S560T Laser Touch QSC_A00.
S560T Laser Touch QSC_A00.book Page 2 Wednesday, June 22, 2016 2:39 PM About Notes NOTE: A NOTE indicates important information that helps you make better use of your projector. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. __________________ Information in this document is subject to change without notice. © 2016 Dell Inc. All rights reserved.
S560T Laser Touch QSC_A00.book Page 3 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector Set Up Touch on Your Projector Usage Notice Precautions Please follow all warnings, precautions and maintenance as recommended in this user's manual. WARNING: Do not disassemble Touch Unit. WARNING: Do not use, store, or leave the Touch Unit near fire, or in places with a high temperature, e.g., in direct sunlight, or in sun-heated cars.
S560T Laser Touch QSC_A00.book Page 4 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector How it works • • • • 4 The Touch Unit covers the entire whiteboard with a thin invisible IR light. When a finger or stylus breaks into the light curtain, the IR light reflects on to the IR camera. The camera module tracks multiple touch points and reports the positions to a computer via USB. To optimize the touch function, the screen non-flatness should be less than 0.2 inch (5 mm).
S560T Laser Touch QSC_A00.book Page 5 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector Specifications I. Touch Unit (S560T Only) Laser Safety Class 1 Touch Unit to Screen Distance 0.79 inch ~3.94 inch (20 mm~100 mm) @81"~100" 1080p LED Indicator Blue/Red I/O Port Interactive Jack x1 Touch sensor adjustment 2-knob adjustment and with visible light ID Size(W*L*H) 5.91 (W) x 1.97 (L) x 1.57 (H) inch (150.0 (W) x 50.0 (L) x 40.0 (H) mm) Weight < 330 g Power Consumption 12V/0.
S560T Laser Touch QSC_A00.book Page 6 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector Display mode Supports ceiling mode only Calibration 1. Manual Calibration : 9 points manual calibration , 1080p model: +/- 6 pixels (screen non-flatness <0.2 inch (5mm)) 2. Auto calibration : 1080p model:+/- 8 pixels (screen non-flatness <0.2 inch (5mm)) 3.
S560T Laser Touch QSC_A00.book Page 7 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector III. OS requirement System Requirements Processor Type Intel Core™ i3 (or above) or same level of AMD Core. RAM 2 GB or More Number of touch Installation of S560x Interactive Utility*1 points supported For first-time setup*2 For subsequent use *3 Windows 7/8/10 10 touch points Supported Not required *4 Mac OS X 1 touch point Supported Required, please install the setup utility on all Mac OS (10.
S560T Laser Touch QSC_A00.book Page 8 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector Step 1: Environment Check A Make sure the projector is installed under the following conditions: - The wall should be strong enough to avoid projection image flickering. - Do no install the projector or screen in a location subject to direct sunlight. If the projector or the screen is subjected to direct sunlight, the interactive function may not operate correctly.
S560T Laser Touch QSC_A00.book Page 9 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector 2 Mount the Touch Unit on a wall surface. 1080p (16:9) image NOTE: The Touch Unit must be mounted on the same surface as the projected image. B S560T Whiteboard size guidance When mounting the Touch Unit on a whiteboard please follow the guidelines below: Spaces of a & b are reserved to cater for touch unit. • Dimension a = 50 mm • Dimension b = 77 mm W1 W2 81.0 [2057] S1 ≥ 44.7 [1136] ≥ 74.
S560T Laser Touch QSC_A00.book Page 10 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector D-2) Insert 0.2 inch (5mm) thickness gauge at point 1~9 positions in the following order: Horizontal: -Measure point 1, 2 & 3. Step 2: Installing the Touch Unit 1 Open top cover by Phillips screwdriver (model: number 1). -Measure point 4, 5 & 6. -Measure point 7, 8 & 9. Vertical: -Measure point 1, 4 & 7. -Measure point 2, 5 & 8. -Measure point 3, 6 & 9. D-3) If 0.
S560T Laser Touch QSC_A00.book Page 11 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector - 0.79~3.94 inch (20~100 mm) from bottom of the Touch Unit 2-4. The two black screws included are tapping screws, suitable for aluminum honeycomb board which is the typical whiteboard material. NOTE: For other surfaces such as wood or concrete wall, use suitable screw types. 2 2-1. Clean the surface. 2-2.
S560T Laser Touch QSC_A00.book Page 12 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector 4 Connect the power cord to the Touch Unit. NOTE: The L-side connector should be connected to the Touch Unit.
S560T Laser Touch QSC_A00.book Page 13 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector Step 3: Install Utility Software A System requirements To ensure normal operation of the touch function, follow below requirements to check your system condition. System requirement Processor Type Intel Core™ i3 (or above) or same level of AMD Core.
