Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
Adapter Port Alias (-pa)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 112 Copyright © 2021 Marvell
Adapter Port Alias (-pa)
2. Adapter Configuration2. FC Adapter Configuration2. Adapter Port Alias
From the FC Adapter Configuration menu, select the Adapter Port Alias option.
From the port menu, select a port to view or change its port alias. The port’s
information is displayed followed by a prompt identifying the current port alias in
brackets. To change the port alias, enter the new value and press ENTER. (If you
do not want to change the alias, just press ENTER.) The following is an example
of changing the port alias from 0 to 1:
FC Adapter Configuration
HBA Model QLE2562 SN: GFC0819H89653
1: Port 1: WWPN: 21-00-00-1B-32-0C-95-0C Link Down
2: Port 2: WWPN: 21-01-00-1B-32-2C-95-0C Link Down
(p or 0: Previous Menu; m or 98: Main Menu; ex or 99: Quit)
Please Enter Selection: 1
=======================================================
HBA : 0
Physical Port : 1
Port Alias : 0
HBA SN : GFC0819H89653
HBA Model : QLE2562
HBA Desc. : QLE2562 PCI Express to 8Gb FC Dual Channel
WWPN : 21-00-00-1B-32-0C-95-0C
WWNN : 20-00-00-1B-32-0C-95-0C
Link : Link Down
=======================================================
Port Alias [0]: 1
Update completed. Changes have been saved to HBA WWPN
21-00-00-1B-32-0C-95-0C!
HBA Parameters
2. Adapter Configuration2. FC Adapter Configuration3. HBA Parameters
From the FC Adapter Configuration menu, select the HBA Parameters option.
From the port menu, select a port to open the HBA Parameters Menu with options
to view adapter parameters, configure adapter parameters, and restore adapter
defaults. For example:
FC Adapter Configuration
HBA Model QLE2692 SN: AFD1536Y03145