Users Guide
Table Of Contents
- Table of Contents
- Preface
- Part I General CLI Information
- Part II Noninteractive Commands
- 4 General Noninteractive Commands
- 5 Fibre Channel Noninteractive Commands
- Displaying System Information (Command Line Options -g, -z)
- Command Format
- Command Summary
- -a
- -b (Flash Update; Save Flash)
- -bbcr (BB Credit Recovery)
- -c (Display HBA Parameters)
- -ctp (CT Ping Test)
- -d (Driver Update)
- -dm (Transceiver Diagnostics Monitoring Interface [DMI])
- -dp (Diagnostic Port Test)
- -dport (Diagnostics Port)
- -e (Boot Devices Configuration)
- -ei
- -f
- -fcep (Diagnostics FC Ping [ELS Echo Ping])
- -fcp (Ping Test)
- -fec (FEC Enable/Disable)
- -fg (Display Driver Persistent Binding Settings)
- -ftr (CT FTR Test)
- -fs (Driver Parameters)
- -fwdump (Firmware Dump)
- -g
- -gs (Configure Parameters [Monitoring])
- -h (Help)
- -ha (Adapter Alias [FCoE Configuration])
- -i (FC Adapter Information; FC VPD Information; FC VFC Information)
- -kl (Loopback Test)
- -kr (Read Write Buffer Test)
- -l (FC Target/LUN Information)
- -ls (Display Parameters [HBA Statistics]; Link Status)
- -m (Selective LUNs)
- -mbiv (Flash/MBI Information)
- -n (Configure HBA Parameters)
- -o (Redirect Standard Output To a File)
- -p (Target Persistent Bindings)
- -pa (Adapter Port Alias [FCoE Configuration])
- -pc (Adapter Personality Change)
- -pl (Persistent Names [udev] – Linux only)
- -q (Target Link Speed [iiDMA])
- -qos (Quality of Service [QoS])
- -r (Parameters Update; Save HBA Parameters)
- -rdp (Read Diagnostics Parameter)
- -s (Suppress Output [Silent Mode])
- -scm (Congestion Management)
- -sp (FC Board Config Update)
- -t (FC Target/LUN Information)
- -tb (Target Beacon)
- -tm (Temperature Monitor)
- -tp (Topology)
- -trace (FCE Trace)
- -u (Firmware Preload Table Update)
- -v (QCC CLI Version Information)
- -vp (Virtual Ports [NPIV])
- -x (XML Output [Legacy])
- -x2 (XML Output)
- -z (All Information)
- Part III Interactive Commands
- 6 Fibre Channel Interactive Commands
- Adapter Information
- Adapter Configuration
- Adapter Alias (-ha)
- Adapter Port Alias (-pa)
- HBA Parameters
- Target Persistent Binding (-p)
- Persistent Names (-pl)
- Boot Devices Configuration
- Virtual Ports (NPIV) (-vp)
- Target Link Speed (iiDMA)) (-q)
- Driver Parameters (-fs)
- Selective LUNs (-m)
- Quality of Service (QoS) (-qos)
- Export (Save) Configuration
- Generate Reports
- Personality (-pc)
- FEC (-fec)
- BB Credit Recovery (-bbcr)
- Adapter Updates
- Adapter Diagnostics
- Monitoring
- Refresh
- Help (-h)
- Exit
- A Revision History
- 6 Fibre Channel Interactive Commands
- Glossary
6–Fibre Channel Interactive Commands
FC Port Information
Doc. No. TD-000947 Rev. 1
Janurary 29, 2021 Page 104 Copyright © 2021 Marvell
Host NQN
1
: nqn.2014-08.org.nvmexpress:uuid:4c4c4544-0038-4310-8050-c3c04f5a5631
HBA Instance : 0
HBA Model : QLE2770
HBA Description : QLogic QLE2770 1x32Gb QLE2770 FC HBA
HBA ID : 0-QLE2770
HBA Alias :
HBA Port : 1
Port Alias :
Node Name : 20-00-34-80-0D-3B-89-B0
Port Name : 21-00-34-80-0D-3B-89-B0
Port ID : 01-0A-00
Principal Fabric WWN
2
: 10-00-00-05-33-7E-5F-A3
Adjacent Fabric WWN
3
: 20-0A-00-05-33-7E-5F-A3
Serial Number : AFD1923Y07510
Driver Version : STOR Miniport 9.4.2.20 A6 DBG
BIOS Version : 3.65
Running Firmware Version
4
: 9.06.00
Running MPI Firmware Version : 3.01.00
Running PEP Firmware Version
5
: 3.00.29
Flash BIOS Version : 3.65
Flash FCode Version : N/A
Flash EFI Version : 7.29
Flash Firmware Version : 9.06.00
Flash MPI Firmware Version : 3.01.00
Flash PEP Firmware Version : 3.00.29
Actual Connection Mode : Point to Point
Actual Data Rate : 16 Gbps
Supported Speed(s) : 8 16 32 Gbps
Chip Model Name : ISP2812-based Dual Port 64Gb Fibre Channel to PCIe Adapter
1
Host NQN appears only for 2600 Series Adapter models QLE2690, QLE2692, QLE2964,
QLE2964L, and 2700 Series Adapter models QLE2740, QLE2742, QLE2764, QLE2770, QLE2772,
QLE2774 on which the port link is up. It shows the host NVMe qualified name (NQN) for NVM
Express (NVMe) over Fibre Channel (NVMe-oF) Principal Fabric WWN of the principal switch
in the fabric.
2
Principal Fabric WWN is the WWN of the principal switch in the fabric.
3
Adjacent Fabric WWN is the WWN of the switch to which the adapter port is directly
connecting.
4
If the Running MPI Firmware Version description is Not Running, the management port
interface (MPI) firmware is not currently being loaded nor is it active.
5
In this example, the Running PEP Firmware Version description is available because the
PCIe processor (PEP) firmware is currently being loaded.