Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
FC VPD Information (-i)
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 106 Copyright © 2021 Marvell
FC VPD Information (-i)
1. Adapter Information3. FC VPD Information
From the FC Adapter Information menu, select the FC VPD Information option.
From the Adapter Information menu, select an adapter port for which to view VPD
information. For example:
QConvergeConsole
CLI - Version x.y.z (Build xx)
Adapter Information
HBA Model QLE2770 SN: AFD1923Y07510
1: Port 1: WWPN: 21-00-34-80-0D-3B-89-B0 Online
HBA Model QLE2692 SN: RFD1610K18231
2: Port 1: WWPN: 21-00-00-24-FF-75-2B-9C Online (FEC)
3: Port 2: WWPN: 21-00-00-24-FF-75-2B-9D
Unsupported SFP Vendor
(p or 0: Previous Menu; m or 98: Main Menu; ex or 99: Quit)
Please Enter Selection: 1
------------------------------------------------------------------
HBA : 1 Port 1
NOTE
For a QLE8362 Fibre Channel or Converged Network Adapter, the port
information also includes the HBA Temperature in degrees Celsius.
For adapters other than QLE2562 and QLE2764 adapters, the port
information’s Running Firmware Version is labeled Driver
Firmware Version.
For Marvell QLogic 16Gb and 32Gb Fibre Channel adapters (QLE26xx,
QLE27xx, and QLE83xx), the HBA Status indicates whether the
forward error correction (FEC) option is enabled; for example, Online
(FEC). (FEC is disabled by default; to enable FEC, see “FEC (-fec)” on
page 149.) The FEC feature is supported only on Marvell QLogic 16Gb
and 32Gb Fibre Channel adapters if the current adapter port is
connected to a Brocade switch with FEC support.
For QLE27xx, if the adapter is connecting and linking up as 32Gb, the
FEC feature is automatically always ENABLED, regardless of the setting
of FEC as disabled or enabled.