Instruction Manual

Back to Contents Page
Error
Code
Description
Details
3 0 81
Invalid Command Error.
This error indicates that the autoloader received an undefined command or an invalid parameter within a command.
3 0 82
Device Status Not Suitable to
Execute This Command.
If the robotics are busy, some commands cannot be executed at the same time. This error indicates a probable
violation. This is not an error condition, but does result in Busy being reported to the host for the requested SCSI
command.
3 0 83
Inventory Not Valid.
The cartridge inventory is not valid because of manual changes or previous fatal errors. Update the inventory using
the Re-inventory option in the Configuration menu. See "Creating an Inventory of Cartridges" or power cycle.
3 0 84
Source Empty.
There is no cartridge in the location from which a cartridge move was issued.
3 0 85
Destination Full.
The location to which a cartridge move was issued already contains a cartridge.
3 0 86
Import/Export Slot Access
Rejected.
User attempted to access the Import/Export slot, but media removal was prevented by the host.
3 0 87
Operation Timeout.
A command did not complete in the required amount of time.
3 0 88
Communications Error During
Loop-Back.
Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 89
System Test Timeout.
There was a communication timeout between the drive and loader during the System Test.
3 0 8F
Recovered Loader Error.
Loader error recovery successful. Your diagnostic tool can provide details of the original loader error.
3 0 90
Mechanical Initialization
Failure.
The robotics were not able to move to the safe mechanical initialization position. Manual intervention is necessary.
3 0 91
Inventory Scan Failure.
Fatal robotic error occurred during the inventory scan.
3 0 92
Preposition Failed.
Belt positioning error occurred during Preposition command.
3 0 93
Cartridge Load Error.
A failure occurred while trying to load a cartridge a slot to the drive.
3 0 94
Cartridge Unload Error.
A failure occurred while trying to unload a cartridge from the drive to its slot.
3 0 95
Import Error.
An error occurred while trying to import a data cartridge to a carousel slot.
3 0 96
Export Error.
An error occurred while trying to export a data cartridge from its carousel slot. Can be caused by an empty slot that is
expected to be full.
3 0 A0
Carousel Motion Failure.
Error occurred during carousel movement (Position Not Found). Could be caused by a missing or misaligned cartridge
carrier, or an obstruction, or unexpected cartridge in either the carousel path or Import/Export slot.
3 0 A1
Cartridge Transport Position
Error.
Cartridge transport element is unable to reach its desired position. Failure occurred while trying to place a cartridge
into or remove a cartridge from the drive or a slot.
3 0 A2
Gripper Position Error.
Gripper unable to reach position.
3 0 A3
Cartridge Pick Error.
Error occurred while trying to pull a cartridge from the drive or a carousel slot.
3 0 A4
Import/Export Slot Position
Error.
The Import/Export slot door was not in the requested position during device operation. Can be caused by manually
opening the door, or a cartridge or other obstruction is blocking the door. Try removing the cartridge or obstruction,
then power cycle or reset the autoloader.
3 0 A5
Fan Error.
Autoloader Processor Detected a Fan Error.
3 0 B0
ROM Error.
Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 B1
RAM Error.
Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 B2
NVRAM Error.
Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 B3
Controller Timer Failure.
An unrecoverable failure has occurred in the controller timer circuit.
3 0 B4
Loader To Drive
Communication IC Error.
Failure in IC handling loader to drive communication.
3 0 B5
Display Error.
Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 B6
Memory Error.
Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 B7
Timeout on Autoloader
Command
Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 BC
Drive Bug-Checked.
Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.
3 0 BF
Fatal Error.
Power cycle the autoloader and attempt the operation again. If the error recurs, contact your technical support
representative.