Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
Export (Save) Configuration
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 144 Copyright © 2021 Marvell
2: Port 2: WWPN: 21-00-00-24-FF-8F-D8-67 D-Port
HBA Model QLE2740 SN: AFD1536Y03312
3: Port 1: WWPN: 21-00-00-24-FF-00-27-B3 SFP not installed
HBA Model QLE2662 SN: AFE1227F06193
4: Port 1: WWPN: 20-01-00-0E-1E-08-D9-A0 SFP not installed
5: Port 2: WWPN: 20-01-00-0E-1E-08-D9-A1 SFP not installed
(p or 0: Previous Menu; m or 98: Main Menu; ex or 99: Quit)
Please Enter Selection: 1
QConvergeConsole
Version x.y.z (Build xx)
Export (Save) Configuration
======================================================
BA : 0 Port: 1
SN : AFD1536Y03145
BA Model : QLE2692
BA Desc. : QLE2692 Dual Port 16Gb FC to PCIe Gen3 x8 Adapter
W Version : 8.05.41
WPN : 21-00-00-24-FF-8F-D8-66
WNN : 20-00-00-24-FF-8F-D8-66
Link : Online
======================================================
1: Save HBA Parameters
2: Save Firmware Preload Table
3: Save Firmware Serdes Table
Save Flash (-b)
2. Adapter Configuration2. FC Adapter Configuration11. Export (Save) Configuration<port selection>1. Save
Flash
From the Export (Save) Configuration menu, select the Save Flash option to save
changes to the Flash memory to a file.
NOTE
On Solaris only:
Reset is disabled if the system detects storage SR-IOV or VFs.
The flash update does not take effect until the system is restarted.