Users Guide
10-20
Dell Precision 410 Mini Tower Systems User’s Guide
If you are installing an external SCSI device
, connect one end of the external SCSI
cable to the SCSI bus connector on the back of the device. Attach the other end
of the external SCSI cable to the SCSI connector on the system back panel.
NOTE: Dell offers an external SCSI 68-pin-to-50-pin adapter kit for connecting
SCSI-3 devices to the SCSI-2 connector on the Precision 410 system back panel.
Contact your Dell sales representative for more information.
&RQQHFW W KH 6&6, GHYLFHV WR SRZHU
If you are installing an internal SCSI device
, connect a DC power cable to the
power input connector on the SCSI device.
If you are installing an external SCSI device
, connect the socket end of the
power cable into the AC power receptacle on the back of the SCSI device.
Connect the other end of the power cable into a standard electrical wall
outlet.
Check all other cable connections. Fold all internal cables out of the way to pro-
vide airflow for the fan or cooling vents.
,I \RX LQVWDOOHG DQ H[WHUQDOO\ DFFHVVLEOH GHYLFH UHPRYH WKH IURQW EH]HO
DQG UHPRYH WKH IURQWSDQHO LQVHUW IRU WKH GULYH ED\ IURP WKH IURQW
EH]HO 7KHQ UHSODFH WKH IURQW EH]HO
For instructions, see “Removing and Replacing the Front Bezel” and “Removing
and Replacing Front-Panel Inserts” found earlier in this chapter.
5HSODFH WKH FRPSXWHU FRYHU 7KHQ UHFRQQHFW \RXU FRPSXWHU DQG SHULSK
HUDOV WR WKHLU SRZHU VRXUFHV DQG WXUQ WKHP RQ
NOTE: After you remove and replace the cover, the chassis intrusion detector will
cause the following message to be displayed at the next system start-up:
ALERT! Cover was previously removed.
7R UHVHW WKH FKDVVLV LQWUXVLRQ GHWHFWRU HQWHU WKH 6\VWHP 6HWXS SURJUDP
DQG UHVHW &KDVVLV ,QWUXVLRQ WR 1RW 'HWHFWHG
See Chapter 3, “Using the System Setup Program,” for instructions.
NOTE: If a setup password has been assigned by someone else, contact your
network administrator for information on resetting the chassis intrusion detector.
,I QHFHVVDU\ XSGDWH WKH GULYH V\VWHP FRQILJXUDWLRQ LQIRUPDWLRQ LQ WKH
6\VWHP 6HWXS SURJUDP
For any SCSI devices, the respective category under Drives: Primary or Drives:
Secondary should be set to None. For instructions, see Chapter 3, “Using the
System Setup Program.”
,I \RX LQVWDOOHG D 6&6, KDUGGLVN GULYH SDUWLWLRQ DQG IRUPD W WKH GULYH
7KHQ LQVWDOO WKH RSHUDWLQJ V\VWHP
For instructions, see the next subsection, “Partitioning and Formatting SCSI
Hard-Disk Drives,” and your operating system documentation.
23205BK0.BK : 23205100.FM Page 20 Wednesday, March 18, 1998 1:51 PM
Downloaded from www.Manualslib.com manuals search engine