Dell Precision 7530 Solid State Drive Installation Guide
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents 1 Before you begin............................................................................................................................................ 4 Safety instructions............................................................................................................................................................. 4 Before working inside your computer........................................................................................................................
1 Before you begin Safety instructions Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that shipped with your computer. • A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.
Safety precautions The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions. Observe the following safety precautions before you perform any installation or break/fix procedures involving disassembly or reassembly: • • • • • • Turn off the system and all attached peripherals. Disconnect the system and all attached peripherals from AC power. Disconnect all network cables, telephone, and telecommunications lines from the system.
• Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads. • When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you discharge static electricity from your body.
Transporting sensitive components When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport. Lifting equipment Adhere to the following guidelines when lifting heavy weight equipment: CAUTION: Do not lift greater than 50 pounds. Always obtain additional resources or use a mechanical lifting device. 1 Get a firm balanced footing.
2 Solid State Drive—SSD Installing the solid state drive 1 Follow the procedure in Before working inside your computer. 2 Remove the SD card: a b 3 Press the SD card in to release it from the system. Remove the SD card out of the system. Remove the base cover: a b c d 8 Loosen the 7 captive screws that secure the base cover to the system [1]. Pry open the base cover starting from the two recess point at the top edge of the system [2]. Pry around the edges of the base cover [3].
4 Remove the 6-cell battery: a b c Disconnect the battery cable from the connector on the system board [1]. Remove the 3 (M2.5x3.0) screws that secure the battery to the system [2]. Remove the battery away from the system [3].
5 Remove the 4-cell battery: a b c 10 Disconnect the battery cable from the connector on the system board [1]. Remove the 2 (M2.5x3.0) screws that secure the battery to the system [2]. Remove the battery away from the system [3].
6 To install the M.2 SSD module (Slot 4): a b c d Place the M.2 SSD into its slot in the system [1]. Fasten the single (M2.0x3.0) screw to secure the M.2 SSD to the system board [2]. Place the thermal plate above the M.2 SSD module [3]. Fasten the single (M2.0x3.0) screw to secure the thermal plate to the M.2 SSD [4]. NOTE: Repeat the above steps to install the M.2 SSD card in Slot 3 and Slot 5.
Solid State Drive—SSD
Solid State Drive—SSD 13
7 Install the 4-cell battery: a b c 8 Place the battery onto its slot in the system [1]. Replace the 2 (M2.5x3.0) screws to secure the battery to the system [2]. Connect the battery cable to the connector in the system board [3]. Install the 6-cell battery: a b c 14 Place the battery onto its slot in the system [1]. Replace the 3 (M2.5x3.0) screws to secure the battery to the system [2]. Connect the battery cable to the connector in the system board [3].
9 Install the base cover: a b Slide the base cover into its slot until it clicks into place [1, 2]. Tighten the captive screws to secure the base cover to the system [3].
10 Install the SD card: a 16 Slide the SD card into its slot until it clicks into place.
11 Follow the procedure in After working inside your computer.
3 Getting help Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1 Go to Dell.com/support. 2 Select your support category.
