “FC Adapter Information (-i)” on page 99 to view the
System Lockdown Mode status. Use the Dell Management Console
Dashboard to change the status. By default, the System Lockdown Mode
feature is enabled.