Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
Personality (-pc)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 147 Copyright © 2021 Marvell
Flash PEP Firmware Version : 2.00.08
Actual Connection Mode : Point to Point
Actual Data Rate : 16 Gbps
Device ISP ID : ISP2261
Chip Revision : 0x1(A0)
PortType (Topology) : NPort
Target Count : 0
PCI Bus Number : 5
PCI Device Number : 0
PCI Function Number : 0
PCI Device ID : 0x2261
Subsystem Device ID : 0x02a8
Subsystem Vendor ID : 0x1077
PCIe Max Bus Width : x8
PCIe Negotiated Width : x8
PCIe Max Bus Speed : 8.0 Gbps
PCIe Negotiated Speed : 8.0 Gbps
HBA Temperature (C) : 56
HBA Status : Online
------------------------------------------------------------------------------
HBA VPD Information
------------------------------------------------------------------------------
.
.
.
Personality (-pc)
2. Adapter Configuration2. FC Adapter Configuration13. Personality
From the FC Adapter Configuration menu, select the Personality option to set the
adapter personality to Fibre Channel only or Converged Network Adapter. From
the adapter menu, select the adapter whose personality is to be changed, and
then confirm your selection, as shown in the following examples.
NOTE
d ed
The personality feature is supported only on Marvell QLogic QLE267x and
QLE836x Adapters. This feature lets you set the adapter’s personality to
Fibre Channel only or Converged Network Adapter.