S560T Laser Touch QSC_A00.book Page 14 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector *2 : S560T requires first-time alignment and calibration, ensure you complete setup process before use *3 : .NET Framework 4.0 installation is required *4 : Mac OS support 1 touch point only B Install software utility from CD.
S560T Laser Touch QSC_A00.book Page 15 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector Step 4: Setup Wizard Please follow S560T Setup Wizard to complete Touch Unit installation procedure. Step 5: Adjust Touch Sensor 1 Press button to switch the Touch Unit to alignment mode: red light will be blinking at the indicator.
S560T Laser Touch QSC_A00.book Page 16 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector 2 Set computer to project in "Projector Only" mode. Connect USB cable from projector to computer. NOTE: Make sure the Touch Unit has already been switched to alignment mode (Step 1) before connecting the USB cable from projector to computer to avoid interference or unwanted touch triggers during first-time setup, prior proper calibration. 3 Turn both adjustment knobs clockwise completely.
S560T Laser Touch QSC_A00.book Page 17 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector If not, turn the black and grey knobs to adjust each beams. (Step 4 & 5) Black knob : to move visible light on the light stickers Grey knob : to adjust visible light symmetrically at the same level. The visible light should be located within grey zone. 8 Replace the top cover. 7 Press button to exit alignment mode, red blinking light will go off, leaving the indicator light blue.
S560T Laser Touch QSC_A00.book Page 18 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector Step 6: Touch Area Setting B Select Manual Touch Area Setting: A Select Auto Touch Area Setting: NOTE: • Quit all software applications • Reduce ambient light • Do not obstruct or shake lens during Touch Area Setting • Check if projection image is clear. If not, adjust focus to sharpen the image If fail message pops up, switch to Manual Touch Area Setting. 18 B-1.
S560T Laser Touch QSC_A00.book Page 19 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector Remark: Captured image shows the actual camera view, which is reversed from projection image. For example: P1 is lower right corner, P2 is lower left corner and so on. Step 3: Finally, check again if the green frame completely overlaps the projected white frame. If not, fineadjust again. B-3. When the Touch Area is correctly located then click exit button. B-2.
S560T Laser Touch QSC_A00.book Page 20 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector Step 7: Calibration A Auto Calibration: NOTE: If the fail message pops up, follow below steps to trouble-shoot and do Auto Calibration again. • Close all software application • Reduce ambient light • Do not obstruct or shake lens during calibration • Check if projection image is clear.
S560T Laser Touch QSC_A00.book Page 21 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector Step 8: Trouble-shooting Viewer Sometimes infrared red light (IR light) from ambient light sources may interfere with touch performance. The troubleshooting viewer shows real time image for debugging purposes. Any light interference is marked in green. If green obstacles appear within image area, please remove to secure proper interactivity.
S560T Laser Touch QSC_A00.book Page 22 Wednesday, June 22, 2016 2:39 PM Set Up Touch on Your Projector Step 10: Touch Sensitivity When touch function is unresponsive or writing is intermittent, you can adjust the sensitivity by adjusting the Touch Sensitivity level: - Default: 4 - Max.: 10 (most sensitive) - Min.: 0 (least sensitive) NOTE: Touch Sensitivity is not adjustable under Pen Mode.
S560T Laser Touch QSC_A00.book Page 23 Wednesday, June 22, 2016 2:39 PM Troubleshooting Troubleshooting Q1 What to do when Touch function is not accurate? A: For better accuracy, you should set to "Projector Only" display mode before calibration. A-1: Touch accuracy may be impacted if Windows default display setting has been changed. A-1-1 : Go to the setting page: Start menu > Control Panel > Appearance and Personalization A-1-2 : Select "Smaller - 100%(Default) " and click "Apply".
S560T Laser Touch QSC_A00.book Page 24 Wednesday, June 22, 2016 2:39 PM Troubleshooting If you adjust the computer's resolution or connect a different computer. Failure symptom : In the center of the board the cursor and pen are aligned. As you move left or right the pen and cursor begin to separate. This issue maybe from graphics card driver setting. For Intel graphics cards, do the following: 1 Confirm the graphic card output resolution is same as projector information.
S560T Laser Touch QSC_A00.book Page 25 Wednesday, June 22, 2016 2:39 PM Troubleshooting Q2 What to do when touch function is not accurate or not working when using a different display mode (duplicate/ extension)? A-1: Duplicate mode: It will be accurate if the laptop and the projector are in the same resolution. Set the "Scaling" Setting to "Maintain Display Scaling" followed by Q1 A-2, and use calibration function again. Extended mode: Set to "Only projector" mode and use the calibration function.
S560T Laser Touch QSC_A00.book Page 26 Wednesday, June 22, 2016 2:39 PM Troubleshooting Go to "Control panel" -> "Tablet PC settings" -> "Setup" and follow the touch screen settings. Q4 What to do when projection area corner is insensitive or intermittent lines are observed? A: 1 Adjust the level of Touch Sensitivity to enhance sensitivity. See Step 10 Touch Sensitivity for trouble-shooting. 2 If Touch function remains insensitive, please check the optical port condition.
