Dell Precision 360 Service Manual Dell Precision™ 360 Service Manual Before You Begin Inside Your Computer Front Panel I/O Panel Control Panel Chassis Intrusion Switch Power Supply System Board Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
Before You Begin: Dell Precision 360 Service Manual Back to Contents Page Before You Begin Dell Precision™ 360 Service Manual Recommended Tools Precautionary Measures Protecting Against Electrostatic Discharge This section provides procedures for removing and replacing the components, assemblies, and subassemblies in the Dell Precision™ 360 computer.
Before You Begin: Dell Precision 360 Service Manual NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network wall jack. 3. Disconnect any telephone or telecommunication lines from the computer. 4. Disconnect your computer and all attached devices from electrical outlets, and then press the power button to ground the system board.
Inside Your Computer: Dell Precision 360 Service Manual Back to Contents Page Inside Your Computer Dell Precision™ 360 Service Manual Mini-Tower Computer Desktop Computer Cable Colors – Mini-Tower and Desktop Computers System Board Components Jumper Settings CAUTION: Before performing any of the procedures in this section, follow the safety instructions in the System Information Guide.
Inside Your Computer: Dell Precision 360 Service Manual 1 hard drive 6 heat sink and blower assembly 2 internal speaker (optional) 7 power supply 3 chassis intrusion switch 8 floppy drive (optional) 4 system board 9 CD/DVD drive 5 padlock ring Desktop Computer 1 CD/DVD drive 6 microprocessor airflow shroud 2 floppy drive 7 security cable slot 3 hard drive 8 power supply 4 system board 9 chassis intrusion switch 5 padlock ring Cable Colors – Mini-Tower and Desktop Computers file:///C|/infod
Inside Your Computer: Dell Precision 360 Service Manual Device Cable Color Hard drive Blue pull tab Floppy drive Black pull tab CD/DVD drive Orange pull tab I/O panel Yellow pull tab System Board Components 1 floppy-drive connector (FDD) 14 AGP card connector (AGP) 2 secondary-drive connector (SEC_IDE) 15 PCI card connectors (PCI1, PCI2, PCI3, PCI4) 3 hard-drive connector (IDE1) 16 front-panel audio cable connector (FP_AUDIO) 4 battery socket (BATTERY) 17 telephony connector (TELE) 5 pa
Inside Your Computer: Dell Precision 360 Service Manual (FRONT_PANEL) 8 standby power light (PWR_LED) 21 rear fan connector (REAR_FAN2) 9 internal speaker (SPKR) 22 microprocessor and heat-sink connector (CPU_0 PIN_#A1) 10 clear CMOS jumper (CMOS) 23 microprocessor fan connector (CPU_FAN) 11 serial ATA connector (SATA_1) 24 memory module connectors (1, 3) 12 front fan (FRONT_FAN) 25 power connector (PWR) 13 serial ATA connector (SATA_0) 26 memory module connectors (2, 4) Jumper Settings NOTIC
Inside Your Computer: Dell Precision 360 Service Manual jumpered unjumpered Back to Contents Page file:///C|/infodev/2013/eDoc/ws360/SM/inside.
Front Panel : Dell Precision 360 Service Manual Back to Contents Page Front Panel Dell Precision™ 360 Service Manual Removing the Front Panel – Mini-Tower Computer Removing the Front Panel – Desktop Computer Replacing the Front Panel CAUTION: Before performing any of the procedures in this section, follow the safety instructions in the System Information Guide. Removing the Front Panel – Mini-Tower Computer 1.
Front Panel : Dell Precision 360 Service Manual 2 bottom panel 3 front-panel tabs (3) 4 top-panel tabs (8) b. Close the cover and remove the front bezel. 3. Remove the screw that holds the control panel to the computer, and remove the control panel. Removing the Front Panel – Desktop Computer 1. Disconnect and remove all disk drives (for more information, see "Drives" in your User's Guide.) 2. Release the front panel by pressing each of the seven front-panel release tabs. Desktop Computer 3.
I/O Panel: Dell Precision 360 Service Manual Back to Contents Page I/O Panel Dell Precision™ 360 Service Manual I/O Panel Components Removing the I/O Panel Replacing the I/O Panel CAUTION: Before performing any of the procedures in this section, follow the safety instructions in the System Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components.