S560T Laser Touch QSC_A00.book Page 27 Wednesday, June 22, 2016 2:39 PM Troubleshooting Q5 Why cannot the computer boot when the USB cable which connects PC and projector is already plugged in? A: 1 Unplug USB cable from computer, and then re-boot computer. 2 Go to BIOS setup page of computer and modify the "Boot Sequence" Choose Hard disk as top priority, save the change and reboot computer.
S560T Laser Touch QSC_A00.book Page 28 Wednesday, June 22, 2016 2:39 PM Troubleshooting A-4 Go to Power Options in Control Panel, check USB selective suspend settings status in USB settings under Advance Settings. Switch to "Disabled". A-5 Go to official website of the laptop/PC manufacturer, and update USB driver to latest version. A-6 Use the USB cable included with your projector and check again. If an USB extension is needed, a USB Hub or a certificated active extension USB cable is required.
S560T Laser Touch QSC_A00.book Page 29 Wednesday, June 22, 2016 2:39 PM Troubleshooting Q7 What to do when the mouse is blocked? A: 1 Open the curtain cover by screwdriver. 2 Press the button to switch to visible light mode (See step 5: Adjust Touch Sensor) and the mouse will be unblocked. Then follow step 5: Adjust Touch Sensor as in page 15. Q8 Why utility icon ( ) is red, not green ( / )? A: Red icon ( ) indicates a failed connection.
S560T Laser Touch QSC_A00.book Page 30 Wednesday, June 22, 2016 2:39 PM Troubleshooting 5 Control Panel > Hardware and Sound > Power Options > Change plan settings > Change advanced power settings > USB settings > USB selective suspend setting. Switch to "Disabled". 6 Go to official website of the laptop/PC manufacturer, and update USB driver to latest version. 7 Go to official website of the laptop/PC manufacturer, and update BIOS driver to latest version.
S560T Laser Touch QSC_A00.book Page 31 Wednesday, June 22, 2016 2:39 PM Troubleshooting - For better accuracy, please do Manual Calibration. - If an overlarge offset is observed, please perform Manual Calibration and see step 7: Calibration as in page 20. Q10 What to do when Auto Calibration and Auto Touch Area Setting both fail? A: 1 Check "Ceiling Mount" OSD setting first. The interactive function supports Ceiling Mode only.
S560T Laser Touch QSC_A00.book Page 32 Wednesday, June 22, 2016 2:39 PM Troubleshooting a b c d e Quit all software applications Reduce ambient light Do not obstruct or shake lens during calibration Check if projection image is clear. If not, adjust focus to sharpen the image. If the "Auto Touch Area Setting failed" or "Auto Calibration failed" message pops up on screen again, please switch to Manual Mode to do Touch Area Setting and Calibration. 2 Please check Projector Lamp Power Mode selection.
S560T Laser Touch QSC_A00.book Page 33 Wednesday, June 22, 2016 2:39 PM Troubleshooting 3 Please check Projector Color Mode selection. To ensure accuracy of both Auto Touch Area Setting and Auto Calibration, it is suggested to switch Color mode to Bright Mode. Q11 What to do when the mouse cursor ( ) flashes or jumps on screen, or when Touch function does not work well at certain projected area? A: 1 Please confirm the Touch sensor had been adjusted and Laser Beam is parallel to the screen.
S560T Laser Touch QSC_A00.book Page 34 Wednesday, June 22, 2016 2:39 PM Troubleshooting 5 To keep at least 2 inch (50 mm) clearance boundary of the projected image to avoid reflection interference. Q12 What to do when there is only a single touch point? A: 1 Mac computers support single touch point only. 2 For WINDOWS computer, please refer to below suggestions 2.1 Re-plug USB cable from computer and check again. 2.2 Go to "Control Panel" and make sure "Tablet PC Components" is selected.
S560T Laser Touch QSC_A00.book Page 35 Wednesday, June 22, 2016 2:39 PM Appendix B: Accessory Appendix B: Accessory Item Description Quantity 1 Touch Unit 1 2 White Screw M2.
S560T Laser Touch QSC_A00.book Page 36 Wednesday, June 22, 2016 2:39 PM Appendix B: Accessory 7 Double-sided tape (for base plate) 1 10 CD for User Manual and Utility Software Documentation Dell Interactive Projector S560P/S560T Contents: • User's Guide • Setup Utility • Touch Setup Guide (S560T only) ll rig ht sr es er ve d. 018T WNA00 P/N 18TWN Rev. A00 P/N 36.76G01G001 July 2016 Made in China 8 16.
S560T Laser Touch QSC_A00.
S560T Laser Touch QSC_A00.book Page 2 Wednesday, June 22, 2016 2:39 PM Printed in China. Printed on recycled paper. w w w.d e l l .