I/O Panel: Dell Precision 360 Service Manual 1 chassis-intrusion switch connector 6 headphone connector 2 speaker connector 7 USB 2.0 connector 3 audio connector 8 USB 2.0 connector 4 front-panel connector 9 diagnostic lights (4) 5 control-panel connector Removing the I/O Panel 1. Remove the front panel. 2. Disconnect all cables that are connected to the I/O panel. Note the routing of the control panel cable as you remove it from the computer so that you can replace it correctly. 3.
I/O Panel: Dell Precision 360 Service Manual Desktop Computer Replacing the I/O Panel To replace the I/O panel, follow the removal procedures in the reverse order. Back to Contents Page file:///C|/infodev/2013/eDoc/ws360/SM/iopnl.
I/O Panel: Dell Precision 360 Service Manual file:///C|/infodev/2013/eDoc/ws360/SM/iopnl.
Control Panel: Dell Precision 360 Service Manual Back to Contents Page Control Panel Dell Precision™ 360 Service Manual Control-Panel Components Removing the Control Panel Replacing the Control Panel CAUTION: Before performing any of the procedures in this section, follow the safety instructions in the System Information Guide.
Control Panel: Dell Precision 360 Service Manual 1 hard-drive access light 2 power button 3 screw hole 4 alignment hole 5 control-panel connector 6 power light Removing the Control Panel 1. Remove the front panel. 2. Disconnect the control-panel cable from the I/O panel connector. 3. Disconnect the I/O panel cable from the connector on the system board. To locate the system board connector, see "System Board." 4. Remove the mounting screw from the control panel. 5.
Control Panel: Dell Precision 360 Service Manual Desktop Computer 1 control panel file:///C|/infodev/2013/eDoc/ws360/SM/cntrlpnl.
Control Panel: Dell Precision 360 Service Manual 2 mounting screw Replacing the Control Panel Follow the removal procedure in reverse order, ensuring that the tabs on the top panel, bottom panel, and front panel are secure. Back to Contents Page file:///C|/infodev/2013/eDoc/ws360/SM/cntrlpnl.
Chassis Intrusion Switch: Dell Precision 360 Service Manual Back to Contents Page Chassis Intrusion Switch Dell Precision™ 360 Service Manual Removing the Chassis Intrusion Switch Resetting the Chassis Intrusion Detector Replacing the Chassis Intrusion Switch CAUTION: Before performing any of the procedures in this section, follow the safety instructions in the System Information Guide.
Chassis Intrusion Switch: Dell Precision 360 Service Manual Desktop Computer 3. Slide the chassis intrusion switch into its slot and reconnect the cable to the connector on the control panel. Resetting the Chassis Intrusion Detector 1. Enter system setup by pressing during the computer's POST. NOTE: For instructions on using system setup, see the User's Guide. 2. Under the System Security tab, reset the Chassis Intrusion option by pressing the left- or right-arrow key to select Reset.
Power Supply: Dell Precision 360 Service Manual Back to Contents Page Power Supply Dell Precision™ 360 Service Manual Removing the Power Supply Replacing the Power Supply CAUTION: Before performing any of the procedures in this section, follow the safety instructions in the System Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components.
Power Supply: Dell Precision 360 Service Manual 4. Slide the power supply toward the front of the computer approximately 1 inch. 5. Lift the power supply up and out of the computer. Replacing the Power Supply 1. Slide the power supply into place. 2. Replace the two screws that secure the power supply to the back of the computer frame. 3. Reconnect the DC power cables. 4. On the desktop computer, reattach the power cables to the side of the hard drive. 5.
System Board: Dell Precision 360 Service Manual Back to Contents Page System Board Dell Precision™ 360 Service Manual Removing the System Board Replacing the System Board CAUTION: Before performing any of the procedures in this section, follow the safety instructions in the System Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components.
System Board: Dell Precision 360 Service Manual Replacing the System Board 1. Transfer components from the existing system board to the replacement system board: a. Remove the memory modules and install them on the replacement board. CAUTION: The microprocessor package and heat-sink assembly can get hot. To avoid burns, ensure that the package and assembly have had sufficient time to cool before you touch them. b.